Elkay LKD2432BHC Installation manual
Replacement parts available
by visiting web site
www.elkayusa.com
ELKAY LIMITED LIFETIME FAUCET WARRANTY
ON RESIDENTIAL FAUCETS
Limited Lifetime Functional and
Finish Warranty
Elkay warrants to the original consumer purchaser that the Elkay faucet purchased will
be free from defects in material and workmanship for as long as the original consumer
purchaser owns the faucet. Elkay will, at its
option, supply replacement parts (or if no
longer available a comparable product) if the
faucet fails due to a defect in material or
workmanship. This warranty does not apply
in the event of product surface damage
caused by abuse, misuse or improper care
and maintenance. This warranty excludes
damage caused by harsh or abrasive cleaners
and/or materials. This warranty excludes all
industrial, commercial and business use,
whose purchasers are hereby extended a
limited lifetime on mechanical parts and 5
years on finish. Product replacement does
not include transportation cost or labor
installation cost. Elkay reserves the right to
examine product in question and its installation prior to replacement.
OTHER WARRANTY CONDITIONS
ON FAUCETS
Our warranty does not cover product failure
or damage caused by abusive treatment,
misuse, environmental factors, improper
care and cleaning, or damage due to handling or faulty installations. This warranty is
extended only to the original consumer purchaser of the product. This warranty does
not cover shipping costs, labor costs, or any
other charges for such items as installation
or replacement of the sink, diagnosis or
replacement of any faucet or component
part, or any other expense or loss.
How to Install an
Undermount
Two-Handle Faucet
All incidental or consequential damages
are specifically excluded. No additional
warranties, express or implied are given.
Any implied warranty, including one of
merchantability or fitness for a particular
purpose, is limited to the duration of this
written warranty.
Some states do not allow the exclusion or
limitation of incidental or consequential
damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights,
and you may also have other rights which
vary from state to state.
TO OBTAIN SERVICE
UNDER WARRANTY
1. Write to: Elkay
Attention: Consumer Services
2222 Camden Court
Oak Brook, IL 60523
2. Include a letter containing the following
information:
a. Date of purchase and installation
b. Description of nature of defect
c. Model number or description of model
and/or component part if possible.
Elkay
www.elkayusa.com
2222 Camden Court
Oak Brook, IL 60523
USA
©2013 Elkay
SAVE FOR CONSUMER
0000000998 (10/13)
ELKAY•2222 CAMDEN COURT•OAK BROOK, IL 60523 USA
Install Spray and Hose (if included)
1. Remove locknut and washer from sprayer base assembly and
place assembly in far right hole of sink deck. Reassemble washer
and locknut on shank from under sink. Tighten.
2. Insert hose through sprayer base assembly then route back up
through the center hole for the faucet. Thread hose onto faucet
and tighten.
Install Faucet
1. Be sure mounting surface is clean and dry.
2. Prepare waterway; Make sure handles, cartridge nuts and flanges
are removed and the locknuts are threaded down to the bottom.
3. From under sink, insert waterway assembly up through sink faucet
drillings. From topside, Put flange gaskets on waterway, then thread
flanges onto waterway with about 1/8” of threads showing.
4. Thread cartridge nuts onto cartridges and tighten.
5. Unscrew the flanges until they are snug against the cartridge nuts.
6. From under sink, tighten locknuts against sink.
7. Place spacer ring and wedge inside waterway spout connector. (See
Change Faucet Rotation procedure)
8. Thread spout assembly on waterway and hand tighten.
9. Connect supply lines to faucet shanks and tighten.
10. Remove aerator from spout and Flush water lines to remove dirt and
sediment from water lines. Replace aerator.
SET SCREW
LOGO
TEMPERATURE
INDICATOR
RING
ALIGNMENT
SCREW
HANDLE
CARTRIDGE NUT
CARTRIDGE/VALVE
SPOUT ASSEMBLY
HANDLE
INSTALL
WEDGE
SPACER
RING
Install Handles (if required)
1. Ensure cartridge (valve) is in the “off” position. (Fully counter
clockwise for Cold and Fully clockwise for Hot.)
2. Insert handle over cartridge stem
3. Insert alignment screw in handle hole towards back of sink. Screw
in only half way.
4. Place Red Temperature Indicator Ring in the top of the hot side
handle and the Blue ring in the top of the Cold side handle.
5. Place Logo part in top of both handles so logo can be read from
front of sink.
6. Thread handle set screw into each handle and tighten.
Elkay recommends installation by a licensed plumber.
FLANGE
FLANGE GASKET
LOCK NUT
FIGURE 1
Change Faucet Rotation
1. Unscrew spout and pull upward to remove.
2. Using a finger, reach inside the waterway and pull out the wedge and
spacer ring.
3. Select the spacer ring with the desired rotation and insert into waterway.
4. Install the wedge into the waterway, making sure to align the two different
size “keys” (slots) inside the waterway with those on the wedge. (It would
help to use long nose pliers to seat the wedge, however, placing the wedge
on a finger and guiding it into the waterway also works.) Angle small side of
wedge to contact key slot first. Rest wedge in place on spacer ring. See
FIGURE 1.
5. Make sure the white wear ring is seated around the base of the spout.
Push the spout straight into the waterway, aligned 90° from handles.
6. Thread spout base onto waterway and Rotate the spout several degrees left
and right while hand tightening
Loading...