Elkay LRPBGRNM28K User Manual
®
SPECIFICATIONS
GENERAL
GreenSpec Listed, energy and water efficient refrigerated model.
Two-level station barrier-free stainless steel water cooler has
recess- ed in-the-wall refrigeration system and stainless steel grill.
Stain- less tubular steel support arm incorporates unique recess to
be integrated with basin. All stainless steel polished to lustrous
satin finish with high shined outer edge.
Fountain has contoured basin to minimize splashing.Flexi-Guard
StreamSaver water-efficient bubbler and easy to operate, fully
functional vandal-resistant front push button.
Flow regulator provides constant stream from 20 to 105 psi
water pressure.
Minimum 40 psi supply line pressure required in spe-
NOTE:
cial circumstances where both sides of bi-level are in use
simultaneously to ensure adequate stream height.
Energy efficient refrigeration system utilizes a combination of
tank continuous-tube type evaporator, refrigerant drier, and
capillary tube.
WATERSENTRY FILTER SYSTEM
®
Elkay Water Cooler equipped with the WaterSentry VII Filter
System, which is tested and certified to NSF/ANSI 42 and 53.
Yields a reduction of soluble and insoluble lead content to less
than 0.015mg/l. This translates to lead reduction levels of 93%
to 99%. Class 1 particulate reduction as tested per NSF/ANSI
42. Removes over 97.5% of free available chlorine which pro-
vides Class 1 performance as tested to NSF/ANSI 42. Provides
taste and odor improvement.
THIS WATER COOLER COMPLIES WITH THE REQUIRE-
MENTS OF A.D.A. (AMERICANS WITH DISABILITIES ACT)
WHEN PROPERLY INSTALLED.
NO LEAD DESIGN
THIS WATER COOLER COMPLIES WITH THE LEAD-FREE
DEFINITION IN THE SAFE DRINKING WATER ACT OF 1986
AND LEAD CONTAMINATION CONTROL ACT OF 1988.
Elkay water coolers are manufactured with a waterway system utlizing copper components and completely lead-free
material. These waterways have no lead because all lead
materials, such as leaded brass, have been removed. All
joints are brazed using silver solder only. No lead solder is
permitted. A strainer with an easily cleanable screen is provided to allow trapping and convenient removal of waterborne
particulate of 140 microns and larger prior to their entry into
the water cooler.
CAPACITIES CHART
°
GPH of 50 F Drinking Water
*
Model Base
Number Rate 70°F 80°F 90°F Watts Amps Option
LRPBGRNM(V)28K
**Based on 80 F inlet water temperature
Rated watts shown are based on operational (run) time, in compliance with A.R.I.
Standard 1010 conditions. Specific applications will determine the actual watts
consumed per hour. Watts consumed will be based on number of people served
per hour (usage), ambient temperatures and inlet water temperature.
°
Room Temperature °F
7.5 9.3 8.3 7.5 260 2.8 No 140
Full Glass
Rated Load Filler
COOLING SYSTEM
Motor Compressor: Hermetically sealed, reciprocating type
115V, 60Hz, single phase. Sealed-in lifetime oil supply.
Condenser: Fan cooled, copper tube with aluminum fins.
motor is permanently lubricated.
In keeping with our committment to continuous improvement, Elkay reserves the right to change
product specifications without notice.
Elkay
elkay.com
®
Ship .
Wt.
Lbs.
Fan
2222 Camden Court
Oak Brook, IL 60523
GreenSpec Listed Two-Level SwirlFlo
®
with WaterSentry VII Filter System
®
Barrier-Free Access
MODELS LRPBGRNM(V)28K
ene
rgy& watereff
icient
Shown Model LRPBGRNM28K
Cooling Unit: Combination tube-tank t ype. Self cleansing. Tube
portion is continuous coil of copper tubing. Tank is stainless
steel. Fully insulated with EPS foam which meets Underwriters
Laboratories Inc. requirements for self extinguishing material.
Temperature Control: Enclosed adjustable thermostat is fac-
tory preset. Requires no adjustment other than for altitude
requirements.
Refrigerant Control: Refrigerant HFC-134a is controlled by
accurately calibrated capillary tube for positively trouble-fr ee
performance.
CONSTRUCTION
Fountain Body:
steel basin polished to a lustrous satin finish with high shined
outer edge. Contoured basin offers large strike area to minimize splashing. #16 gauge, 300 series tubular support arm
incorporates unique recess to accept basin. Fully functional
vandal-resistant push button is easy to operate.
Exclusive Flexi-Guard StreamSaver Bubbler:
innovative design utilizes a pliable polyester elastomer to prevent accidental mouth injuries. Flexes on impact, then returns
to original position. Strong, abrasion-resistant. Anti-sweat.
Bubbler meets UL requirements and all sanitary codes.
Vandal-Resistant Bubbler (Option): One-piece, heavy Duty.
Front Panel Grill:
to a uniform Elkay satin finish. Removable louvered ventilating
grill encloses refrigeration unit and plumbing.
Wall Mounting Frame:
Frame allows flush mounting to finished wall.
5 YEAR LIMITED WARRANTY
the unit. Electrical components and water system are warranted for 12 months from date of installation. Sample certification available upon request.
Elkay Pressure-Type Water Coolers are designed to operate on
20 psi to 105 psi supply line pressure. If inlet pressure is above
105 psi, a pressure regulator must be installed in the supply line.
Any damage caused by reason of connecting this product to
supply line pressures lower than 20 psi or higher than 105 psi is
not covered by the warranty.
STANDARDS
This cooler is certified by WQA to lead-free compliance including
NSF/ANSI 61 and 372.
This specification describes an Elkay product with design, quality and functional benefits to the
user. When making a comparison of other producer’s offerings, be certain these features are not
overlooked.
#18 gauge, 300 series nickel bearing stainless
®
TM
Water-efficient,
Made of 300 series stainless steel, polished
MF200 frame furnished with each unit.
on the refrigeration system of
Elkay Electric Air Cooler Water Coolers are listed
by Underwriters Laboratories Inc. and comply with
both Canadian and U.S. requirements.
These units comply with A.R.I Standard 1010.
Printed in U.S.A.
©2015 Elkay
(1/15) 12-66
®
G re en S pe c®L is te d Tw o- L eve l S wir lf lo
NOTE: WATERFLOW
DIRECTION
SERVICE STOP
(NOT FURNISHED)
3/8" O.D. TUBE CONNECT
COLD WATER SUPPLY
1/4" O.D. TUBE
WATER INLET
TO COOLER
BUILDING WATER
INLET
(NOT FURNISHED)
OP ER ATION OF Q UIC K C ONNE CT F IT T ING S
VIDED)
CAL INLET
ON CHILLER
R LINE
WALL
"
TH
OGETHER
9mm) BOLTS
OVIDED)
STEEL FRAME
OT PROVIDED)
3-1/8"
With Wa te rS en tr y®VI I F il te r S ys te m
B arr ie r-F re e Ac c e s s
M od e ls LRPBGRNM(V)28K
(4 REQ'D - NOT PR
WITH 5/16" X 3/4" (1
BOLT FRAMES T
HOOK RODS (2)
FLOOR LINE
MIN. DEP
CHILLER SHELF
(305mm)
(NOT PROVIDED
TO BE 12
(130mm)
SCREWS OR BOLTS
BACK OF
5-1/8"
(953mm)
(NOT PROVIDED)
37-1/2"
(4 REQ'D)
5/16" HEX NUT
TO FLOO
(203mm)
8"
(114mm)
4-1/2"
FRAME
LOCATION
ELECTRI
(29mm)
1-1/8"
(959mm)
37-3/4"
(12 REQ'D - NOT PRO
SHOWN (N
WOOD OR
5/16" SCREWS OR BOLTS
(279mm)
FIG. 2
11"
(29mm)
1-1/8"
(114mm)
FINISHED FLOOR
4-1/2"
(203mm)
8"
ELECTRICAL INLET
(519mm)
(730mm)
20-7/16"
28-3/4"
REQUIREMENT
ADA
(686mm)
(927mm)
27"
36-1/2"
(863mm)
33-15/16"
(140mm)
5-1/2"
(1059mm)
41-11/16"
(517mm)
20-3/8"
(41mm)
1-5/8"
FURNISHED
WASTE TUBES
(41mm)
1-1/4" (32mm)
1-5/8"
(73mm)
(73mm)
(356mm)
(356mm)
2-7/8"
2-7/8"
14"
14"
BACK WALL LINE
(467mm)
(16mm)
(978mm)
18-3/8"
5/8"
38-1/2"
(121mm)
MINIMUM DEPTH
4-3/8"
(305mm)
12"
FIG. 1
(238mm)
9-3/8"
WaterSentry® VII Filter System
(206mm)
8-1/8"
(476mm)
18-3/4"
SHUT OFF VALVE BY OTHERS
WATER INLET ON CHILLER
COLD WATER OUTLET
3/8" O.D. COPPER TUBE
3/8" O.D. COPPER TUBE
(29mm)
1-1/8"
(79mm)
IM P OR T AN T !
NS TA LL E R P LE A SE N OT E :
The grounding of elec trica l equipment s uch a s telephone, c omputers , etc. , to water lines is a c ommon
proc edure. This grounding may be in the building or
may occ ur away from the building. This grounding
ca n caus e elec trical feedb ack into a water cooler,
creating a n electrolys is whic h causes a meta llic
tas te or caus es an increas e in the metal content of
the wa ter. This c ondition is a
proper ma terials as indica ted be low.
The d rain fittings which are provided by the installer
should also be plastic to electrically is olate the c ooler
from the building plumbing sys tem.
I
voidable by using the
LR PB GR NM 28K MO UNT ING FR AM E INS TR UC TIO NS
1. C ut a s quar e rec tangular wa ll open ing 37-1/2"
(476mm) W x 37 -3/4" (959mm) H and 4-1 /2"
(114mm) above the floor line. T hese dimensions
are required to obtain proper rim and bubbler
heights for compliance with ANS I s tandard.
2. R einfo rce the wall o pening on a ll side s s o that i
will adequa tely s upport the water founta in. This
reinforc ement must support up to 15 0 lbs s tatic
load and provide a means for sec uring the frame
as sembly in plac e.
NOT E: B uilding c ons truction m ust a llow for
ade quate a ir flow on both sides and top o f remote
chiller unit. Minimum of 4" (102mm) is required.
(S ee F igures 1 & 2)
3. In sta ll plumb ing a nd ele ctric al rough- ins . S ee
Figure 1 for loc ation of the suppl
chiller and for the location of the was te water
outlet. A junction box for a (3) wire, 10 a mp branc h
circ uit is p rovided on the inside of the c hiller.
(S tanda rd 120 Volts, 60 Hz and s ingle phas e)
S ee Figure 2 for the electrica l inlet loca tion.
4. R em ove f ram e a ss em bly and rela ted hardw are
from pack aging. Attach the two frame s together
thru the upright s upports with (4) 5/16" x 3/4"
(19 mm) l
Tighten s ecurely.
NO TE : Frame with higher upper channel to be on
left side.
5. In sta ll the fr ame a ss emb ly squarely in wall
opening with frame upright support e dges flush
with the finis hed wall fac e. S ec ure the frame to the
wall thru holes with (12) 5/16" x 2" (51mm) long
lag bolts or screws (not provided). T ighten securely.
NO TE : B e sure that frame is squared in loca tion.
Do
size.
6. Atta ch the chille r s helf s uppo rt rods to the right
side frame uprights at the s eco nd set o f holes
counting from the bottom and to the shelf at the
(2) side holes . Line up the other s helf holes with
the frame bottom holes and fas ten the as sembly
to the wall us ing appropriately s ized wood s crews
or bolts and nuts (not provided). (S ee Figure 2)
ong bolts and nuts (no t pro vided ).
not use less than required screw quantity and
y water inlet to
3-1/8"
Wate rSentry® V II Filter S ys tem
Flexi-Guard® Bubbler (standard)
t
(73mm)
Vandal-Resistant Bubbler (optional)
2-7/8"
14"
(356mm)
®
38-1/2"
(978mm)
4-3/8"
(121mm)
14"
(356mm)
R O U G H - I N D I M E N S I O N S
(79mm)
3/8" O.D. COPPER TUBE
COLD WATER OUTLET
12"
(305mm)
MINIMUM DEPTH
5/8"
(16mm)
5-1/2"
(140mm)
1-1/8"
(29mm)
11"
(279mm)
8-1/8"
(206mm)
4-1/2"
(114mm)
BACK WALL LINE
1-1/4" (32mm)
WASTE TUBES
FURNISHED
(203mm)
3/8" O.D. COPPER TUBE
WATER INLET ON CHILLER
SHUT OFF VALVE BY OTHERS
2-7/8"
(73mm)
20-3/8"
(517mm)
41-11/16"
(1059mm)
20-7/16"
(519mm)
FIG. 1
1-5/8"
(41mm)
1-5/8"
(41mm)
33-15/16"
(863mm)
REQUIREMENT
FIG. 2
27"
(686mm)
ADA
1-1/8"
(29mm)
18-3/8"
(467mm)
ELECTRICAL INLET
FINISHED FLOOR
®
8"
18-3/4"
(476mm)
9-3/8"
(238mm)
28-3/4"
(730mm)
36-1/2"
(927mm)
1/4" O.D. TUBE
WATE R INL ET
TO COOLER
SIMPLY PUSH IN
TUBE TO A T TAC H
3/8" O.D. TUBE CONNECT
COLD W ATE R S UPP LY
NOTE: W ATE RF LOW
DIRECTION
TUBE IS SECURED
IN POSITION
BA
E lk ay
12-66A (R ev. 1/15
PUSH IN COLLET
TO RELEASE TUBE
C
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
BUILDING W ATE R
INLET
SERVICE STOP
FRAME
5/16" HEX NUT
(4 REQ'D)
(NOT PROVIDED)
SCREWS OR BOLTS
(NOT PROVIDED
2222 Camden Court
Oa k B rook, IL 60523
elkay.com
5/16" SCREWS OR BOLTS
(12 REQ'D - NOT PROVIDED)
HOOK RODS (2)
37-3/4"
(959mm)
4-1/2"
(114mm)
37-1/2"
(953mm)
CHILLER SHELF
BOLT FRAMES TOGETHER
WITH 5/16" X 3/4" (19mm) BOLTS
(4 REQ'D - NOT PROVIDED)
1-1/8"
(29mm)
(203mm)
5-1/8"
(130mm)
FLOOR LINE
Printed in U.S .A.
© 20 15 E lkay
WOOD OR STEEL FRAME
SHOWN (NOT PROVIDED)
ELECTRICAL INLET
LOCATION ON CHILLER
8"
TO FLOOR LINE
BACK OF WALL
TO BE 12"
(305mm)
MIN. DEPTH
Loading...