Elmo P100HD, 1340 User Manual

Download

INSTRUCTION MANUAL

VISUAL PRESENTER

P100HD

Please read this instruction manual carefully before using this product and

keep it for future reference

IMPORTANT SAFEGUARDS

■ Read Instructions

All the safety and operating instructions should be read before the appliance is operated.

■ Retain Instructions

The safety and operating instructions should be retained for future reference.

■ Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

■ Follow Instructions

All operating and use instructions should be followed.

■ Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol

cleaners. Use a damp cloth for cleaning.

■ Attachments

Do not use attachments not recommended by the product manufacturer as they may cause

hazards.

■ Water and Moisture

Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or

laundry tub, in a wet basement, or near a swimming pool, and the like.

■ Placement

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may

fall, causing serious injury to a child or adult, and serious damage to the product. Use only with

a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the

product. Any mounting of the product should follow the manufacturer’s instructions, and should

use a mounting accessory recommended by the manufacturer.

■ Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation

of the product and to protect it from overheating, and these openings must not be blocked or

covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or

other similar surface. This product should not be placed in a built-in installation such as a

bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have

been adhered to.

■ Power Sources

This product should be operated only from the type of power source indicated on the marking

label. If you are not sure of the type of power supply to your home consult your appliance dealer

or local power company. For products intended to operate from battery power, or other sources,

refer to the operating instructions.

■ Grounding or Polarization

This product may be equipped with either a polarized 2-wire AC line plug (a plug having one

blade wider than the other) or a 3-wire grounding type plug, a plug having a third (grounding)

pin. The 2-wire polarized plug will outlet, try reversing the plug. If the plug still fails to fit,

contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the

polarized plug. The 3-wire grounding type plug will fit into a grounding type power outlet. This

is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to

replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.

■ Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by

items placed upon or against them, paying particular attention to cords at plugs, convenience

receptacles, and the point where they exit from the product.

■ Lightning

For added protection for this product during a lightning storm, or when it is left unattended and

unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or

cable system. This will prevent damage to the product due to lightning and power-line surges.

■ Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can

result in a risk of fire or electric shock.

■ A product and cart combination should be moved with care. Quick stops,

excessive

combination to overturn.

■ Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch

dangerous voltage points or short-out parts that could result in a fire or electric shock. Never

spill liquid of any kind on the product.

■ Servicing

force, and uneven surfaces may cause the product and cart

Do not attempt to service this product yourself as opening or removing covers may expose you

to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

■ Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under

the following conditions:

• When the power-supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the product.

• If the product has been exposed to rain or water.

• If the product does not operate normally by following the operating instructions. Adjust only

those controls that are covered by the operating instructions as an improper adjustment of

other controls may result in damage and will often require extensive work by a qualified

technician to restore the product to its normal operation.

• If the product has been dropped or damaged in any way.

• When the product exhibits a distinct change in performance - this indicates a need for

service.

■ Replacement Parts

When replacement parts are required, be sure the service technician has used replacement

parts specified by the manufacturer or have the same characteristics as the original part.

Unauthorized substitutions may result in fire, electric shock or other hazards.

■ Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform

safety checks to determine that the product is in proper operating condition.

■ Heat

The product should be situated away from heat sources such as radiators, heat registers,

stoves, or other products (including amplifiers) that produce heat.

■ This product includes a Fluorescent Lamps component that contains mercury. Please consult

your state and local regarding proper disposal or recycling, and do not place in the trash.

SA 1965

The lightning flash with arrowhead symbol, within an equilateral triangle, is

intended to alert the user to the presence of uninsulated “dangerous

voltage” within the product’s enclosure that may be of sufficient magnitude

to constitute a risk of electric shock to persons.

SA 1966

The exclamation point within an equilateral triangle is intended to alert the

user to the presence of important operating and maintenance (servicing)

instructions in the literature

This symbol [crossed-out wheeled bin WEEE Annex IV] indicates

separate collection of waste electrical and electronic equipment in

the EU countries.

Please do not throw the equipment into the domestic refuse.

Please use the return and collection systems available in your

country for the disposal of this product.

INFORMATION

CAUTION:

the manufacturer could void the user’s authority to operate the equipment.

PRODUCT TO RAIN OR MOISTURE.

WARNING:

TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS

The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC

Certification or Declaration of this device and may cause interference levels which exceed the limits

established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded

equipment interface cable with this device. If this equipment has more than one interface connector, do

not leave cables connected to unused interfaces. Changes or modifications not expressly approved by

FOR UNITED STATES USERS:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in

accordance with the instruction manual, may cause harmful interference to radio communications. Operation

of this equipment in a residential area is likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

USER-INSTALLER

Your authority to operate this FCC verified equipment could be voided if you make changes or modifications

not expressly approved by the party responsible for compliance to Part 15 of the FCC rules.

THIS IS A CLASS A PRODUCT. IN A DOMESTIC ENVIRONMENT THIS PRODUCT

MAY CAUSE RADIO INTERFERENCE IN WHICH CASE THE USER MAY BE

REQUIRED TO TAKE ADEQUATE MEASURES.

BEFORE YOU USE

■ The power cord and AC adapter that come with this product are for this product only. Do not use

them with another product.

■

Be sure to use the power cord applicable to your local power specifications.

■ When storing the product, do not leave it under direct sunlight or by heaters. It may become

discolored, deformed, or damaged.

■ Do not place this product in any humid, dusty, salt bearing wind, or vibrating locations.

Only use it under the following environmental conditions:

Temperature: 0°C - 40°C (32°F - 104°F)

Humidity: 30% - 85% (No condensation)

■ Do not move the camera column or the lamp column while your finger is being placed between the

camera column and the lamp column. Otherwise, your finger may be pinched and injured.

■ In handling (including setting up and storing) or carrying the camera, be meticulously careful not

to give an impact on the camera head.

■ Use a soft, dry cloth for cleaning.

Do not use any volatile solvent such as thinner or benzene.

■ Do not point the camera lens directly at the sun. It may be damaged and you may not be able to

take pictures.

■ Luminescent and Black Spots

There may be some pixels that do not properly operate due to the use of CMOS Area Image

Sensors made-up of many pixels.

Though luminescent or black spots may be found on the screen, it is a phenomenon peculiar to

the CMOS Area Image Sensors and is not a malfunction.

■To prevent damage during transport, a protection sheet has been put on the touch panel screen.

Please be sure to remove it before use.

Do not press the panel strongly by finger or sharp objects.

This can cause damage or malfunction.

■ Follow the guidelines below to prevent the unit from dropping or overturning.

• Use the product on a stable base, desk, or table. Do not place the product on an unstable

base or slanted surface.

• Place or wire the unit to prevent the AC adapter cord or video cable from pulling.

■ Carry the product by holding the lower part of the main unit in both hands. Never hold the

product by the column or the camera head.

■ Pay careful attention when using (including setting-up and storing) or transferring the product to

prevent the camera head from receiving any shocks.

■ Do not look directly into the LED light. If you look directly into it at point-blank range, your eyes

may be injured.

■ Some type of SD card/USB flash drive can be used.

■ Transfer the data from the SD card onto a device such as a PC to save a backup copy.

Malfunction of the product or repairs to it may cause the data saved in the SD card to be deleted.

■ If this product is used for longer than the warranty period, its performance and quality may

deteriorate due to the lifetime of its parts. To purchase replacement parts, consult the dealer from

whom you purchased this product or our branch/office near your location.

■ Battery precautions:

• If this product is not going to be used for a long time, take the batteries out of the remote

control.

• Do not use rechargeable batteries (e.g., Ni-Cd (NiCad batteries)).

• Do not use new and old batteries or batteries of different types together.

• Do not try to recharge or short-circuit the batteries.

• When disposing of used batteries, follow the instructions of your local government.

• Insert from one side and pay particular attention to the polarity (+/- directions).

• Be sure to use AAA batteries.

• If any liquid from a battery leaks onto your skin or clothes, flush the area with clean water

immediately. If it gets into your eye, flush immediately with clean water and then contact a

doctor.

• Do not burn, disassemble, change nor dispose of in fire. Doing so damages the insulation

materials which may cause heat generation, leakage, bursting or a fire.

• Do not damage nor peel off the resin film on the surface of the battery.

■ About using microphones

Connecting microphones other than electret condenser microphones (microphones for PCs and

so on) could cause a malfunction to occur. If you are concerned about this product’s operating

noise when using the built-in microphone, we recommend using an external microphone.

■ About the audio input port

Do not connect any audio line-output devices such as a CD/MP3 player to the audio input port

when the Audio Selector is set to “Mic-in.” Audio input is a dual purpose port (microphone/line-in)

which supplies power when “Mic-in” is selected, adding external output devices (CD/MP3) may

damage them.

■ About the MIC IN/ AUDIO OUT cable

Before connecting the cable with the product, attach the ferrite core that is supplied with the

product to the cable as close to the connector of the product as possible.

(Example: Looping a cable through the ferrite core 2 times)

To the connector

of the product

■ Menu / Icon

Some functions may not be set or operated depending on the mode or the menu / Icon settings

being used.

■ Record/Play

• Before recording an important scene, make sure to do a test recording to confirm that the

camera is working properly.

• The maximum file size of the continuous recording is 2GB. (The maximum recording length

varies depending on other factors such as resolution and recording quality.)

• Movie files that are recorded with this camera or converted by the proprietary software can

only be played with this camera.

• Pay attention to operation by the touch panel during recording the movie becouse a sound of

operation may be recorded.

■ Network function

This function does not guarantee the normal operation when this camera system is connected

directly to the Internet. Shut down any communication not routed via packet filter or the like in a

router or the like.

■ Copyright

Do not commercially use or transfer movies or audio files recorded with the camera without the

permission of the copyright holder except for personal use.

Do not use the camera in locations where recording movies or audio files are prohibited.

IMPORTANT SAFEGUARDS ................................................................................................................................ 2

BEFORE YOU USE................................................................................................................................................ 7

CONTENTS .......................................................................................................................................................... 11

1 BUNDLED ITEMS ........................................................................................................................................... 13

2 BASIC OPERATIONS .................................................................................................................................... 14

2-1 Document Camera ......................................................................................................................................................... 14

■Part Names ................................................................................................................................................................... 14

■Touch panel .................................................................................................................................................................. 15

■Rear panel and cable connection ................................................................................................................................. 16

■Side panel ..................................................................................................................................................................... 20

■Moving Parts of the Document Camera ....................................................................................................................... 21

2-2 Supplied Accessories ..................................................................................................................................................... 22

■Remote Control ............................................................................................................................................................. 22

■Remote Control Strap ................................................................................................................................................... 23

■Image Mate CD-ROM ................................................................................................................................................... 23

■Preparation ................................................................................................................................................................... 24

2-3 Shooting Images .......................................................................................................................................................... 27

■Setting up the main unit ................................................................................................................................................ 27

■Turning the power ON/OFF .......................................................................................................................................... 28

■Operating the touch panel ............................................................................................................................................ 29

■Adjusting the size .......................................................................................................................................................... 31

■Auto focus（AF） ......................................................................................................................................................... 31

■Adjusting the brightness ............................................................................................................................................... 32

■Turning the illumination ON/OFF .................................................................................................................................. 34

■Image selection ............................................................................................................................................................. 35

■Details of Each Function ............................................................................................................................................... 38

■Icon descriptions ........................................................................................................................................................... 45

3 ADVANCED OPERATIONS ............................................................................................................................ 62

3-1 Using an SD card/USB ﬂash drive ................................................................................................................................. 62

■Saving images .............................................................................................................................................................. 64

■Displaying the stored data ............................................................................................................................................ 69

3-2 Outputting a different image to RGB OUT and HDMI OUT ........................................................................................... 78

3-3 Saving data stored on an SD card to PC via USB cable ............................................................................................... 79

3-4 Presentation using a USB-connected PC with the supplied software ........................................................................... 81

3-5 Displaying the Video Image through Network Connection ............................................................................................ 83

3-6 Using [MIC IN] and [AUDIO IN] ...................................................................................................................................... 88

3-7 Using the ELMO Wireless Slate/Tablet (CRA-1) with the equipment ............................................................................ 89

■Connecting the ELMO Wireless Slate/Tablet (CRA-1) ................................................................................................. 89

■Basic operations ........................................................................................................................................................... 90

■Selecting how to use the pen tablet from the tablet menu ........................................................................................... 92

■Writing to camera images ............................................................................................................................................. 93

■Using as a whiteboard .................................................................................................................................................. 97

■Using the SD card ......................................................................................................................................................... 99

3-8 Shooting off the stage .................................................................................................................................................. 105

3-9 About RS-232C ............................................................................................................................................................ 106

4 TROUBLE SHOOTING ................................................................................................................................. 107

4-1 Symptoms and Confirmation ........................................................................................................................................ 107

5 SPECIFICATIONS ........................................................................................................................................ 111

5-1 General ......................................................................................................................................................................... 111

5-2 Main Camera ................................................................................................................................................................ 11 2

5-3 Illumination Device ....................................................................................................................................................... 11 3

5-4 Trademarks and License .............................................................................................................................................. 114

dealer from

USB cable

AAA batteries

Image Mate/Instruction

LAN cable

Ferrite core

Warranty IMPORTANT

Image Mate

P21

P23

P22

Strap

1 1 BUNDLED ITEMS

The items below are included with this product. If any item is missing, contact the

whom you purchased this product.

(for Remote control)

AC adapter

Document camera

P27

AC cord

P27

RGB cable

(for Remote control)

P17

P22

Remote control

P18

(for Connecting to PC)

P23

Manual CD-ROM

Installation Manual

P18

(for Mic IN / AUDIO OUT cable)

P18

P20

(US/JAPAN Only )

SAFEGUARDS

P21

P34

P22

P20

P29

P28

P16

P34

Front

Rear/Side

2 2 BASIC OPERATIONS

2-1 Document Camera

■Part Names

Operation of the main unit:

②

④

①

⑧

Name

①

②

③

④

⑤

⑥

Upper light

Remote control sensor

Side panel

Built-in mic

Touch panel

Main switch

⑤

③

⑥

②

⑦

⑧

Rear panel

Base light

P29

■Touch panel

Name Function

Output image and icons are displayed. With these

icons, various settings can be made.

①

Touch panel

CAUTION

• Do not press the panel strongly by finger or sharp objects.

This can cause damage or malfunction.

• To prevent damage during transport, a protection sheet has been put on the touch

panel screen. Please be sure to remove it before use.

The touch panel is made of glass. Pay attention to the followings to avoid

glass breakage and injury.

• Do not rub or press the panel with a sharp object such as a knife.

• Do not press the panel strongly by finger or do not apply weight to the panel.

• Do not rub the panel with a hard object.

• Do not hit the panel with a hard object or do not drop it onto the panel.

• Do not put an object on the panel.

• Gently wipe the surface with a soft cloth to remove dirt.

Pay attention to the followings in order to maintain the performance of the

touch panel.

• Do not stick adhesive tape on the panel.

• A protection sheet is attached to the surface of the touch panel to avoid

scratches during transportation. Remove the sheet gently before use.

■Rear panel and cable connection

①

④ ③ ② ③ ②

⑩ ⑪ ⑨

⑧

⑦

Name Function

①

②

③

④

HDMI IN 1

HDMI IN 2

RGB IN 1

RGB IN 2

AUDIO IN 1

AUDIO IN 2

Resolution

To input HDMI images and audio. (HDMI cable is not supplied

with the product.)

To input RGB image. (RGB cable is supplied with this product.)

In the stand-by mode, the image input to the [RGB IN 1] terminal

is output from the [RGB OUT] terminal.

To input audio line .(An audio cable is not supplied with this

product.)

To change the display resolution of output terminal.

Select the display resolution with the switch.

Resolution

1080P（1920 × 1080）

720P（1280 × 720）

Left

switch

⑥

⑤

Right

switch

Ethernet terminal

⑤

[100BASE/10BASE]

SXGA（1280 × 1024）

WXGA（1280 × 800）

XGA（1024 × 768）

To enable the image transfer or the main unit control over the

LAN. (LAN cable is supplied with this product.)

N o t e

DSUB 15P shrink terminal

Name Function

USB To connect to a PC. (USB cable is supplied with this product.)

⑥

⑦

⑧

⑨

⑩

⑪

RS-232C

AUDIO OUT To output audio line. (Audio cable is not supplied with this product.)

RGB OUT

HDMI OUT

DC IN 12V Plug-in for the AC adapter. (A cable is supplied with this product.)

To control the unit from a PC through an RS-232C cable.

(RS-232C cable is not supplied with this product.)

To output analog RGB images. (Analog RGB cable is supplied with

this product.)

To output digital images. (HDMI cable is not supplied with this

product.)

① To connect the product to a device with an HDMI output terminal.

Connect a commercially available HDMI cable to the [HDMI IN] terminal on the rear panel.

• Cable must conform to the HDMI standard.

• Elmo does not guarantee operation for all HDMI-compatible monitors.

② To connect the product to a device with an analog RGB output terminal.

Connect the RGB cable to the [RGB IN] terminal on the rear panel.

Only 1 RGB cable is supplied with the product.

■Speciﬁcations of the [RGB IN] terminal

Signal allocation

Video signal Analog 0.7V (p-p) 75Ω terminated

Horizontal synchronized signal TTL level (Positive/negative polarity)

Vertical synchronized signal TTL level (Positive/negative polarity)

synchronized signal

Pin No. Name Pin No. Name Pin No. Name

1 Video signal (Red) ６ GND (Red) １１ GND

2 Video signal (Green) ７ GND (Green) １２ N.C

3 Video signal (Blue) ８ GND (Blue) １３

4 N.C ９ N.C １４

5 GND １０ GND １５ N.C

Horizontal

Vertical

synchronized signal

③ To connect the unit to a device (audio amplifier etc) with an audio line output

terminal.

Connect a commercially available audio cable to the [AUDIO IN] terminal on the rear panel.

④ To switch the output image type.

Change the output image type.

⑤ To connect the unit to a device with Ethernet terminal.

Connect the supplied LAN cable to the [Ethernet terminal] terminal on the rear panel.

Explanation of the Ethernet terminal LED

Orange…Blinking: Access

Green … ON: Link OK

⑥ To connect a PC with the USB cable.

Connect the supplied USB cable to the [USB] terminal on the rear panel.

⑦ To connect the unit to a device with an RS-232C port.

The unit can be controlled from a PC through an RS-232C cable by using [RS-232C] terminal on

the rear panel.

⑧ To connect the unit to a device (speaker with amplifier etc) with an audio line

input terminal.

Connect a commercially available audio cable to the [AUDIO OUT] terminal on the rear panel

after looping the audio cable 2 times around the ferrite core that is supplied with this product.

⑨ To connect the unit to a device with an analog RGB input terminal.

Connect the RGB cable to the [RGB OUT] terminal on the rear panel.

Only 1 RGB cable is supplied with the product.

N o t e

⑩ To connect the unit to a device with an HDMI input terminal.

Connect a commercially available HDMI cable to the [HDMI OUT] terminal on the rear

panel.

• Please use the monitor corresponding to the input of the image (resolution) or 720p or more.

It will not operate with a cable that doesn’t conform to the HDMI standard.

• Elmo does not guarantee operation for all HDMI-compatible monitors.

⑪ To connect the AC adapter.

Before inserting the AC adapter in an outlet, connect the DC plug of the supplied AC adapter to

the [DC IN 12V] terminal on the rear panel.

• If the displayed image is off-center, adjustment of the horizontal and vertical position should be

made from the connected device.

• In some cases, vertical stripes may appear on the display device. This can be reduced by

adjusting the “clock phase” function of the connected device.

• When using a PC with external output mode switching, tap [ (Signal select)] > [ ]

on the touch panel after setting the PC to the external output mode.

•

When selecting the image in [ Signal select (Normal)], output same image (resolution) to

[RGB OUT] and [HDMI OUT].

• When the HDMI monitor is connected, the output image (resolution) is automatically changed

based on information from the connected monitor. Even if [RGB OUT] is selected, it is not

reﬂected.

• We recommend that you change the output image (resolution) with the power supply turned off

(standby status).

We do not guarantee proper operation when the output image (resolution) was changed in any

other condition than speciﬁed above.

• We recommend using a USB 2.0 compliant USB cable.

• If you plug into the USB cable with the power on, the PC may not recognize the device.

• Depending on the PC’s USB environment or the peripheral equipment using the USB 2.0

compliant cable, image transfer may be disrupted.

• Operation is not guaranteed for all environments.

N o t e

and so on) could cause a malfunction to occur.

P89

P62

■Side panel

Mark Function

①

②

③

④

MIC IN

MIC OUT

①

②

③

④

To insert an SD card (commercially available).

Push the card again to remove the SD card.

To connect a wireless pen Tablet (commercially available) or a

USB flash drive (commercially available).

To connect an audio line-output device after looping the cable 3 times

around the ferrite core that is supplied with this product. Audio input is a

dual purpose port (microphone/line-in). When using a microphone, make

sure to connect a commercially available electret condenser microphone.

To output audio signal input to the “MIC IN” terminal. (An audio cable is not

supplied with this product.)

• Connecting microphones other than electret condenser microphones (microphones for PCs

■Moving Parts of the Document Camera

This unit can be moved as shown below.

WARNING

Children may ingest small batteries;

always keep batteries safe and out

of reach.

If a battery is swallowed, consult

a doctor immediately as this could

result in asphyxiation or be an

obstacle to digestion, etc.

N o t e

relocate the main unit or shield the light source.

P31

P62

2-2 Supplied Accessories

■Remote Control

Preparation of Remote Control

Remove the battery case cover at the back of the remote control and install 2 batteries. (TYPE

AAA)

Operation of the remote control

When a camera image is displayed

When data in an SD card/USB ﬂash drive is displayed

Receiving signal from the remote control

Point the infrared light emitting part of the remote control at the infrared

sensor, and press the button of the desired function.

Receivable range

Distance: Within approx. 7m from the front of the infrared

sensor

Angle: Within 30° up, down, left, and right of the infrared

sensor

Within 7m

The receivable range may be reduced when the main

unit is placed in direct sunlight, near an inverter

ﬂuorescent light or in any other unfavorable conditions.

Depending on the light source conditions, the sensor

may fail to receive any infrared light. In such cases,

sensor

■Remote Control Strap

The strap can be fastened to the remote control as shown below.

■Image Mate CD-ROM

The CD-ROM contains the software for connecting to a PC and the Instruction Manual. For

software installation, follow the instructions of the Image Mate Installation Manual.

N o t e

Locked

Unlock

③

■Preparation

Setting Up

① Release the camera column lock by turning the security lock knob.

② As shown in the right figure, hold the setup grip

and raise the camera column. At this time, the camera

head slides up in conjunction with the rise of the camera

column. The lamp column will also rise.

③ If necessary, move the lamp column and the lamp head

to an appropriate position as shown in the right figure.

Setup grip

When using a glossy paper, the document could reflect the

illumination to disable normal display. In this case, adjust the

lamp position to a position in which such reflection can be

avoided.

N o t e

If the camera column is pulled or pushed forcedly, the camera

might be pushed out of position, and the camera image might

be displaced from the display center. In this case, initialize the

camera position as follows:

(1) Fold the camera column on the stage. When the camera

column is folded in the storage position, the camera

position is initialized.

(2)Then, raise the camera column.

Setup grip

N o t e

STORING

①Return the lamp to the original position. Then,

hold the setup grip of the camera column and fold

the camera column. At this time, the camera head

slides down and the lamp column also folds.

Turn OFF the power switch before the storing.

②Lock the camera column and the lamp column by

turning the security lock.

Do not force down the camera column

and the lamp column when folding them.

②

Locked

Do not fold the camera column when the

close-up lens holder remains open, or the

close-up lens could be damaged.

Unlocked

When this camera system is not in use,

unplug the power cord and the AC adapter

from the plug socket.

Close-up

lens holder

P28

2-3 Shooting Images

AC cord

AC adapter

Camera

Power button

Cable

■Setting up the main unit

Set up the main unit as shown in the figure above. Then connect the main unit to a projector or a

PC monitor, and turn on the power of the main unit.

Connecting the AC cord

Connect the AC cord and the AC adapter. Then connect the AC adapter to the [ DC IN 12V ]

terminal at the rear panel of the document camera, and insert the AC cord into an outlet.

AC adapter

To main unit

To wall outlet

Connect

AC cord

N o t e

Connecting the video cable

Connect the document camera to the display device with a video cable corresponding to the

display device.

CAUTION

Before connecting the main unit to other devices, be sure to turn OFF the

power for all of the devices.

Set the resolution corresponding to the display device.

■Turning the power ON/OFF

• Press the [ ] button on the main unit or the [ ]

button on the remote control to turn the power ON.

(After the [ ] button ﬂashes blue, it is illuminated a few

seconds later.)

• Press the [ ] button on the main unit or the [ ]

button on the remote control to turn the power OFF.

You need to hold down the button for two seconds or more for

the button on the main unit.

(The LED of the [ ] button is illuminated in red.)

• Do not operate this device while it is ﬂashing.

■Operating the touch panel

You can control the unit with the touch panel..

Startup screen

The startup screen will appear on the touch panel

when the product is turned on.

Main menu

The main menu is displayed by tapping the menu

icon at the top right of the startup screen

How to operate the touch panel

① Tap

By tapping an icon on the touch panel,

you can select a function and operate.

N o t e

② Drag

By sliding your finger across the touch panel

surface while touching the item, you can move it.

When the Presentation features (Highlight, Mask,

Scroll) are in use, you can move the area.

The touch panel in the P100HD is a “Resistive Touchscreen” which is different than

“Capacitive Touchscreen” typically found in consumer tablets. To operate, firmly press a

selected icon or drag a selected area to initiate a command.

CAUTION

• To prevent damage during transport, a protection sheet has been put on the touch panel

screen. Please be sure to remove it before use.

• Do not press the panel strongly by finger or sharp objects.

This can cause damage or malfunction.

• Please do not put a thing on a screen.

N o t e

■Adjusting the size

To adjust the display area of the document, tap [Startup screen] > [ / ] on the touch

panel or press the [ / ] button on the remote control.

ZOOM-IN

: The object can be shown in large size.

ZOOM-OUT

: The object can be shown in small size.

• Zoom ratio: Optical 16x, Digital 8x

• When the optical zoom reaches 16x, it automatically shifts to digital zoom.

• Within the digital zoom range, the image quality is degraded.

• ON/OFF of the digital zoom can be set from the setting menu.

• When you choose the external input in Signal select, you can not operate to zoom.

■AF（Auto focus）

( [ (Setting)] > [ (AF mode)] > [ ] on the touch panel )

To auto focus only once when [Startup screen] > the image area on the touch panel or the [ ]

button on the remote control is pressed.

■Adjusting the brightness

To adjust the brightness of the image, tap [ (Main menu)] > [ ] on the touch

panel or press the [ / ] buttons on the remote control.

The following two adjustment modes are available for this adjustment. Each mode can be set by

tapping [ (Setting) ] > [ ] on the touch panel.

Automatic brightness adjustment

([ (Setting)] >[ (Brightness)] > [ ] on the touch panel )

To ensure a constant degree of brightness, the brightness of the image changes automatically

according to the brightness

of the shooting environment. Tap [ (Main menu)] > [ ] or press the

[ / ] buttons on the remote control to change the level of the automatic brightness

adjustment.

Brightness of the screen is the same

N o t e

Manual brightness adjustment

( [ (Setting)] > [ (Brightness)] > [ ] on the touch panel )

To change the brightness manually, tap [ (Main menu)] > [ ] or press the

[ / ] buttons on the remote control. The image brightness does not automatically

change in response to the brightness of the shooting environment.

• Factory setting is set to [Auto].

•To return to the factory settings, tap [ (Main menu)] > [ ] on the touch

panel.

• In places where the object is exposed to bright sunlight (e.g. near a window), or extremely

bright lights, the brightness of the screen may not dim sufficiently, even by tapping

[ (Main menu)] > [ ] or pressing the [ ] button on the remote control.

In such cases, close the curtains or move the object away from the light to adjust the amount

of light.

• When you choose the external input in Signal select, you can not adjust the brightness.

Brightness of the screen is different

■Turning the illumination ON/OFF

Upper light

Base light

The upper light and the base light can be turned ON/OFF by tapping [ (Main menu)] >

[ ] [ ] on the touch panel.

CAUTION

• When you take a picture of a person, turn off the upper light.

• Make sure that the light from the upper light does not shine directly into your eyes.

• This product is equipped with a high-brightness LED light. You can safely use the light to light

up objects, however its brightness will gradually diminish with long-term use. This is not a

malfunction of the light, but a feature of LED performance.

• Do not touch the upper light while it is on as it may become very hot.

N o t e

■Image selection

You can switch the input source either with the remote control or from the Signal select screen

displayed by tapping [ (Main menu)] > [ ] on the touch panel.

Camera image:

[ (Signal select)] > [ ] on the touch panel

[ ] button on the remote control

Image input from the

RGB IN1、RGB IN2、HDMI IN1、HDMI IN2 terminal:

[ (Signal select)] > [ ] on the touch panel

[ ] button on the remote control.（Only RGB IN1 is selected.）

Image stored on the SD card/USB ﬂash drive:

[ (Signal select)] > [ ] on the touch panel

[ ] button on the remote control

• When using a PC with external output mode switching, set it using the following

procedures.

1. Connect the PC to this unit.

2. Change the PC to the external output mode.

3. Tap [ (Signal select)] > [ ] on the touch panel or pressing the [ ]

button on the remote control.

•

When selecting the image in [ Signal select (Normal)], output same image (resolution)

to [RGB OUT] and [HDMI OUT].

• When selecting external input image, do not change the resolution of the input image.

The following image signals can be input to the RGB input terminal.

The image signals specified as "Video" in the following table can be input to the HDMI input

terminal.

Polarity of synchronized

Resolution

（dot）

Horizontal （kHz） Vertical (Hz) HS/VS

640×480 31.469 59.940 N/N VESA

800×600 37.879 60.317 P/P VESA

1024×768 48.363 60.004 N/N VESA

1280×800 49.702 59.810 N/P VESA

1280×1024 63.981 60.020 P/P VESA

480p 31.500 60.000 N/N Video

576p 31.250 50.000 N/N Video

Frequency

signal

(P: Positive, N: Negative)

Standard

720p 37.500 50.000 P/P Video

720p 45.000 60.000 P/P Video

1080p 56.250 50.000 P/P Video

1080p 67.500 60.000 P/P Video

N o t e

■Details of Each Function

Highlight Function

This is a function to highlight a particular section of the image.

Use this function to draw attention to a section.

Highlight operations

When you tap [ (Presentation)] > [ ] on the touch panel

or the [ ] button on the remote control while the camera image、

the external input or the still image is displayed, the highlight

function works with the darkness and size set previously.

You can move the highlighted area by dragging it on the touch

panel or with [ ] buttons on the remote control.

The highlight function is released by tapping [Highlight] >

[ ] on the touch panel or by pressing the [ ]

button on the remote control again.

• Highlighted image cannot be captured.

Setting operations

You can change the darkness of the highlighted

area by tapping [Highlight] > [ ] [ ]

while the highlight function is activated.

Also, by dragging the edge of the highlighted

area on the touch panel, you can change the

size of the highlighted area.

N o t e

Mask Function

This is a function to mask a section of an image.

Mask operations

When you tap [ (Presentation)] > [ ] on the touch panel

or the [ ] button on the remote control while the camera image

or the external input or the still image is displayed, the mask effect

is applied with the darkness set previously.

You can move the masked area by dragging it on the touch

panel or with [ ] buttons on the remote control.

The mask function is released by tapping [Mask] > [ ]

on the touch panel or by pressing the [ ] button on

the remote control again.

• Masked image cannot be captured.

N o t e

Normal

Scroll Function

The image expands to the digital zoom set previously, and the enlarged screen can be scrolled.

Scroll operations

When you tap [ (Presentation)] > [ ] on the touch panel

or the [ ] button on the remote control while the camera image

or the still image is displayed, the digital zoom works with the

magnification set previously.

You can scroll the enlarged image by dragging the scroll area

on the touch panel or with [ ] buttons on the remote control.

The digital zoom is released by tapping [Scroll] > [ ] on the

touch panel or by pressing the [ ] button on the remote control again.

• When digital zoom has already been performed from the [Startup screen] > [ / ]

on the touch panel or zoom buttons on the remote control, digital zoom is released and the

scroll function works at the magnification ratio currently set.

• Zoom cannot be used while scrolling.

• Digital zoom may cause image quality deteriorates.

Digital zoom

Scroll

Digital zoom setting operations

You can change the digital zoom ratio to either x2, x3, or x4 by

tapping [Scroll] > [ ][ ], or [ ] on the touch panel

while the scroll function is working.

Picture or External Input

Compare Picture Function

To display the live camera image and a picture stored on the SD card/USB flash drive together.

Compare Picture operations

When operating by the touch panel

Tap the touch panel [ (Presentation)] >

[ ] to display the Input signal select screen.

Tap the [ ] to display the input source.

Left side of the screen : Camera image

Right side of the screen : Selected input source [ ] [ ] [ ] or [ ]

Also the following information will be displayed if [ ] is tapped:

Left side of the screen : Camera image

Right side of the screen : Still images that are stored in the USB memory or the SD card

When operating by the remote control

When the camera image is displayed, press the [ ] button on the remote control to display

the input source.

Left side of the screen : Camera image

Right side of the screen : RGB 1

Also the following information will be displayed if the [ ] button on the remote control is

pressed while a still picture is displayed:

Left side of the screen : Camera image

Right side of the screen : Still images that are stored in the USB memory or the SD card

Camera image

N o t e

Picture

Operating the camera image

When you tap [Compare picture] > [ / ]

on the touch panel or the [ / ]

button on the remote control while the Compare

picture function is working, you can adjust the

display area of the document.

When setting manual in the AF mode, tap the part

except the icon on the screen left side to adjust

the focus.

Changing the still image

You can change the still image displayed on the

screen to other still image stored on the SD card

/USB flash drive by tapping [Compare Picture] >

[ ] [ ] on the touch panel or pressing

[ / ] buttons on the remote control

while the Compare Picture function is working.

Releasing compare pictures function

Camera image

Tap the touch panel [Compare picture] > [ ] or press the [ ] button on the remote

control again. The compare picture function is released.

• When using the Compare Picture function, the image cannot be captured.

N o t e

Mosaic Function

To apply a mosaic effect to the image. You can change the extent of mosaic.

Mosaic Operations

When you tap [ (Presentation)] > [ ] on the touch panel while the camera image,

the external input or the still image is displayed, the mosaic effect is applied.

The mosaic effect is released by tapping [Mosaic] > [ ] on the touch panel

Mosaic setting Operations

You can change the degree of mosaic by tapping

[Mosaic] > [ ] [ ] on the touch panel

while the mosaic function is working.

• When using the Mosaic function, the image cannot be captured.

■Icon descriptions

Startup screen

Icon Name Function

Zoom In Object can be shown in larger size.

Zoom Out Object can be shown in smaller size.

Screen

Menu Move to Main menu.

Focus on the image when tapped while the AF mode is set to

manual.

Main menu

Icon Name Function

Main menu Display the operation menu for camera image.

Presentation Display the Presentation screen.

Signal select

Setting Display the Setting screen.

Display the Signal select screen.

※ Normal settings and Advanced settings are available.

Capture Save the still image on the SD card/USB ﬂash drive.

Rec Save the video on the SD card/USB ﬂash drive.

Pause Pause the camera image. Press this button again to restart.

Adjust Brightness Adjust brightness the camera image.

Reset Brightness Return to the factory settings of brightness.

Lighting switch

Preview Return to the Start-up screen when tapped.

Turn ON/OFF of the material illumination or the base

illumination .

Presentation

Icon Name Function

Highlight Highlight part of the image you want to emphasize.

Mask Mask part of the image.

Scroll

Compare Picture

Enlarge the image to the size you specify, allowing you to move

within the enlarged area.

Display the live image and the still image or image from the

external input together. Display the Compare Picture Input

Settings screen.

Mosaic Apply mosaic effect to the image.

Image Rotation Rotate camera image by 180°.

Color/B&W Display an image in color or black & white.

Posi / Nega Output a positive or negative image.

Presentation Settings

Highlight

②

Icon Name Function

②

①

②

①

②

Highlighted area Move the Highlighted area by dragging.

Change the size of the Highlighted area by dragging the outside

Around the Highlighted area

of the highlighted area.

Darken Make the dark area less transparent and harder to see through.

Lighten Make the dark area more transparent and easier to see through.

Exit Return to the Presentation screen.

Mask

Icon･Area Name Function

① Mask area Move the Mask area by dragging.

①

Exit Return to the Presentation screen.

Scroll

Icon･Area Name Function

① Enlargement Scroll the enlarged area by dragging.

①

Magnification setting Set the digital zoom magniﬁcation to ×2 ,×3 or ×4.

Exit Return to the Presentation screen.

Compare Picture Input Settings

Icon Name Function

Camera image/External

input

Camera image/still image Compare the camera image and the still image.

Compare the camera image and the image from the

external input.

External input selection

Exit Return to the Presentation screen.

Select the external input to compare with the camera

image.

Compare Picture

Icon /Area Name Function

Zoom In Object can be shown in large size.

Zoom Out Object can be shown in small size.

Screen

Prev Picture

Next Picture

Exit Return to the Compare Picture Input Settings screen

Focus on the image when tapped while the AF mode is set

to manual.

Show the previous picture. This icon is only shown during

comparing still image.

Show the next picture. This icon is only shown during

comparing still image.

Mosaic

Icon Name Function

Coarse Make the mosaic pattern coarser.

Fine Make the mosaic pattern ﬁner.

Exit Return to the Presentation screen.

Image Rotation

Icon Name Function

Image Rotation Rotate a camera image by 180°.

Exit Return to the Presentation screen.

Color/B&W

Icon Name Function

Color/B&W Display an image in color or black & white.

Exit Return to the Presentation screen.

Posi/Nega

Icon Name Function

Posi/Nega Output a positive or negative image.

Exit Return to the Presentation screen.

Signal select (Normal)

Icon Name Function

Advance mode Move to the Advance mode.

Camera Select the camera image.

Thumbnail Select the thumbnail.

External input

Signal select (Advance)

Icon Name Function

Select the external input. Same image is output to RGB

output and HDMI output. You can not select the Advance

mode while selecting the external input.

Normal Return to the normal mode.

Select the external input that you want to output

External input

from RGB output. When this is selected, the camera image is output from HDMI output.

Setting

Tap the icon that want to set.

Icon Name Function

Prev Page Move to the previous page.

Next Page Move to the next page.

Brightness

Icon Name Default Function

Maintain constant brightness of the image, the brightness of the

image changes automatically according to the brightness of the

shooting environment. Tap [ (Main menu)] > [ ] on

Auto

ﾚ

the touch panel or press the [ / ] buttons on the remote

control to change the level of the automatic brightness adjustment.

To change the brightness manually, tap [ (Main menu)] >

[ ] on the touch panel or press the [ / ] buttons on

Manual

Exit Return to the Setting screen.

the remote control. The image brightness does not automatically

change in response to the brightness of the shooting environment.

★ What is AF?

AF Mode

A function to automatically focus the camera.

Icon Name Default Function

Focus automatically. You do not need to tap the touch panel or press

Auto

Manual

Zoom Sync Auto focus only once after zooming.

Exit Return to the Setting screen.

the [ ] button on the remote control. The focus changes

automatically as the object changes.

De-activate the auto focus once when tapped or the [ ] button

ﾚ

on the remote control is pressed.

Focus

Icon Name Function

Near

Focus manually.

Far

Exit Return to the Setting screen.

★ What is White Balance?

A function to adjust any area of white color and ensure it is projected

accurately as white. This allows colors to be seen naturally according to the

White Balance

characteristics of the object.

Icon Name Default Function

Adjust the white balance automatically. The white balance is adjusted

Auto

Manual Manually adjust the [R-Gain] and the [B-Gain].

automatically to ensure a more natural color according to the

ﾚ

characteristics of the object.

One-Push

Exit Return to the Setting screen.

Automatically adjust the white balance only once when this setting is

selected.

R-Gain

Icon Name Function

To adjust the R-Gain of the camera image when the white balance is set to

Manual. Use [Up] or [Down] to increase or decrease the red color.

Down

Exit Return to the Setting screen.

B-Gain

Icon Name Function

To adjust the B-Gain of the camera image when the white balance is set to

Manual. Use [Up] or [Down] to increase or decrease the blue color.

Down

Exit Return to the Setting screen.

Digital Zoom

Icon Name Default Function

Valid

Invalid

Exit Return to the Setting screen.

ﾚ

Set the digital zoom to Valid/Invalid.

★ What is Image Mode?

A special effect to project a clear image.

Image Mode

Icon Name Default Function

Text1

Text2

Text3

Graphic1 Clearly reproduce photographs and color documents.

Graphic2

Exit Return to the Setting screen.

ﾚ

Clearly reproduce black & white documents including such features as

characters and lines. The effect intensiﬁes as the number increases.

Image could be improved if used with a DLP projector.

(The effect depends on the projector used.)

Edge Effect

Icon Name Default Function

Low

Medium

High

Exit Return to the Setting screen.

ﾚ

Emphasize the outline of images.

Enabled only when [Graphic1] is selected for the Image Mode

★ What is Gamma?

An image characteristic unique to image I/O devices.

Gamma

Icon Name Default Function

Low

Change the characteristics of the image.

Medium

High

Exit Return to the Setting screen.

ﾚ

Enabled only when [Graphic1] is selected for the

Image Mode.

Flicker Rate

Icon Name Default Function

50Hz Others

60Hz Japan/U.S.

Exit

Reduce ﬂuorescent light ﬂickering due to the power supply frequency.

Select the same value as used for the power supply frequency.

Return to the Setting screen.

Movie Quality

Icon Name Default Function

Low

Medium

High

Exit Return to the Setting screen.

Set the quality of the movie to record.

ﾚ

★What is USB Mode?

Functions described below can be used by connecting the

USB Mode

document camera to a PC with the USB cable.

Icon Name Default Function

Mass Storage Send the data on the SD card loaded in the device to the PC.

Application

Exit Return to the Setting screen.

Control this device from a PC using special software.

ﾚ

Select Memory

Icon Name Default Function

SD Card

USB Flash

Drive

Exit Return to the Setting screen.

ﾚ

Select where to save still images/movies, when both SD card and

USB ﬂ ash drive are inserted.

Language

Icon Name Default Function

Japanese Japan Display the menu in Japanese.

English Others Display the menu in English.

Exit Return to the Setting screen.

Volume

Icon Name Function

Set the volume of the audio line output and the HDMI output.

Down

Exit Return to the Setting screen.

Audio Selector

Icon Name Default Function

Built-in mic

Mic-in

Line-in

Exit Return to the Setting screen.

ﾚ

Select the source of the audio input.

Mic Mixer

Icon Name Default Function

ON Mix MIC IN with AUDIO IN of the back panel to output AUDIO OUT.

OFF

Exit Return to the Setting screen.

Output the signal input from AUDIO IN in the back panel from AUDIO

ﾚ

OUT.

Reset All

Icon Name Function

Yes Reset various settings to factory settings.

Exit Return to the Setting screen.

★Saved Items

Zoom, Brightness, Mode, Brightness Level, White Balance,

Save Presets

R-Gain, B-Gain,

Icon Name Function

１

２

３

Exit Return to the Setting screen.

Save the current setting as the preset setting of the selected number.

Load Presets

Icon Name Function

１

２

３

Exit Return to the Setting screen.

Call the setting saved for the selected number.

Guide

Icon Name Default Function

OFF

Exit Return to the Setting screen.

Display device’s operating status and an explanation of the icons on

ﾚ

the screen.

Turn off display of device’s operating status and an explanation of

icons on the screen.

Clock Set

Icon Name Function

Exit Return to the setting screen after setting the date and time.

Move the arrow by tapping just above year, month, day, hour, minute or

second that you want to change. Then tap the arrow to change the value..

Startup menu display

Icon Name Default Function

OFF Display the Main menu icon only on the startup screen.

Exit Return to the Setting screen.

Display the menu on the startup screen.

ﾚ

３

N o t e

3 ADVANCED OPERATIONS

3-1 Using an SD card/USB ﬂash drive

With this equipment, you can save a camera image as a picture or movie on an SD card or USB

ﬂash drive.

You can also display the data stored on the SD card or USB ﬂash drive on the screen. Before you begin, insert a commercially available SD card or USB ﬂash drive into the

corresponding slot on the side panel.

• SD card

- A SDXC card cannot be used.

- Formatting the SD card with this product before you use is recommended.

- Using an SD card to record movies is recommended.

- Using an SD card class 6 or higher is recommended.

• USB ﬂash drive

- Supports USB ﬂash drive up to 32GB.

- Formatting the USB ﬂash drive with this product before you use is recommended.

• It may take some time to recognize the memory card after inserting it or to save images to

the memory card.

• Please do not remove the memory card while recording, playing or using education support

function when the main unit is accessing the memory card.

N o t e

• Formatting the SD card/USB ﬂash drive.

When you need to format the SD card/USB ﬂ ash drive, insert it into this product and excute

formatting.

①Tap [ (Signal select)] > ［］ on the touch panel to switch the output image to

the Playback image.

②Tap [ ] located in the right of the menu to change the thumbnail icon. Then select

[ ] .

③Tap ［］to start formatting. If you do not want to format, select ［］.

■Saving images

Picture

Basic operations

When operating by the touch panel

① Tap the [ (Main menu)] >

［］ on the touch panel.

② Saving begins when [ ]

appears on the preview screen of

the touch panel.

When operating by the remote control

① Press the [ ] button on the remote control.

② Press the [ ] button on the remote control.

③ Saving begins when [ ] appears

on the screen.

- Saving -

Movie

Basic operations

When operating by the touch panel

① Tap [ (Main menu)] > ［］ to

switch to the recording screen.

② Tap [Recording] > [ ] to stop the recording.

When operating by the remote control

① Press the [ ] button on the remote control.

② Press the [ ] button on the remote control.

N o t e

③ Recording begins when [ ] appears at the top left

of the screen. When you press the [ ] button again

on the remote control, recording stops and [ ]

disappear.

• Even if the output image is set to HDMI and the resolution is set to 1080p, video is recorded in

720p.

• To prevent deterioration of image quality , use a memory card with a faster read/write speed

(SD card: Class 6 or better).

• How to select the destination to save when both SD card and USB ﬂash drive are inserted.

Tap [ (Setting)] > [ ] > [ ] [ ] on the touch panel to

select [SD Card] or [USB Flash Drive].

- Recording -

Recording display

Icon Name Function

Zoom In

Object can be shown in large size.

This icon is not shown when selecting the external input in the Signal select.

Object can be shown in small size.

Zoom Out

This icon is not shown when selecting the external input in the Signal select.

Focus on the image when tapped while the AF mode is set to manual.

Screen

This icon is not shown when selecting the external input in the Signal select.

Adjust brightness the camera image.

Adjust Brightness

This icon is not shown when selecting the external input in the Signal select.

Stop Return to the Main menu after stopping recording.

■Displaying the stored data

Thumbnail display (list of pictures/movies)

Basic operations

When operating by the touch panel

①Tap [ (Signal select)] > [ ] on the touch panel to display the thumbnails.

In the thumbnail icon,

If [ ] is selected, the list of pictures.

If [ ] is selected, the list of recorded movies appears.

② Select the picture/movie you want to display full-screen.

(1)Tap the thumbnail of the touch panel to move the cursor.

Thumbnail icon

(2) Tap the selected thumbnail again to display the picture/movie full-screen. The movie

automatically starts to play.

SD/Picture

Picture

Movie

(3) Tap [Thumbnails] > [ ][ ] to move between thumbnail pages.

③To return to the thumbnail display, tap the [ ] on the touch panel.

When operating by the remote control

①Press the [ ] button on the remote control to display the thumbnails (list of pictures/movies).

The current selection is displayed in the right bottom of the screen.

< Thumbnail images >

001/003

Press the [ ] button on the remote control to navigate the list of pictures and movies.

SD/Picture

②Select the picture/movie you want to display full-screen.

Press the [ ] button on the remote control to move the cursor.

< Thumbnail images >

001/003

③Select the picture/movie to display full-screen.

Press the [ ] button on the remote control to display the selected picture/movie full-screen.

The movie automatically starts to play.

Press the [ ] button on the remote control to display another image in the

thumbnail list.

< Thumbnail images >

SD/Picture

001/003

<Full-screen picture>

④To return to the thumbnail display, press the [ ] button on the remote control.

<Full-screen picture>

< Thumbnail images >

SD/Picture

001/003

Changing settings

Tap the thumbnail icon to change the settings.

If you tap [ ] [ ] , the next set of icons appears.

CAUTION

You can not operate the menu from the remote control.

Thumbnail icon

Icon descriptions

Thumbnail display1

Icon Name Function

Prev Page Move to the previous thumbnail page.

Next Page Move to the next thumbnail page.

Move the cursor by tapping the thumbnail which you want to

Thumbnail cursor

choose.

Move to the Picture display / Movie play screen when the

Thumbnail

thumbnail of the selected picture / movie is tapped.

Switch between the memory from which images are

SD Card

displayed.

It can be switched with the [ ] button on the remote

USB Flash Drive

control too.

Switch the data displayed as thumbnails between movies and

Picture

pictures.

It can be switched with the [ ] button on the remote

Movie

control too.

Next Menu Move to the next menu page.

Exit Return to Signal select.

Thumbnail display2

Icon Name Function

Lock (set as protected) or unlock (set as unprotected) the selected

Delete

Lock/Unlock

image.

Can be switched with the [ ] button on the remote control as

well.

Lock All Lock (set as protected) all thumbnail images.

Unlock All Unlock (set as unprotected) all thumbnail images.

Delete Move to Delete screen.

Format Move to Format screen.

Prev Menu Move to the previous menu page.

Exit Return to Signal select.

Icon Name Function

Yes Delete the selected image.

Exit Return to thumbnail display.

N o t e

Format

Icon Name Function

Yes Format the USB ﬂash drive or SD card.

Exit Return to thumbnail display.

Picture Display Menu

Icon Name Function

Prev Picture Move to the next picture page.

The icons disappear after about ten seconds from showing

the display. If you want to operate the icons, you will tap

any place on the screen. The icons show again.

Next Picture Move to the prev picture page.

Thumbnail Return to thumbnail display.

Delete Move to Delete screen.

Lock (set as protected) or unlock (set as unprotected) the

Memory Lock

selected image.

Presentation Move to Presentation screen.

N o t e

Movie Play Menu

Icon Name Function

The icons disappear after about ten seconds from showing

the display. If you want to operate the icons, you will tap

any place on the screen. The icons show again.

Play

Pause

Cueing

Repeat On

Play/stop/cue the movie.

Play the movie on loop.

Repeat Off

Set the output audio volume.

Down

Thumbnail Return to thumbnail display.

Presentation screen (Picture display)

N o t e

Icon Name Function

Highlight Highlight and draw attention to a particular section of the image.

Mask Mask a section of the image.

Scroll Expand to a set size and allow scrolling of the enlarged section.

Compare Picture Display a still image and live image together.

Mosaic Apply a mosaic effect to the image.

Image Rotation Rotate the image by 0°、90°、180°、270°.

Exit Return to Picture display.

• You may not be able to display image data not saved by this product or converted using the

conversion function of the software supplies.

• File Converter cannot convert movies.

• You cannot display pictures other than DCF system compliant ﬁ les and ﬁle structures.

• Movie files that have the file name other than “MVI_****.MP4” cannot be displayed.

• Only picture files and movie files that are saved under the folder ¥DCIM¥100_ELMO on the

SD card/USB memory will be available for playback.

• Many, but not all Images taken by other digital cameras can be displayed (viewed) on this

product (examples of images that cannot be displayed: images larger than 4092 X 4092 pixels

in size, 4:1:1 image file formats, etc.).

• Use the File Converter of the supplied Image Mate software to convert the image files taken

with a digital camera to the files viewable with the unit.

N o t e

3-2 Outputting a different image to RGB

OUT and HDMI OUT

This unit can output a different image to RGB_OUT and HDMI_OUT.

While outputting a camera image to HDMI output terminal, this unit can output the image of one of

either HDMI IN1, HDMI IN2, RGB IN1, or RGB IN2 to RGB output terminal.

①Tap the [ (Signal select)] > [ ] on the touch panel，and tap [ ] .

②Tap the [ (Signal select)] > [ ] on the touch panel.

③ Tap one of [HDMI1], [HDMI2], [RGB1] or[RGB2] that belongs to the output terminal that you

want to output.

The selected input image is output to RGB output terminal in resolution of selected input

image.

The camera image is output to HDMI output terminal.

• When selecting external input image, do not change the resolution of the input image.

N o t e

3-3 Saving data stored on an SD card to

PC via USB cable

CAUTION

• Tap [ (Settings)] > [ ] on the touch panel to set to [Mass Storage].

• Insert the SD card with the label facing up. Forcing it into the slot with the wrong side

up may cause a malfunction.

By connecting this equipment to a PC via USB, you can save the image data stored on the SD

card to the PC.

The operating system (OS) for the connected PC should be Microsoft Windows XP (SP2 or later),

Windows Vista, Windows 7 or Windows 8.

① Turn on the equipment and the PC.

② Connect the equipment to the PC with the supplied USB cable.

• When you connect the equipment to the PC for the ﬁrst time, the required drivers are

installed automatically using the plug-and-play function of Windows. From the second time

and thereafter, the drivers are not installed again.

N o t e

My Computer

Removable Disk

③ The equipment is recognized as a removable disk. You can view the image data on the SD

card with the viewer software of the PC.

• The image data is stored as JPEG ﬁles or MP4 files in the following folders:

CAUTION

• You can not save, delete, lock, unlock, or format the images from the PC.

• The image ﬁles are saved with the correct date and time from [Clock setting] .

• Do not connect/disconnect the USB cable while operating the product using the touch

panel or remote control. This may cause a malfunction.

• While the product is in the USB-connection mode, do not switch [USB Mode ] to another

mode by tapping [ (Settings)] > [ ] on the touch panel.

• We recommend using a USB 2.0-compliant USB cable.

• Depending on the USB environment used by the PC or any peripheral devices, image

transfer may be disrupted.

• Operation is not guaranteed for all environments.

• If [USB Mode] has been set to [Mass Storage] and the equipment is connected to the PC,

you can not save, delete, lock or unlock the pictures and movies in the SD card or format

the SD card using the equipment. (You can do above operations to the ﬁ les in the USB

ﬂash drive).

• Make sure to disconnect the USB cable before switching [USB Mode] from the touch

panel.

N o t e

3-4 Presentation using a USB-connected

PC with the supplied software

• Tap [ (Settings)] > [ ] on the touch panel to set to [Application].

“Image Mate” is available from the supplied CD-ROM.

By using the “Image Mate” software for controlling this equipment included in the CD-ROM, you

can perform the following tasks:

・Transfer movie/picture data to the PC

・Operate the product from the PC

For information on the requirements of the connected PC, OS types and the software guides, see

the “Image Mate” installation manual and the “HELP folder” on the CD-ROM.

N o t e

CAUTION

• Do not connect/disconnect the USB cable while operating the equipment using the touch

panel or remote control. This may cause a malfunction.

• We recommend using a USB 2.0-compliant USB cable.

• Depending on the USB environment used by the PC or any peripheral device, image

transfer may be disrupted.

• Operation is not guaranteed for all environments.

• Make sure to disconnect the USB cable before switching [USB Mode] from the touch panel.

3-5 Displaying the Video Image through

Network Connection

When connection is made to http://192.168.0.100 on the browser, the device’s top page opens.

When [50%], [75%] or [100%] of [Live] is clicked, the video image is displayed. When

[CAPTURE] is clicked, the still image is displayed.

Top page

Name Function

LIVE

①

To display the video image at 50%, 75% or 100% scale.

(Video image display)

CAPTURE To display the still image.

②

SETUP

③

To display the configurations page.

(Ethernet setting)

Live

Name Function

CONTROL

①

(WEB remote control)

CAUTION

• The Live and Capture can not be displayed during the recording.

• The Live and Capture can not be displayed during the playing movie.

• The Live and Capture can not be displayed while the Compare Picture function is in

operation.

To display the WEB remote control when this item is clicked.

WEB remote control

①

②

ZOOM

Name Function (One-click operation)

TELE To zoom in.

WIDE

To zoom out.

LAMP

③

④

BRIGHTNESS

⑤

⑥

⑦

FOCUS

⑧

⑨

Toggle between base illumination and → material illumination → both

NORMAL

OPEN

NEAR

FAR

CONFIGURATIONS

illuminations go out in this order.

Return the automatic brightness adjustment level to the standard level.

Brighten the camera image.

Darken the camera image.

Move the focus near.

Move the focus far.

Focus the camera automatically.

①

②

③

Network Configuration

①

- Configuration of the current network.

②

TOP Display the top Home page.

③

Name Function

Display the network configuration page.

User name and password need to be entered.

(Factory default setting: User name <root> , Password <root>)

Password for the Network configuration. Up to 15

Network Configuration

① ②

③ ④

⑤

⑨

⑦

⑥

⑧

Name Function (< >: Factory settings)

IP address information set in this camera system.

① IP address

<192.168.0.100>

② Subnet mask <255.255.255.0>

Router IP address.

③ Default gateway

<0.0.0.0>

Port number for displaying the Live image.

④ Port number

This port number is entered from TCP:49152 to TCP:65535.

<TCP:50000>

⑤ Root password

alphanumeric characters can be entered. <root>

To set or change the password, this check box should be

checked. If this check box is checked but nothing is entered in

⑥ □Change

the password edit box, the relevant password information will

be cleared.

⑦ Setup Set to the contents displayed.

⑧ Clear Reset/clear all edited contents.

⑨ Configurations Display the configurations page.

N o t e

• To enable the access to this camera system on the web browser, the PC environment should

be as follows:

- Windows XP (SP2 or later) / Vista / 7 / 8 has been installed.

- JRE (Java Runtime Environment) 1.6.0_29 or later has been installed, and Java (Sun) is

valid.

- Internet Explorer6 or later has been installed.

• This camera system does not guarantee normal access operation on all web browsers.

• Depending on the version of the OS, the window size may not be set properly and the scroll

bar may be displayed.

• Depending on the settings of the Windows or virus check software, loss of connection to the

camera and distorted video image, could occur. In this situation, adjust the settings properly

following the Windows instruction manual or the virus check software.

• This product uses port HTTP:80 and TCP:50000 (Default setting) for LIVE (Video image

display).When this product is connected to a router, firewall, etc., set the port accordingly.

• Live and Capture can not be displayed during SD mode.

Live and Capture can not be displayed during recording.

Live and Capture can not be displayed during play back movie.

Live and Capture can not be displayed while the Compare Picture function is in operation.

• This product can be remote-controlled or the status of this product can be obtained by using

the remote control(CGI). For further information such as the commands, contact the dealer

from whom you have purchased this product or our branch/office near your location.

•

Default setting of the browser address is “http://192.168.0.100”. Set the IP address to be

used with the [SET UP] in the Network configuration.

• When the resolution settings are changed, restart the browser.

• Changes made to the network settings of IP address, subnet mask, default gateway, port

number or password, become effective after the product is restarted.

N o t e

3-6 Using [MIC IN] and [AUDIO IN]

The microphone input and the audio input are mixed and output from [AUDIO OUT]. The

microphone input level alone can be adjusted on the touch panel.

Only the microphone for PCs (electret condenser microphone) can be connected to [MIC IN].

If a microphone other than that for PCs is connected to [MIC IN], this camera system could

malfunction.

Before connection, carefully check the specifications of the microphone.

N o t e

3-7 Using the ELMO Wireless Slate/Tablet

(CRA-1) with the equipment

By using the separately sold wireless pen tablet with this equipment, you can add comments or

draw on camera images directly.

You can also directly perform such operations as zooming in/out.

ELMO Wireless Slate / Tablet

CRA-1

CODE：１３０７

■Connecting the ELMO Wireless Slate/Tablet

(CRA-1)

① Set up the equipment as shown in the ﬁgure above and connect to the projector. Then turn on

the equipment.

② Connect the dedicated wireless adapter supplied with the pen tablet to the equipment.

③ Turn on the pen tablet.

The OSD menu may not be displayed when you connect a tablet while the input is changed. In

this case, connect a tablet again after establishing input and select again.

menu button

■Basic operations

1. Draw

Touch the tablet and move

2. Move the cursor

Lift from the tablet and move

● Drawing lines

Touch the tip of the pen to the surface of the tablet and move the pen.

3. Select a menu button

Touch the

If [ ] or [ ] has been selected, the pen will draw a line. Use this function to

draw/erase lines.

Keep pressed down

● Moving the cursor

Move the pen slightly above the surface of the tablet.

The cursor on the screen moves as the pen moves. Use this function to move the cursor.

Lift the pen a little

N o t e

● Selecting a menu button

Move the pen slightly above the surface of the tablet to move the cursor and then touch the pen

within the working area on the tablet.

Use this function to select a menu button.

CAUTION

Press the tablet lightly with the pen; do not press hard.

• Hold the pen as upright as possible; holding the pen at an angle may result in a failure of the

tablet to recognize the pen.

• If the pen is not used for a while, the power saving mode is activated. Touch the tip to

reactivate the pen before you use it again.

Touch once

The working area on the tablet corresponds to the whole screen.

Icon

Name

Function

N o t e

■Selecting how to use the pen tablet from the

tablet menu

To use the pen tablet, touch a function key at the top of the tablet and select a mode according to

the situation described in the table below:

Write to/work with

camera images

(Camera Mode)

Write on a white screen

(Whiteboard Mode)

Work with/write to

stored data

(Play Mode)

You can not operate device by the touch panel while using the tablet.

Setting

Display an image on the document camera as a background, and

draw on it with the pen tablet.

Display a white image as a background, and draw on it using the

pen tablet.

Display images stored on the SD card.

You can draw on the displayed image only when it is a still picture.

You can not draw on a movie with the pen tablet.

Specify settings for the pen tablet (the settings are common to all

modes).

Change OSD menu show/hide

■Writing to camera images

You can draw on camera images.

Menu descriptions

Pressing [ ] or [ ] switches the menu pages.

Support Function menu

Switch page

Main menu

Switch page

You can change the settings for the pen in the Setting menu.

comments/drawings; the cursor and menu icons are not captured.

Main Menu 1

Icon Name Function

Select Pen1.

Pen1

Pen2

Clear Screen

Capture

Rec

The initial color setting is Red.

Select Pen2. The initial color setting is Black. You can change the settings for the pen in the Setting menu.

Erase everything drawn on the screen. If you need to erase a part of a drawing, move the cursor to the section to be erased, and touch the section with the pen while pressing the pen Erase button.

Capture the image currently displayed on the screen as a picture and save it on the SD card. This feature captures only the displayed camera image and your

Record the image currently displayed on the screen as a movie and save it on the SD card. This does not record the lines drawn with the tablet, the menu icons, or the cursor.

Setting

Access the settings for Pen and Eraser.

Go to Main Menu 2.

Main Menu 2

Icon Name Function

Zoom In Enlarge the size of the camera image.

Zoom Out Reduce the size of the camera image.

AF Enable autofocus operation.

Brighten Brighten the camera image.

Darken Darken the camera image.

Next Go to Main Menu 1.

Setting Menu

Icon Name Selection Item Default Function

Red レ Set the pen color to red.

Pen1 Color

Pen1 Thickness

Pen2 Color

Blue Set the pen color to blue.

Black Set the pen color to black.

Thin Decrease the pen thickness.

Medium レ Set the pen thickness to medium width.

Thick Increase the pen thickness.

Red Set the pen color to red.

Blue Set the pen color to blue.

Black レ Set the pen color to black.

Thin Decrease the pen thickness.

Pen2 Thickness

Erase Area

Exit

Medium レ Set the pen thickness to medium width.

Thick Increase the pen thickness.

Narrow Select small erase area.

Medium レ Select medium erase area.

Wide Select wide erase area.

Return to the previous level of menu.

Support Function Menu

Icon Name Function

Show

Hide

Menu Change Support Function Menu.

Next Picture Move to the next picture page.

Prev Picture Move to the prev picture page.

Show/hide the Support Function Menu.

Scroll

Mask

Highlight

Image Rotation

Mosaic

Compare Picture

Enlarge the image to the size you specify, allowing you to move within the enlarged area.

Mask part of the image.

Highlight part of the image you want to emphasize.

Rotate a Camera image by 180° in Camera mode. Rotate a still image saved in the SD card by 90° in Playback mode.

Apply the mosaic effect to the image.

When this function is selected while the camera image is displayed, the camera image will be displayed at the left side of the screen and the RGB1-In image will be displayed at the right side of the screen.

When this function is selected while a still image is displayed, the camera image will be displayed at the left side of the screen and the still image will be displayed at the right side of the screen.

When this function is selected while the external input image is displayed, the camera image will be displayed at the left side of the screen and the external input image will be displayed at the right side of the screen.

Posi/Nega

Color/B&W

* : Camera mode only.

Output positive camera images.*

Output negative camera images.*

Output color camera images.*

Output black and white camera images.*

button.

comments/drawings; the cursor and menu icons are not captured.

■Using as a whiteboard

You can draw on any blank white images or areas used as a background.

Menu descriptions

Main Menu

Icon Name Function

Select Pen 1.

Pen 1

Pen 2

Clear Screen

Capture

The initial color setting is Red. You can change the settings for the pen in the Setting menu.

Select Pen 2. The initial color setting is Black. You can change the settings for the pen in the Setting menu.

Erase everything drawn on the screen. If you need to erase a part of a drawing, move the cursor to the section to be erased, and touch the section with the pen while pressing the pen Erase

Capture the image currently displayed on the screen as a picture and save it to the SD card. This feature captures only the displayed camera image and your

Setting

Specify the settings for Pen and Eraser.

Setting Menu

Icon Name Selection Item Default Function

Red レ Set the pen color to red.

Pen1 Color

Pen1 Thickness

Pen2 Color

Blue Set the pen color to blue.

Black Set the pen color to black.

Thin Decrease the pen thickness.

Medium レ Set the pen thickness to medium width.

Thick Increase the pen thickness.

Red Set the pen color to red.

Blue Set the pen color to blue.

Black レ Set the pen color to black.

Thin Decrease the pen thickness.

Pen2 Thickness

Erase Area

Exit

Medium レ Set the pen thickness to medium width.

Thick Increase the pen thickness.

Narrow Select small erase area.

Medium レ Select medium erase area.

Wide Select wide erase area.

Return to the previous level of menu.

■Using the SD card

You can display a picture or movie stored on the SD card and use the tablet to draw or write on it.

• Thumbnail display

Picture

When you select an image from the thumbnails, the selected image is displayed on the screen.

Picture

Menu descriptions

Thumbnail display

Icon Name Selection Item Function

Prev Page Move to the previous thumbnail page.

Next Page Move to the next thumbnail page.

Next Menu Move to the next menu page.

USB Flash

Drive

Picture

Movie

Memory Lock

Switch the data displayed as thumbnails

between movies and pictures.

Lock (set as protected) or unlock (set as

Lock/Unlock

unprotected) the selected image.

Lock All Lock (set as protected) all thumbnail images.

Unlock All Unlock (set as unprotected) all thumbnail images.

Delete

Exit Exit the current menu.

Yes Delete the selected image.

No Cancel deletion.

Format

Exit Exit the current menu.

Yes Format the SD card.

No Cancel formatting.

Exit Exit the current menu.

100

Elmo P100HD, 1340 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

IMPORTANT SAFEGUARDS

BEFORE YOU USE

CONTENTS

1 1 BUNDLED ITEMS

2 2 BASIC OPERATIONS

2-1 Document Camera

■Part Names

■Touch panel

■Rear panel and cable connection

■Side panel

■Moving Parts of the Document Camera

2-2 Supplied Accessories

■Remote Control

■Remote Control Strap

■Image Mate CD-ROM

■Preparation

2-3 Shooting Images

■Setting up the main unit

■Turning the power ON/OFF

■Operating the touch panel

■Adjusting the size

■AF（Auto focus）

■Adjusting the brightness

■Turning the illumination ON/OFF

■Image selection

■Details of Each Function

■Icon descriptions

3 ADVANCED OPERATIONS

3-1 Using an SD card/USB ﬂash drive

■Saving images

■Displaying the stored data

3-6 Using [MIC IN] and [AUDIO IN]

■Basic operations

■Writing to camera images

■Using as a whiteboard

■Using the SD card