Elmira Stove Works 1956BB, 1955CRE, 1956BYLP, 1954CW, 1954PCA INSTALLATION INSTRUCTIONS AND OPERATION MANUAL
...
Installation and Operating Instructions for
NORTHSTAR
Electric Ranges (Model 1954)
Dual Fuel Ranges (Model 1947 & 1955)
Gas Ranges (Model 1956)
ATTENTION:
Do not line the oven
bottom with any type of
liners, foil or cookware.
Do not cook on the oven
bottom. Permanent
damage to the oven
bottom will result!
NOTE: COOLING FAN
When the oven is heated,
a fan turns on to moderate the
temperature of the switches. The
fan will automatically shut off
when the oven cools.
This is a normal part of the
stove’s operation.
Thank you for purchasing a Northstar Retro Range.
You have purchased a quality, world-class product.
Years of engineering experience have gone into its manufacturing.
To ensure that you will enjoy many years of trouble-free
operation, we have developed this User Guide.
It is full of valuable information on how to operate and maintain
your range properly and safely. Please read it carefully.
BY
#1704 -16
GAS RANGE WARNING
WARNING: If the information in this
manual is not followed exactly, a fire or
explosion may result causing property
damage, personal injury or death.
– Do not store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any other
appliance.
– WHAT TO DO IF YOU SMELL GAS.
• Do not try to light any appliance.
• Do not touch any electrical switch; do not use any
phone in your building.
• Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.
• If you cannot reach your gas supplier, call the fire
department.
– Installation and service must be performed by a
qualified installer, service agency or the gas supplier.
BEFORE USING YOUR RANGE READ THIS BOOK CAREFULLY
If you received a damaged range:
Immediately contact the dealer that sold you the range.
Before you request service:
Check Troubleshooting. It lists causes of minor operating problems that you may be able to correct yourself.
TABLE OF CONTENTS
Safety InStructIonS – All Models ........................... 3
Amperage Requirements & BTU’s ............................ 4
Storage drawer/
optIonal warmer drawer ............................. 17
Safety InStructIonS – Gas ...................................... 4
InStallIng your range .......................................... 5
Installing Range in to Cabinets .................................... 6
Electrical & Gas Connection Locations ...................... 7
electrIc cooktop .................................................... 7
SelectIon & uSe of potS & panS ....................... 8
grIddle optIon ........................................................ 10
cannIng ....................................................................... 10
gaS cooktop............................................................. 10
Manual Burner Adjustment ....................................... 10
Gas Burner Cleaning ................................................. 11
oven ventIng (Gas Top Models) .............................. 11
gaS Supply SyStem ................................................. 12
range top converSIon to “lp” ....................... 12
oven converSIon model 1956 ........................... 14
oven controlS & clock ..................................... 15
Setting Clock ............................................................. 15
Oven Light ................................................................. 15
Clock vs. Digital Display........................................... 15
Self Clean .................................................................. 15
Maintenance and Minor Repair ................................. 16
Replacing Oven Lights .............................................. 17
convectIon & Standard cookIng tIpS .......... 18
Standard Oven Meat Roasting Chart ......................... 21
Standard Oven Baking Chart ..................................... 22
Introduction to Convection Cooking ......................... 23
Convection Meat Roasting Chart .............................. 23
Convection Poultry Roasting Chart ........................... 25
Convection Yeast Bread Baking Chart ...................... 25
Convection Quick Breads Baking Chart ................... 26
Convection Dessert Baking Chart ............................. 26
wIrIng dIagram modelS 1954, 1955, 1956 ... 27
wIrIng dIagram modelS 1947 ........................... 28
cleanIng guIde ........................................................ 29
ServIcIng range under cooktop ..................... 29
range troubleShootIng ...................................... 30
ServIce & warranty ............................................ 32
2
SAFETY INSTRUCTIONS
(All Models)
IMPORTANT! Save these instructions for the local
inspector’s use.
WARNING! Prior to installing this appliance, read the
Safety Instructions as they relate to Installation on pages
4 through 6 of this manual. Failure to follow these instructions could result in serious electric hazard, risk of fire,
and/or personal injury.
Models 1947, 1954 and 1955 are equipped with a 240
volt, standard range power cord & plug. See page 4 for
amp ratings of each model.
Models 1956 comes with a 120 volt, 10 amp power cord
& plug.
Use this appliance for its intended use, as described in this
manual.
Never use your appliance for warming or heating the
room.
Do not assume that you know how to operate all parts of
the range. Some features may work differently from those
of your previous range.
Do not climb, stand or hang on the door or range top.
This can damage the range or tip it over, causing severe
personal injury.
Children
Do not leave children alone in the area where your range
is in use. They should never be allowed to stand or sit on
any part of this appliance.
Instruct your small children that the range is not a toy and
could hurt them. As your children grow up, teach them the
proper and safe use of the range.
Children must be taught not to use the oven door as a
stepping stool to reach the cabinet above, as it may result
in an injury.
Caution
Do not store items of interest to children on console
above the range or on the back of the cooking surface.
Children climbing to reach items could be seriously
injured.
When cleaning cycle is on, the oven door and cooking
surface will be hot. Keep children away from the range as
a safety precaution.
Storage
Do not store gasoline, flammable vapors or materials,
etc., in the oven, storage drawer, warmer or around the
appliance area.
Hot Surface
Exercise caution. Surfaces may be hot enough to burn.
Electric elements may be hot even when they appear dark
in color.
Do not operate surface burners without utensils in place.
Allow elements and burner surfaces to cool before
cleaning. If a wet sponge or cloth is used to wipe spills on
a hot cooking area, be careful to avoid steam burn. Some
cleaners can produce noxious fumes if applied to a hot
surface.
Loose clothing of flammable material (pot holders) could
ignite if brought in contact with hot burners and may
cause severe burns.
Moist or damp pot holders on hot surfaces may result in
burns from steam. Do not let pot holders touch hot heating
elements. Do not use towels or other bulky cloths as pot
holders.
Cooktop temperatures increase with the number of
elements on. With three or four elements turned on,
surface temperatures are high. Exercise care when
touching the cooktop.
Fire (Optional Exhaust Hood)
Keep the hood and grease filters clean to maintain good
venting and to avoid grease fires.
Do not let cooking grease or other flammable materials
accumulate in or near the range.
Grease
Grease is flammable and should be handled carefully.
Avoid letting grease deposits collect around the range in
vent fans. Don’t leave cans of drippings sit around the
range; refrigerate or dispose of promptly. Let quantities
of hot fat (a pan of deep fat for example) cool before
attempting to move or handle it. Grease fires can often
be extinguished by quickly putting on the pan lid or by
covering with baking soda. Do not attempt to extinguish
with water because this will spread the fire.
Never pick up a flaming pan.
Oven
Stand away from range when opening the oven door. Hot
air or steam which escapes can cause burns.
Do not heat unopened food containers in the oven. Pressure
could build up and the container could burst, causing
injury or damage to the range.
Keep oven vent ducts unobstructed.
Keep oven free from grease build up.
Place oven rack in desired position while oven is cool.
If rack must be handled when hot, do not let pot holder
touch heating elements in the oven.
Pull out oven rack to the rack stop to reduce chance of
burns from touching hot surfaces of the door and oven.
When using cooking or roasting bags in oven, follow the
manufacturer’s directions.
Do not use your oven to dry newspapers.
Aluminum Foil
Do not use aluminum foil to cover oven racks. This will
restrict heat circulation. Do not place aluminum foil in
bottom of oven as a spill protector. Permanent damage to
oven will result.
3
Plastics
All plastics are vulnerable to heat, although some will
withstand higher temperatures than others. Keep all
plastics away from parts of the range which may become
slightly more than warm when the range is in operation.
Self-Cleaning Oven
The door gasket is essential for a good seal. Care should
be taken not to rub, damage or move the gasket.
Do not use oven cleaners on self-cleaning ovens prior
to clean ing. Damage may occur to oven finish at high
temperatures. Remove aluminum or plastic utensils, food
or combustible materials from oven and cooktop before
self-cleaning. (See Self-Cleaning – Page 15)
NOTE: Oven cleaner will not harm porcelain oven but
should not be used in conjuction with selfcleaning.
Surface Cooking
Use proper pan size. Select pans large enough to cover the
element. The use of undersized pans will expose a portion
of the element which may result in burns, ignition of
clothing or spillovers directly on element.
Never leave surface units unattended at high heat setting.
Boil over or boil dry conditions could result in a fire.
Do not use glass or glazed ceramic cookware on the
surface burners, as sudden change in temperature may
break them.
Always turn off surface unit, before removing pots or
pans.
Turn handle of the pan toward the center of the cooktop,
without extending over nearby elements. This will reduce
the possibility of accidentally overturning the pan.
Let hot pans cool in a safe place, out of the reach of young
children. Never set hot pots on a combustible surface.
Do not use decorative metal covers on electric surface
elements. A covered element, when turned on, could
result in a burn or damage to the element.
Frying
Use as little oil as possible. Filling the pan too full of oil
can cause spillovers when food is added.
Foods for frying should be as dry as possible. Frost on
frozen foods or moisture on fresh foods can cause hot oil
to bubble up. Spillovers, fire and burns from splatters could
occur.
Use a deep fat thermometer whenever possible to prevent
overheating oil beyond smoking point.
Deep Fryer
Use extreme caution when moving a hot grease kettle or
disposing of hot grease.
Ventilating Hoods
Clean ventilation hood frequently — grease should not be
allowed to accumulate on hood or filter. When flaming
foods under the hood, turn the fan off. The fan, when
operating, may spread flame.
Service
Do not repair or service any part of the range unless
specifically recommended in this manual. All other
servicing should be referred to a qualified technician.
Disconnect the range from wall receptacle, fuse, or breaker
before performing service.
Safety
Your range, like many other household items, is heavy
and can settle into soft floor coverings such as cushion
vinyl or carpeting. When moving the range on this type of
flooring use care.
If your range must stand beside a refrigerator, allow at
least 2” between the two appliances for air circulation.
The heat from the range may affect refrigerator
performance.
Make sure that all the packing materials have been removed
and that all controls are in the off position before plugging
in the power cord.
Electrical Connection
Amperage requirements BTU’s NAT BTU’s LP
Model 1947- 40 Amps, 240 Volts 66,000 59,400
1954- 40 Amps, 240 Volts — —
1955- 25 Amps, 240 Volts 43,000 38,700
1956- 10 Amps, 110 Volts 59,000 53,100
All ranges come with standard 4 wire range cord attached.
This cord must be plugged into a standard range receptacle
provided by your electrician.
SAFETY INSTRUCTIONS – GAS
Important Instructions
Do not use range as a heater. Never use the range as a
kitchen heater. Prolonged use of the range without adequate
ventilation can be hazardous. Oven controls and top burners
are not designed for home heating and component failures
that may result from such abuse are definitely not covered by
the warranty.
WARNING: This product must be installed by a licensed
plumber or gas fitter, when installed within the Commonwealth of Massachusetts.
#1 This installation must conform with local codes and
ordinances. In the absense of local codes, installations must
conform with American National Standard, National Fuel
Gas Code ANSI Z223.1–latest edition (**) or CAN/CGAB149–latest edition (***) installation codes.
#2 Input ratings shown on the serial/rating plate are for
elevations up to 2,000 feet (609.6 m). For elevations above
2,000 feet (609.6 m), ratings are reduced at a rate of 4% for
each 1,000 feet (304.8 cm) above sea level.
4
Mobile Home Installation
The installation of this range must conform to the
Manufactured Home Construction and Safety Standards,
Title 24 CFR. Part 3280 (formerly the Federal Standard
for Mobile Home Construction and Safety, Title 24, HUD,
Part 280); or when such standard is not applicable, the
Standard for Manufactured Homes Installations 1982
(Manufactured Home Sites, Communities and Setups),
ANSI A225.1q/NFPA 501A* or with local codes.
The installation of this range must conform with the
current standards CAN/CSA-Z240–latest edition*** or
with local codes. When this range is installed in a mobile
home, it must be secured to the floor during transit. Any
method of securing the range is adequate as long as it
conforms to the standards listed above.
Note: The metal chassis of the range MUST be earthgrounded in order for the control panel and burner spark
ignition to work. Check with a qualified electrician if you
are in doubt as to whether the metal chassis of range is
earth-grounded.
Copies of the standards listed may be obtained from:
* National Fire Protection Association
Batterymarch Park
Quincy, Massachusetts 02269
** American Gas Association
1515 Wilson Boulevard
Arlington, Virginia 22209
*** Canadian Standard Association
178 Rexdale Boulevard
Rexdale (Toronto), Ontario M9W 1R3
Floor Covering
Never install a range over inferior kitchen carpeting, vinyl
tile or linoleum. These should be able to withstand at least
175°F without shrinking, warping or discoloring.
Curtains
If your range is near a window, use an appropriate
window treatment. Do not use long curtains which could
blow over the top burners and create a fire hazard.
If You Smell Gas
If this is a new range installation, your installer has not
done a proper job of checking for leaks. Connections can
loosen in transportation. If the range connections are not
perfectly tight, you can have a small leak and therefore a
faint gas smell.
FINDING A GAS LEAK IS USUALLY NOT A
“DO IT YOURSELF” PROCEDURE.
Some leaks can only be found with the controls in the
“on” position exposing the user to serious burns. Never
use a match or flame to locate a leak. Turn off the gas to
the range and call a qualified serviceman.
Flame Size: Top burner flame size should be adjusted so
it does not extend beyond the edge of the cooking utensil.
Excessive flame is hazardous.
Use of High Flame: When using a high flame, never
leave any pans unattended on this heat setting for long
periods. Hot oil is particularly hazardous since it can
become hot enough to ignite.
Do not obstruct the flow of combustion and ventilation air
to the range.
Any openings in the wall, behind the range or the floor
under the range must be sealed.
Venting
Never block the vents (air openings of the range). They
provide the air inlet and outlet which is necessary for the
range to operate properly with correct combustion. The
oven vent is located at the rear of the main top.
Type of Gas
Natural and LP Gas (propane). Ranges are factory
assembled for natural gas unless otherwise specified and
cannot be used with LP Gas without some adjustments.
Be sure your range is correctly adjusted by a qualified
serviceman or installer for the type of gas on which it is to
be used. (See Conversion, page 12 -15).
NOTE: In this manual, propane is referred to as LP
(liquid petroleum).
Gas hook up locations - Models 1947 and 1955: The
1/2” steel gas elbow exits the stove on the right side, 33”
off the floor. Model 1956: the connection is located in
the center, 2” off the floor.
INSTALLING YOUR RANGE
Be sure your appliance is properly installed and grounded
by a qualified technician in accordance with the installation
instructions and local building codes.
Power cord installation
The new U.S. revised electrical code states that all new
construction must use a FOUR WIRE range power cord.
Existing construction may use a three wire range power
cord. NOTE: The difference is, a four wire cord has a
separate ground. A three wire cord is grounded through
the neutral.
Installation, adjustment and service of this range must
be performed only by a qualified gas range installer or
electrical serviceman. This is necessary to insure proper
operation of the range and to avoid the possibility of
damage to the range or injury to the users.
WARNING: Be careful when reaching into storage cabinets
above range while it is in operation. One might accidentally
contact a hot burner when using a hand for support or have
one’s clothing come in contact with top burner flame.
5
Location
If possible, the range should be located to avoid the main
“traffic path” through the kitchen or where an open door
might block a passageway or create an awkward working
situation. If possible, it should be so located where cabinet
working space is available on either side. Drafty locations
should be avoided to prevent gas burner outage and poor
air circulation.
Temperatures
To cook, you must have heat. Some parts of the range are
therefore going to get warm or even hot. Consider this in
choosing a range location. Do not leave children alone or
unattended near the range when it is in use. Let burner
grids and other surfaces cool before touching them or
leaving them where children can reach them.
Clearances
This range may be installed with adjacent surfaces
touching the base cabinets and the back flush with the
back wall. Models 1947, 1955 and 1956 gas ranges require
a CGA/AGA approved stainless steel gas flex line or a
flexible copper coil 1/2” in diameter and at least three feet
long so the range can be moved for service.
To eliminate the risk of burns or fire by reaching over
heated surface burners, cabinet storage above the range
should be avoided. If overhead storage is unavoidable,
clearances between the cooking surface and unprotected
wood or metal overhead cabinets must be no less than
32”. The clearances on electric models between the
cooktop and unprotected overhead cupboards is 30”. This
distance may be reduced to 24” when the bottom wood
or metal cabinets are protected by not less than 1/4” thick
flame retarding millboard covered with not less than No.
28MSG sheet steel, 0.015” thick stainless steel, 0.024”
thick aluminum or 0.020” thick copper.
NOTE: Clearances specified to combustible construction
(walls and materials) are based on a temperature rise
of wood resulting from appliance operation. These
clearances are suitable for walls of studding, lath and
plaster or other types of combustible material which have
a density of 20 lbs. per cu. ft. or more. No evaluation of
clearances has been made for low density cellulose, fibre
board and similar materials which have a density of less
than 20 lbs. per cu. ft., nor to plastic tiles or sheeting.
Minimum Clearances to Combustibles
A B C D E F
All Electric Model 1954 0” 0” 30” 0” 0” 13” max.
Dual Fuel Models 1947 & 1955 3”
All Gas Model 1956 3”
min.
ht. 18”
min.
ht. 18”
3”
3”
min.
32” 0” 0” 13” max.
ht. 18”
min.
32” 0” 0” 13” max.
ht. 18”
1 = End of section of overhead cabinet
2 = Overhead center cabinet
3 = End wall or divider
Hood should be installed 28” to 30” from the bottom of
hood to the range cook top.
See Full Installation information
in Exhaust Hood Manual.
It is the responsibility of the installer to comply with the
installation clearances specified in this manual.
Cabinet Openings
Models 1954, 1955 and 1956 will fit into a 30 1/4” cabinet
opening.
Model 1947 will fit into a 36 1/4” cabinet opening.
Leveling Your Range
Place rack in oven. Place level on rack, first side to side,
then front to back.
The maximum depth of upper cabinets installed above the
range is 13”.
See the Minimum Clearances Chart for electric and gas
models below.
If the range is not level, adjust leveling legs up or down with
pliers or your fingers until range is level.
NOTE: Oven must be level for satisfactory baking performance.
6
Electrical and Gas Connection Locations
1947, 1955 Dual Fuel Ranges
ELECTRIC COOKTOP
Dual Fuel Range 1947, 1955
All Gas Range 1956
Gas line connection is
33" off of the floor and
3.5" in from the right
hand side of the range.
Electrical Cord is 12"
up from the floor.
1.5"
1954 All Electric and
have 220V 4 prong cord.
Plug depth is 1 1/2" and
cord length is 4 feet.
Surface Elements
Controls
Control knobs must be pushed
in before turning them to
a setting. They can be set
anywhere between MAX and
MIN.
The controls for the surface
elements provide infinite heat
settings. The numbers on the dial serve as a reference. The
control can be turned to any setting to provide the exact
heat required.
NOTE: The “Push to Turn Safety Control Knobs” on
the range are designed for child safety and to prevent
accidental operation.
Before using your glass cooktop for the first time: turn
the elements on MAX without a pan for 5 to 8 minutes
or until smoking stops. This smoking is normal and
non toxic.
High Speed Radiant - Electric Top Burners
Consists of a set of special RADIANT HEATER coils
embedded in thermal insulation. The element is designed
for fast heat response. You can see it light up almost
immediately.
Each element is fitted with a thermal limiter to ensure
the ceramic glass does not exceed the maximum SAFE
operating temperature. You may notice the element going
on and off a number of times during use. This is a normal
occurrence.
To maximize the efficiency of this type of element we
suggest you use it similarly to your previous burner. Turn to
maximum until the desired temperature is reached, then turn
it down to the setting that best maintains the desired heat.
Electrical Cord is 12"
up from the floor.
Regulator is centered and
approximately 2" in under
the range.
1"
1956 All Gas Model
110V Plug depth is
1" and does not recess
into the range.
Cord length is 3 feet.
• H or 9 – To start foods cooking and to bring foods
to a boil.
• 8-7 – To hold a rapid boil.
• 6-5 – To fry foods.
• 4 – To cook large amounts of vegetables
• 3-2 – To keep food cooking after starting it
on a lower setting.
• L – To keep foods warm until ready to serve.
Hot Lights
Hot lights are provided in the glass of all smooth top ranges.
Light glows when a burner becomes hot and shuts off when
the burner has cooled.
Controls
The radiant heating elements are controlled by a commonly
used Infinite Heat Switch that works on the principle of
percent on, percent off. For example, when the switch is
turned to the medium setting, the element will be on only
50% of the time. Because of the fast heat-up with these types
of elements, you will notice the units switching on and off.
7
Cookware
The best cooking results and the most economical use of
electricity will be achieved by using smooth, flat-bottom
pans. Pans should be at least the same size or slightly
larger than the cooking area. Ceramic cookware suitable
for stovetop cooking may be used. If pans smaller than the
size of the heating element are used, care should be taken
as the handles may get hot.
Built into each element, is a safety device which protects the
element from overheating. If using pans which are not ideal,
for example concave or convex bottom pans with shiny
bases, or those with ridged or grooved bottoms, the thermal
limiter can cause the element to switch off and on during
cooking, which means that food will take longer to cook.
Very thin, badly dented, and distorted pans with uneven
bottoms should not be used.
Pans with very shiny or reflective bottoms should not be
used.
Never place utensils with a skirt (e.g. a wok) on the
heated area.
Pans should not have rough bottoms. Do not slide pots on
the ceramic glass cooking surface, as this may mark or
scratch the cooktop.
If pans with aluminum bottoms are slid across the cooking
surface, metal marks could result. Such marks are easily
cleaned with any non-abrasive stainless steel cleaner,
provided they are removed immediately and not allowed
to bake onto the surface.
Any guidelines or recommendations given by the
saucepan or cooking utensil manufacturer should be
followed.
Do not use pans extending more than one inch beyond
element, except while canning. See figure 8.
Figure 8
Small diameter pans waste energy and spillage can flow
onto element. This increases chance of fire and burns.
Use non-stick coated cookware, for easier clean up.
Glass or pyroceram pans should be used only as the
manufacturer describes.
Pressure cookers, deep fat fryers, canners, etc. must be of
the correct size and have flat bottoms to work properly.
Energy Tips
Use cookware with tight-fitting lids, and flat bottoms
which completely cover the heated portion of the element.
Watch foods when bringing them to cooking temperatures
at high heat. When food reaches cooking temperature,
reduce heat to lowest setting that will keep it cooking.
Use residual heat with surface cooking. For example,
when cooking eggs in the shell, bring water to a boil,
then turn element off, and allow heat in water to complete
cooking.
When boiling water for tea or coffee, heat only the
amount needed. Do not use a wire trivet or any other kind
of heat retarding pad between the pan and the element.
SELECTION & USE OF POTS & PANS
Things Not To Do On A Ceramic Cooktop
Flat Bottoms
Thick, flat bottoms absorb and distribute the heat from
the element more evenly. Thin, uneven bottoms waste
energy and create hot spots that may burn the food onto
cookware.
Glass cooktops require heavy gauge flat bottom pans for
best cooking results.
Check flatness with a ruler or straight edge. See figure 7.
Figure 7
Pot Diameter
Select element to match pan diameter. The pot should
be slightly larger than the element to obtain best energy
usage, and avoid spillovers flowing directly onto element.
• Do not leave pots unattended or elements ON for
extended periods of time. If an element is mistakenly left
on for an extended period of time the built in thermal
limiter will ensure that the heat build-up is insufficient
to cause any adverse effects.
• Do not cook directly on the ceramic cooktop. The
surface of the cooktop can be damaged, and will be more
difficult to clean.
• Do not use wire trivets mats or aluminum foil. They
offer no cooking advantages and can damage the
ceramic glass surface. Never place plastic or any other
material which might melt on any part of the cooktop.
• Do not use the cooktop as a chopping board or cutting
surface. This type of use can scratch the surface.
• Do not leave heavy spills during cooking. Turn heat
off and allow surface to cool down. Remove the spills
with a clean, damp cloth (no detergent), taking care to
avoid burning fingers. If there is detergent in the cloth,
you may leave a layer of soil-laden film on the cooktop
surface, which can result in discolouration next time the
element is switched “on”. If a detergent film builds up,
use a ceramic glass cleaner-conditioner.
8
Care and Cleaning
To keep the exterior chrome trim in spotless condition,
wipe with a warm soapy cloth. Do not clean hot chrome
surface with a soapy cloth, use automotive chrome
cleaner on cool surface.
See page 28 for complete cleaning guide.
Caution - Product Damage Hazard
Before using any cleaners, ensure that it is suitable for
application on chrome trim.
Make sure that the glass ceramic surface has cooled down
before applying any cleaning materials.
1. Saving on Cleaning Time
• Make sure the bottom of pots and pans and cooking area
are clean and dry.
Select correct heat settings and use saucepans large
enough to accommodate food and liquid to eliminate
boilovers and splattering.
• Wipe up food spills and splatters from adjacent heating
areas before cooking.
• Do not drag or slide pots along the surface.
2. Daily Care
• Use a ceramic glass cleaner-conditioner, available
at supermarkets and major department stores. As the
cleaner-conditioner cleans, it leaves a protective coating
of silicone on the smooth surface, which helps prevent
scratches and abrasions in which food particles can
collect. It also helps prevent the build-up of mineral
deposits, and will make future cleaning easier.
• When cool, apply a dab of cleaner-conditioner in the
center of each heated area to be cleaned.
• For normal cleaning start with about 1 ml (1/8 tsp) of
cleaner-conditioner, and apply more if needed.
• Clean unit with a damp clean paper towel. To remove
more stubborn spots, use a slightly dampened nonimpregnated plastic or nylon pad specially made for
non-stick utensils.
• Wipe off this application with another clean, damp paper
towel, and wipe dry.
• Use liquid cleansers to remove any discoloration,
especially in hard water areas. A non-impregnated
plastic or nylon pad specially made for non-stick utensils
may also be used with these cleaners. Do not apply
excessive pressure while rubbing. This could cause
scratches over time.
• Apply cleaner-conditioner and polish with paper towel
or a soft dry cloth.
• Any smearing or hazing on the surface may be removed
with a lightly dampened paper towel, and polished with
a soft dry cloth.
• Do not use a sponge or a dishcloth. They may leave a
film of soil-laden detergent on the heating area which
may turn brown and resemble a discolouration the next
time the area is heated. If that should happen, cleanerconditioner will remove it.
Warning
Personal Injury Hazard
• NOTE: If a wet paper towel is used to remove spillovers
from warm cooking area, be careful to avoid steam
burns.
• Never mix different household cleaning products.
Chemical mixtures may interact, with objectionable or
even hazardous results.
Do Use
Ceramic glass cleaner-conditioner should be used
regularly to clean and protect glass-smooth top cooking
surface. If you run out, you may temporarily use baking
soda as a cleaning powder.
Do Not Use
1. Household detergents and bleaches.
2. Impregnated plastic or nylon pads.
3. Soap pads; these will scratch and mark.
4. Household abrasive powders except where specified;
these may scratch depending on the pressure applied in
use.
5. Chemical oven cleaners, e.g. aerosols and oven pads.
These are caustic cleaners, and may etch the surface.
6. Rust stain or bath and sink stain removers, as these will
mark and etch the surface.
7. Metal scrubbers.
How To Deal With Burned-On Spots (Model 1954)
1. Make sure area to be cleaned is warm to the touch.
2. The careful use of a stainless steel razor blade held at
approximately 30 degrees to the surface can be used to
remove stubborn burned-on spots from the surface.
3. Use cleaner-conditioner, and finally wipe the cooktop
clean with a paper towel or damp cloth.
If after the use of recommended materials there are some
persistent stains or marks on the cooktop, the unit should
be cleaned using a liquid cleanser. This will remove any
accumulated residue of cleaner-conditioner, and if applied
with a non-impregnated plastic or nylon pad for non-stick
pans, for at least three to four minutes, it will also take
off the film caused by salts and minerals before it has an
opportunity to discolor or develop into a problem. Finish
off with a touch of cleaner-conditioner, polish to a high
lustre.
Any smearing or streaking on the surface may be removed
with lightly dampened paper towel and polished with a
soft dry cloth.
Metal Marks
Certain metal pots, especially those with aluminum
bottoms may leave marks on the surface, especially if the
pan is allowed to slide. Use the cleaner-conditioner before
the unit is used again to prevent the mark from baking on
the surface.
9
Caution (Model 1954)
Product Damage Hazard
Ceramic glass cleaner-conditioner should be applied
regularly after use of other cleaners, otherwise over
a period of time the surface of the ceramic glass may
roughen, and cleaning will become progressively more
difficult. Staining may also occur.
Important Notes
1. In the event of the cooktop being scratched, soil will
collect and appear as fine lines. These are not fully
removable, but can be minimized by the daily use
of cleaner-conditioner. These scratches do not affect
cooking performance.
2. Soil from sugar solutions must be removed from the
cooktop before the syrup has set, otherwise it can
permanently bond to the ceramic surface.
GRIDDLE OPTION
OPTIONAL
GRIDDLE
Griddle
Set griddle over a back/front burner combination. Turn both
burners on MAX for a couple of minutes or until griddle
reaches frying temperature. Temperatures may be adjusted
as required.
control. The auto-reignition system senses when a burner
flame has gone out and will automatically reignite that
burner. There are no standing pilots to light or adjust.
See this page for cleaning and maintenance of top burners.
Operating Range During a Power Failure
To light a top burner during a power failure, hold a lit
match to the desired burner head. Turn the corresponding
control knob to any numbered position. After burner
lights, adjust flame to desired setting.
The gas oven requires electricity to operate.
Removal of Burner Knobs
Apply a piece of duct tape to the surface of the knob for
better grip. Pull off by hand or with a pair of pliers.
Manual Burner Adjustment On Low
The burners have been pre-adjusted at the factory for
best performance. You may manually adjust the low
settings up or down by removing the control knob while
the burner is lit and in the low position. While holding
the valve stem so it doesn’t turn, insert a small flat blade
screwdriver into the stem and turn the small brass screw
slightly in either direction until desired flame height
is obtained. Valve must be adjusted so low flame licks
around burner cap no less than 1/8”. See figure 11.
1/8"
CANNING
For best results, use a flat bottom, heavy gauge canner.
Canners with rippled bottoms will not work on electric
burners because the bottom does not make enough contact
with the element.
GAS COOKTOP
Gas cooktops are more forgiving than electric cooktops.
Most cookware will work, although tight fitting lids are
recommended for efficient cooking on both. Always
adjust the burner controls so that flames do not extend
past the edges of pots or pans.
Top Burners (Models 1947, 1955, 1956)
Your gas range is equipped with “state of the art” “Sealed
Gas Burners” and an “Auto-Reignition System”. The
sealed gas burners spread the heat evenly across the
bottom of the cooking utensil and provide infinite heat
Figure 11 Figure 12
NOTE: Low adjustment will not effect flame heights at
other settings. If a top burner flame has been adjusted too
low, the electronic ignitor may start to spark while burner
is on. Readjust flame until ignitor stops sparking.
Flame Appearance
The burners have been pre-adjusted at the factory to a
clean blue flame. On LP gas, a slight orange tip may be
visible. If flame is not as above, your gas serviceman
can check the regulator for proper setting with a water
manometer (U-gauge). The stove pressure should be
within + or - 10% of the pressure setting shown in this
manual.
10
Loading...