Elk products ELK-MC100 User Manual

* Try these other fine ELK products *

MM443 Magic Module, 4 Input, 4 Output, Programmable
MM447 Automation Controller w/Voice,Caddx Interface
MV480 Recordable Voice Module, 400 Channels
MKHOME1 Home Control Kit for Caddx NX Controls
MK400 Starter Kit, Includes MM443 & MK485
MK485 Programming Kit, MB485, Cables, Software
MK410 X-10® Transceiver Kit, Programmed MM443
MK420
MA100
MA101 iButton™ ‘Touchkeys’,10 pcs w/keyring holders
MA290 Proximity / Wiegand Data Interface to MM443
MB485 Data Bus Interface, RS232 to RS485
MC100 Clock / Calendar Module for MM443
ML8 Link Interface to Caddx NX Controls
MT100 Temperature Sensor Module for MM443
MM220 Magic Module, 2 Input, 2 Output, Programmable

1RT Speaker & Stainless Steel Enclosure
150RT Siren & Stainless Steel Enclosure
155RT Voice Siren in Stainless Steel Box

44 Speaker, 30 W,8 Ohm Compact Horn
45 Siren, Compact Horn, 118db
55 Voice Siren, Compact Horn
M120 Siren, Single Tone, 107db, Mini Horn
SP15 Speaker, 15 watt, Small Horn
SP30 Speaker, 30 watt, Horn
SP35 Speaker, 20 watt, Interior
SP40 Speaker, 40 watt, Horn
SS15 Siren, Dual Tone, 110db, Horn
SS30 Siren, Dual Tone, 120db, Horn
SS36 Siren, Dual Tone, 105db, Interior

73 ECHO Speaker, 20 Watt, Interior
74 ECHO Dual Tone Siren, Interior
75 ECHO Voice Siren, Interior
870 ECHO Speaker, Self Amplified

100 High Performance Siren Driver
110 Voice Siren Driver, English & Spanish
120 Recordable Voice Module and Siren
124 Recordable Voice Module, 4 Channels

950 Surge Suppressor, Phone & Power Line
951 Surge Suppressor, Phone - Single Line
955 Surge Suppressor, Phone - Dual Line

912 Compact Relay,12 Vdc, SPDT
912B Heavy Duty Compact Relay,12/24 Vdc, SPDT
924 Sensitive Relay, 12/24 Vdc, DPDT
941 Alarm Output Director
960 Delay Timer Relay, 1 sec. to 60 min.

1240 Battery, Lead Acid, 12v, 5Ah
1270 Battery, Lead Acid, 12v, 8Ah
12100 Battery, Lead Acid, 12v, 12Ah
12170 Battery, Lead Acid, 12v, 18Ah
12250 Battery, Lead Acid, 12v, 25Ah
P112 12 Volts DC, 1 Amp Power Supply w/Enclosure
P124 24 Volts DC, 800mA Power Supply w/Enclosure
P1216 12 Volts DC, 1.5 Amp Power Supply
P412 12 Volts DC, 4 Amp Power Supply
P624 Power Supply & Battery Charger
PD9 Power Distribution Module
965 Low Battery Cutoff and Power Switch
TRG1640 Transformer, 16.5VAC @ 40 VA
TRG2440 Transformer, 24VAC @ 40 VA

129 Computer Sound Card Interface
800 Audio Amplifier, 10 Watts
900-2 “B” Connectors,Unfilled,500 pcs
902-2 “B” Connectors,Gel filled,500 pcs
980 Telephone Line Fault Monitor
998 Warning Alarm System Decals
999 Double Sided Tape
SL1 Strobe Light, 4 colors available
WK1 Wall Mount Kit for SL1 Strobes

For more information contact your local Distributor or:
ELK PRODUCTS,INC 828-397-4200 FAX [phone]

http://www.elkproducts.com Email: [e-mail]

05/02

Magic Module Series

iButton™ Access Kit w/ MM443, MA100, MA101
iButton™ ‘Touchkey’ Reader & Interface Pack

Rust Free Sirens / Speakers

Speakers & Sirens

ECHO™ Sirens & Speakers

Siren & Voice Drivers

Surge Suppressors

Relay Modules

Power Products

Accessories

Magic Module Series

Clock/Calendar Module

ELK-MC100

APPLICATION:

The Clock/Calendar is an accessory for the Magic
Module programmable controller series. It can
be used in a vast array of Clock & Calendar
applications requiring Minute, Hour, Day, Week­day, and Monthly timing. It also provides an on­board connection for the Temperature Sensor
Module(ELK-MT100) (optional).

Magic Module Series

ELK-MC100

Clock/Calendar Module

Accessory for the ELK Magic Module

FEATURES:

•Adds Clock & Calendar Functions to the

ELK Magic Module(ELK-MM443(S)).

•Plugs into Accessory Connector(J1).

•Battery Back-Up Included.

•Daylight-Savings Time Program Option.

•Automatic Leap Year Adjustment.

•Lifetime Limited Warranty, call for details.

•On-board Connection for Temperature Sensor

Module(ELK-MT100) (optional).

SPECIFICATIONS:

•Size: 2.2" x 1.5" (60mm x 38mm).

•Operating Voltage: 9.6-15 Volts D.C.

•Current Required: 200uA.

•Battery: 3 Volt Lithium (CR2032).

REQUIRED EQUIPMENT: (not included)

•ELK-MM443 Module, 4 input, 4 output.

•Programming Software to set the clock.

Features and Specifications subject to change without notice.

828-397-4200 Voice
828-397-4415 Fax
http://www.elkproducts.com
email: [e-mail]

PO Box 100 • Hwy. 70W • Hildebran, NC 28637 • USA

Instructions Printed On Inside

MAGIC CLOCK / CALENDAR INSTRUCTIONS

D

R

The ELK-MC100 adds Clock and Calendar functions to the Magic Module(ELK-MM443) programmable
controller. This board plugs into the Magic Module Accessory Connector (J1). The 4 screw terminals on
the Clock allow for connection to an optional Temperature Sensor(ELK-MT100) which connects via a 4
conductor cable. Refer to the Temperature Sensor Instructions for more information. Figure 1 shows the
Clock plugged into a Magic Module circuit board.

Installation

Insert the flanged end of the nylon standoffs (supplied) into the holes opposite the connector and on the bottom
side of the Clock circuit board. Plug the circuit board into the white 5-pin Accessory Connector (J1) on the Magic
Module as shown in figure1. Snap in the standoffs to secure the board. Remove the paper on the battery.
NOTE: Before use, the Time and Date must be set in the Clock by using the Magic Module Software Program.
Refer to the Magic Module Development Kit for programming instructions.

ELK-MM443 MAGIC MODULE

CLOCK/CALENDAR

BOARD

J1

124816

NEGDATA CLK +5V

BLKYEL GRN RED

MOUNT CLOCK

CIRCUIT BOARD
ONTO ACCESSORY
CONNECTOR HERE

TERMINALS FOR

TEMPERATURE

DATA BUS A

JUMPE

OPTIONAL

SENSOR

MAGIC
MODULE

PRESS STANDOFFS

INTO UNDERSIDE OF

CIRCUIT BOARD HERE

BOARD

+

Figure 1. Clock/Calendar mounted on a Magic Module

Sample Real Time Clock Program for the Magic Module

This program will turn relay 1 on for 2 seconds at 8,12, and 5 o'clock PM

set EvtTMR1 Tmr1Evt
set EvtRTC RTCStart

main goto main
Tmr1Evt set OUT1 Off ;Timer1 Event (turns relay 1 off after 2 seconds)

return

RTCStart if Rhrs not= 8 RTCEvt1 ;Hour-RTC (turn relay 1 on for 2 secs if 8 o'clock)

if Rmin not= 0 RTCEvt1 ;Minute-Real Time Clock
goto RingBell

RTCEvt1 if Rhrs not= 12 RTCEvt2 ;Hour-RTC (turn relay 1 on for 2secs if 12 o'clock)

if Rmin not= 0 RTCEvt2 ;Minute-Real Time Clock
goto RingBell

-

BA

;Main Program

;return from timer 1 event

J2

12NEG 3NEG 4

RTCEvt2 if Rhrs not= 17 RTCEvt3 ;Hour- RTC (turn relay 1 on for 2secs if 5 o'clock)
RingBell set T1SEC 2 ;(set timer 1 for 2 seconds; on time for relay 1)
RTCEvt3 return ;RTCEnd

if Rmin not= 0 RTCEvt3 ;Minute-Real Time Clock
set OUT1 On ;(turns relay 1 on) connect this relay to a horn