Elkay MF200 User Manual

FINISHED FLOOR LINE

SPECIFICATIONS

Two-Level Mounting Frame

Model MF200

GENERAL

MF200 Mounting Frame for use with Square Front, Soft Sides and SwirlFlo®Two-Level Water Coolers.

MF200 Mounting Frame is used on model LKTEA8C, LKTEA8RAC, LNTE8C, LNTE8RAC, LPTEA8C, LPTEA8RAC, ERHPA28C, ERHPA28RAC, ERFP28C, ERFP28RAC, ERO28C, ERO28RAC, ERPB28C, ERPB28RAC, ENOA28C and ENOA28RAC Two-Level Water Coolers.

CONSTRUCTION

16 gauge galvanized steel.

WALL OPENING

MF200 Two-Level Mounting Frame STANDARD CONFIGURATION SHOWN

HIGHER UNIT ON THE LEFT

In keeping with our policy of continuing product improvement, Elkay reserves the right to change product specifications without notice.

Elkay

www.elkayusa.com

MF200 Two-Level Mounting Frame REVERSED CONFIGURA

HIGHER UNIT ON THE RIGHT

This specification describes an Elkay product with design, quality and functional benefits to the user. When making a comparison of other producers’ offerings, be certain these features are not overlooked.

2222 Camden Court Oak Brook, IL 60523

TION SHOWN

(Rev. 12/03) 16-21A

5/16" SCREWS OR BOLTS (12 REQ’D-NOT PROVIDED)

CHILLER SHELF P/N 27638C

BOLT FRAMES TOGETHER WITH 5/16" X 3/4" (19mm) BOLTS (4 REQ’D)

HOOK RODS (2)

P/N 10-15674-43-730

SCREWS OR BOLTS (NOT PROVIDED)

5/16" HEX NUT

(4 REQ’D)

FRAME

P/N 27049C &

P/N 27050C

37-3/4"

(959mm)

4-1/2"

(114mm)

1-1/8"

(29mm)

ELECTRICAL INLET LOCATION ON CHILLER

TO FLOOR LINE

(203mm)

BACK OF WALL

TO BE 12"

(305mm)

MIN DEPTH

5-1/8"

(130mm)

FLOOR LINE

37-1/2"

(953mm)

WOOD OR STEEL FRAME SHOWN (NOT PROVIDED)

Two-Level Mounting Frame

Model MF200

REVERSED CONFIGURATION:

HIGHER UNIT ON THE RIGHT

ROUGH-IN DIMENSIONS

MAKE SURE FRAME CONFIGURATION MATCHES THE COOLER TO BE INSTALLED

STANDARD CONFIGURATION:

HIGHER UNIT ON THE LEFT

MF200 MOUNTING FRAME INSTRUCTIONS

1. Cut a square rectangular wall opening 37-1/2" (953mm)

W x 37-3/4" (959mm) H and 4-1/2" (114mm) above the floor line. These dimensions are required to obtain proper rim and bubbler heights for compliance with ANSI standard A117.1.

2. Reinforce the wall opening on all sides so that it will

adequately support the water fountain. This reinforcement must support up to 150 lbs. static load and provide a means for securing the frame assembly in place.

NOTE: Building construction must allow for adequate air flow on both sides and top of remote chiller unit. Minimum of 4" (102mm) is required.

3. Install plumbing and electrical rough-ins. A junction box

for a (3) wire, 10 amp branch circuit is provided on the inside of the chiller. (Standard 120 Volts, 60 Hz and single phase)

NOTE: Reference Specification Sheet for water cooler model to be installed for exact waste and supply locations.

Elkay

16-21A (Rev. 12/03)

2222 Camden Court Oak Brook, IL 60523

www.elkayusa.com

4. Remove frame assembly and related hardware from

packaging. Attach the two frames together thru the upright supports with (4) 5/16" x 3/4" (19mm) long bolts and nuts (provided). Tighten securely. Make sure frame configura-

tion matches the cooler to be installed.

5. Install the frame assembly squarely in wall opening with frame upright support edges flush with the finished wall face. Secure the frame to the wall thru holes with (12) 5/16"

x 2" (51mm) bolts or screws (not provided). Tighten securely. NOTE: Be sure that frame is squared in location. Do not use

less than required screw quantity and size.

6. Attach the chiller shelf support rods to the right side frame uprights at the second set of holes counting from the bottom and to the shelf at the (2) side holes. Line up the other shelf holes with the frame bottom holes and fasten the assembly to the wall using appropriately sized screws or bolts and nuts (not provided).