Elkay LMABF8WS, LMABFDWS User Manual

EZH2O® Bottle Filling Station

With Single Filtered Mechanically-Activated Water Cooler

PRODUCT SPECIFICATION

Self-contained, wall hung refrigerated water cooler with bottle lling station. LMABF8WS shall deliver 8 GPH of 50°F drinking water at 90°F ambient and 80°F inlet water. LMABFDWS shall deliver non-chilled drinking water. Unit shall have mechanically-activated pushbar operation. Bottle lling unit shall include an electronic sensor for touchless activation with auto 20-second shut-off timer. Shall include Green Ticker™ displaying count of plastic bottles saved from waste. Bottle ller shall provide 1.1-1.5 gpm ow rate with laminar ow to minimize splashing. Shall include the WaterSentry® Plus 3000-gallon capacity lter, certied to NSF/ANSI 42 and 53, with visual monitor to indicate when replacement is necessary. Shall include integrated silver ion anti-microbial protection in key areas. Unit shall meet ADA guidelines. Unit shall be lead-free design which is certied to NSF/ANSI 61 and 372 and meets Federal and State low-lead requirements. Unit shall be certied to UL399 and CAN/CSA 22.2 No. 120.

STANDARD FEATURES

• Sanitary, touchless activation with auto 20-second shut-off (Bottle Fillter)

• Self-closing, mechanically-activated front and side pushbar controls (Cooler)

• Designed for installations where activation of cooler is needed even during power disruptions

• WaterSentry® Plus 3000-gallon capacity Filtration System, certied to NSF/ANSI 42 & 53 (Lead, Class 1 Particulate, Chlorine, Taste & Odor)

• Integrated Silver Ion Anti-microbial Protection in key areas

• Quick Fill Rate: 1.1 gpm (LMABF8WS); 1.5 gpm (LMABFDWS)

• Laminar Flow provides minimal splash

• Real Drain System eliminates standing water

• Visual User Interface display includes:

• Innovative Green Ticker™ counts bottles saved from waste

• LED Visual Filter Monitor shows when replacement is necessary

• Available with Flexi-Guard® Safety Bubbler

• Cooler panel nishes: Light Gray Granite Vinyl Clad Steel or Stainless Steel

COOLING SYSTEM (Model LMABF8WS only)

• Compressor: hermetically-sealed, reciprocating type, single phase. Sealed-in lifetime lubrication.

• Condenser: Fan cooled, copper tube with aluminum ns. Fan motor is permanently lubricated.

• Cooling Unit: Combination tube-tank type. Self-cleansing. Continuous

copper tubing with stainless steel tank. Fully insulated with EPS foam which meets UL requirements for self-extinguishing material.

• Refrigerant Control: Refrigerant R134a is controlled by accurately calibrated

capillary tube.

• Temperature Control: Easily accessible enclosed adjustable thermostat is

factory preset. Requires no adjustment other than for altitude requirements.

CAPACITIES CHART

Model Voltage / Hertz

LMABF8WS* 115V / 60Hz 8 GPH 4.0 370 75

LMABFDWS* - - 1.0 15 40

Chilling**

Capacity

F.L.

Amps

Rated Watts

Approx.

Ship

Weight.

Models LMABF8WS and LMABFDWS

RATED FOR INDOOR USE ONLY

Model LMABF8WSLK or LMABFDWSLKWSLK

CONSTRUCTION

• Stainless Steel basin with integral drain and embossed bubbler pad

• Galvanized structural steel cooler chassis provides structural integrity

• Cooler cabinet available as Light Gray Granite Vinyl Clad Steel or Stainless Steel (additional cost) construction

• Flexi-Guard® Safety Bubbler utilizes an infused anti-microbial pliable polyester elastomer to prevent accidental mouth injuries. Flexes on impact.

Replacement Filters: Available as Singles and Multi-packs. Order part numbers:

• 51300C (single)

• 51300C_3PK (three)

• 51300C_12PK (twelve)

• 51300C_24PK (twenty-four)

• 51300C_48PK (forty-eight)

CERTIFICATIONS / STANDARDS

• ADA Compliant

• UL399 and CAN/CSA 22.2 No. 120 Certied

• ANSI/NSF 61 and 372 Certied

• ANSI/NSF 42 and 53 Certied (Filter only)

• GreenSpec® Listed

*Color code of (L) Light Gray Granite or (S) Stainless Steel cooler panels **Based on 80°F inlet water & 90°F ambient air temp for 50°F chilled drinking water.

Warranty: 5 year limited warranty on the unit’s refrigeration system. Electrical components and water system are warranted for 12 months from date of installation or 18 months from factory shipment, whichever date falls rst.

In keeping with our policy of continuing product improvement, Elkay reserves the right to change

specication without notice. Please visit elkaypro.com for the most current version.

2222 Camden Court OakBrook, IL 60523

630-572-3192

elkay.com

This specication describes an Elkay product with design, quality and functional benets to the user. When making a comparison of other producer’s offerings, be certain these features are not overlooked.

SPEC00086 (09/2014)

EZH2O® Bottle Filling Station

With Single Filtered Mechanically-Activated Water Cooler

Models LMABF8WS and LMABFDWS

IMPORTANT!

This water cooler has been designed and built to provide water to the user which has not been altered by materials in the cooler waterways. The grounding of electrical equipment such as telephone, computers, etc., to water lines is a common procedure. This grounding may be in the building but may also occur away from the building. This grounding can cause electrical feedback into a water cooler creating an electrolysis which creates a metallic taste or causes an increase in the metal content of the water. This condition is avoidable by installing the cooler using the proper materials as shown below.

52 1/16"

1323mm

39 1/16" 991mm

787mm

INSTALLER PLEASE NOTE

7/16"

11mm

MOUNTING HOLES

(6)

5 3/4"

25"

21 3/8"

543mm

146mm

18 3/8"

467mm

1 3/8"

35mm

ACTIVATION SENSOR

5/16" (8mm) DIA. (5 HOLES)

31"

635mm

17 7/8"

454mm

178mm

127mm

254mm

178mm

11/16"

18mm

2 1/2"

64mm

2 7/16" 63mm

4 1/2"

114mm

10"

3 1/2"

89mm

4 9/16" 116mm

13 7/8"

352mm

1 3/8"

35mm

7 1/4"

185mm

2 9/16" 65mm

ROUGH-IN DIMENSIONS

2 5/8"

67mm

27"

686mm

ADA

REQUIREMENT

NOTICE

203mm

6 1/4"

159mm

3 9/16" 90mm

18 1/2"

471mm

HANGER BRACKET

12 5/16" 313mm

1 1/2"

38mm

6 3/4"

172mm

This water cooler must be connected to the water supply using a dielectric coupling. The cooler is furnished with a non-metallic strainer which meets this requirement. The drain trap which is provided by the installer should also be plastic to completely isolate the cooler from the building plumbing system.

Bottle Filler unit will mount on bracket attached to wall by 6 holes (as shown). Water and electrical will connect through pre-punched hole in basin.

5 3/4"

146mm

15"

381mm

3 3/16"

82mm

33"

838mm ORIFICE

HEIGHT

31 13/16"

808mm

RIM

HEIGHT

FINISHED FLOOR

18 7/8"

479mm

REDUCE HEIGHT BY 3 INCHES FOR INSTALLATION OF CHILDRENS ADA COOLER

LEGEND: A = Recommended Water Supply location. Shut-off Valve (not furnished) to accept 3/8” O.D. unplated copper tube. Up to 3” (76mm) maximum out from wall. B = Recommended Waste Outlet location. To accommodate 1-1/4” nominal drain. Drain stub 2” (51mm) out from wall. C = 1-1/4” Trap (not furnished). D = Electrical Supply (3) Wire Recessed Box Duplex Outlet. E = Insure proper ventilation by maintaining 6” (152mm) minimum clearance from cabinet louvers to wall. F = 7/16” (11mm) Bolt Holes for fastening to wall. **New Installations Must Use Ground Fault Circuit Interrupter (GFCI).

2222 Camden Court Oak Brook, IL 60523

elkay.com

Job Name: ____________________________________ Model: _______________________ Qty. ____________ Contact: ______________________________________ Approval Signature: _____________________________ Notes:

Printed in U.S.A.