Elkay MP20RA User Manual
GENERAL
MP20RA Surface mounting plate (Reversed) available for
installations requiring additional support. Can be secured to a
variety of load-bearing surfaces. Installation instructions
included with unit.
MP20RA Surface mounting plate (Reversed) is available as an
optional accessory for two-level Square Front models
EDFPA17RAC or Soft Sides®models EDFP217RAC or SwirlFlo
®
fountain model EDFPBM117RAC.
Elkay
2222 Camden Court
Oak Brook, IL 60523
Printed in U.S.A.
©2004 Elkay
(Rev. 1/04) 16-23A
www.elkayusa.com
MP20RA Surface Mounting Plate (Reversed)
In keeping with our policy of continuing product improvement, Elkay reserves the right to change
product specifications without notice.
This specification describes an Elkay product with design, quality and functional benefits to the
user. When making a comparison of other producers’ offerings, be certain these features are not
overlooked.
38-1/4"
(972mm)
5/8"
(16mm)
20-1/8"
(511mm)
FRONT VIEW SIDE VIEW
Surface Mounting Plate (Reversed)
MP20RA
®
SPECIFICATIONS
Elkay
2222 Camden Court
Oak Brook, IL 60523
www.elkayusa.com
Printed in U.S.A.
©2004 Elkay
16-23A (Rev. 1/04)
20-1/8"
(511mm)
5/8"
(16mm)
1/4" (6mm) DIA. HOLES FOR
MOUNTING PLATE TO WALL
BACK
PANEL
38-1/4"
(972mm)
16"
(406mm)
16"
(406mm)
16"
(406mm)
16"
(406mm)
8"
(203mm)
8"
(203mm)
2-3/4"
(70mm)
MOUNTING
PLATE
5-5/16"
(135mm)
32-1/2"
(826mm)
43-5/8"
(1108mm)
ATTACH
SURFACE
MOUNTING
PLATE TO
FINISHED
WALL
LOAD
BEARING
WALL
CONSTRUCTION
1-3/4"
(44mm)
3-1/2"
(89mm)
1-3/4"
(44mm)
3-1/2"
(89mm)
CUTOUT IN WALL FOR PLUMBING
ROUGH-INS
NOTE: REFERENCE SPECIFICATION
SHEET OF FOUNTAIN TO BE
INSTALLED FOR EXACT WASTE
AND SUPPLY LOCATIONS
FINISHED FLOOR
5/16-18 THREADS FOR
MOUNTING FOUNTAINS
TO WALL (16)
1/4-20 THREADS FOR
MOUNTING FOUNTAINS
TO WALL (12)
7/8"
(22mm)
5-5/16"
(135mm)
261/2"
(673mm)
7-7/8"
(200mm)
7/8"
(22mm)
7-7/8"
(200mm)
3/8" (10mm) DIA. HOLES
FOR MOUNTING PLATE
TO WALL (20)
1. Remove mounting plate from packaging. Read this
instruction sheet before proceeding.
These dimensions
are required to obtain proper rim and bubbler heights for
compliance with ANSI standard A117.1.
2. Install plumbing rough-ins as per fountain instructions
(supplied with fountain).
NOTE: Reference specification sheet of fountain to be
installed for exact waste and supply locations.
3. Install (2) 1/4" (6mm) screws
(not provided) into wall at
43-5/8" above finished floor. Use the two best hole locations for your application. Hang mounting plate on these
screws and level mounting plate before tightening screws.
4. Reinforce the wall in shaded areas for framed wall
construction so that it will adequately support the water
fountain. This reinforcement must support up to 300 lbs.
static load and provide a means for securing the mounting
plate in place.
5. Attach mounting plate to finished wall surface with
(12) 5/16" x 2" long bolts and flat washers, 6 per bracket
(not provided). Tighten securely. (Fastener must match wall
type, i.e. lag screws for wood studs, bolts and anchors for
masonary construction.)
MP20RA MOUNTING PLATE INSTRUCTIONS
Surface Mounting Plate (Reversed)
MP20RA
®
ROUGH-IN DIMENSIONS
Loading...