Elkay LKLFHA1031NK Installation manual
SAVE FOR CONSUMER
Includes:
INSTALLATION / OWNER’S MANUAL
Harmony - Pull-Down Kitchen Faucet
LKHA1031CR
LKHA1031NK
LKLFHA1031CR
LKLFHA1031NK
NOTE: only 1 D1 washer is
1
D
used with this faucet model
Tools:
D
E
2
D
1
D
B
C
F
C
1
C
1/2”
[13 mm]
5/8”
[16 mm]
1
B
2
B
3
B
A
4
B
NOTE: these washers are not
2
used on this faucet model
13/16”
[20 mm]
WARNING: please carefully read and properly follow the instructions for installation found in this manual.
STEPS:
321
1
A
Before inse rting the single lever grou p in the hole of
the sink, make sur e that the base gasket is proper ly
positio ned in its seat and that the exible hoses are
well tighte ned to the body of the ta p.
Place th e single lever g roup in the hol e of the sink,
orienti ng the spout toward th e sink tank.
B
For counter top thicknesses less tha n 1/16” thi ck
use the rubber gasket (B1) and mounting an ge
(B2), for all other instal lations use the rubber gasket
(B1) and metal wash er (B3).
Secure mounting hardware in place by tight ening
mounting n ut (B4) with wrench (F) .
54
B
3
B
2
F
4
B
2
C
13/16”
[20 mm]
1
D
1/2”
[13 mm]
Install th e check valve (C1) to the outlet hose w ith a
rubber was her (C2).
Secure wi th wrench.
Attach t he pull-down ho se to the bottom of the
check valv e with a rubber washe r (D1).
Secure wi th wrench.
1
C
Red
Hot
Blue
Cold
2
D
Attach the c ounterweight (D2) to the exib le hose
approxim ately 15- 3/4” [400 mm] from the connect ion
to the outle t pipe.
5/8”
[16 mm]
Connect the exible hoses to the supply connect ions
with rubb er gaskets.
Secure wi th wrench.
Turn on the water an d check for leaks.
CARTRIDGE REPLACEMENT
321
1-1/8”
[28 mm]
C
B
1/8”
[2,5 mm]
Before dis sassembling the f aucet be sure that the w ater supply is turne d off.
Remove t he nish cap (A), paying a ttention not to damage it . Remove the setscrew (B) with a 1/8” [2,5mm] hex w rench. Remove the handle (C). Lift the nishing rin g nut
(D) using the reference notch . Remove the indica tor ring (E). Unsc rew the cartri dge nut (F) then pu ll out the cart ridge (G). Put the new c artridge int o the body of the fau cet,
checkin g that the two cente ring pins enter into th e respective seat s (X) and that the gaske ts on the cartri dge are well positio ned.
Reassmbl e the handle followi ng the instructi ons in reverse order.
A
F
G
E
X
D
REPLACEMENT OF THE HAND SHOWER
321
A
Remove the hand shower from its seat. Unscrew it from its cover paying attention not to
lose the ru bber gasket (A).
54
1/2”
[13 mm]
B
5/16”
C
Unscrew the bu shing con nected to the en d of t he
hose (B) pay ing atte ntion n ot to loose the r ubber
gasket (C).
[8 mm]
You can now totally remove the hose from the faucet
body and replace it with a new hose.
Reassemble the hand shower assembly by following
the instructions in reverse order.
AERATOR CLEANING / REPLACING
1
2
Separate t he hand shower cover fr om the hose.
E
Before rem oving the aerator ma ke sure that the faucet i s turned off.
Unscrew th e aerator using the ae rator installtio n key (E) included with t he faucet.
If the aerat or is clogged just r inse it with runnin g water. Do not use detergent s.
Reassemb le the aerator by follo wing the instruc tions in reverse ord er.
Loading...