Elkay LK543C, LK543LC, LK843C, LK843LC, LK943C Installation Manual

...

Model LK960AF08C

1. Mount faucet body to wall.

2. Mount add on faucet to faucet body (see Figure 5).

3. Assemble hose to short riser (see Figure 6).

4. Assemble spray to hose (see Figure 7).

5. Attach hook to wall with screws provided.

FIGURE 6 FIGURE 7

Installation Instructions for Wall Mount and Deck Mount Pre-rinse Faucets

MODEL LK943C

MODEL LK543C

MODEL LK543LC

MODEL LK843C

MODEL LK843LC

MODEL LK943LC

MODEL LK543AF08C

MODEL LK543AF08LC

Elkay

www.elkayusa.com

2222 Camden Court Oak Brook, IL 60523

(1/12)

P99365 Rev. A

MODEL LK843AF08C

MODEL LK843AF08LC

ELKAY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 USA

MODEL LK960AF08C

MODEL LK960AF08LC

MODEL LK943AF08C

MODEL LK943AF08LC

SAVE FOR CONSUMER

PRE-RINSE ASSEMBLY

RISER PIPE

HOOK

CLAMP

Spread (open) clamp section of Hook so it will slide over Riser without marring finish of Riser. Orient Spray Head Hook with hook up and assemble to Riser. Place approximately one-half down length of Riser. Do not tighten at this time.

Assemble Spring Retainer to Riser Pipe and tighten with wrench. This will also tighten Riser Pipe on Faucet Body. Insure O-ring is in place inside of Hose Coupling prior to assembly.

ISER

PIPE

SUPPORT

SET SCREW

ALL BRACKET

ASE

ATTACH WITH SCREWS

ALL

PRING

RETAINER

CAUTION! MANUFACTURER

RECOMMENDS THE USE OF

WALL BRACKET ASSEMBLY TO

ECURE RISER PIPE ON ALL

PRE-RINSE ASSEMBLIES

Determine correct length of Support Rod from Wall to R

iser Pipe. Cut Rod to approximate size. Affix Wall Bracket Base securely to Wall and tighten securely.

NOTE: Wall Bracket should be located toward top of Riser Pipe, as close as p

ossible to Spring Retainer.

A. Assemble Large Coil Spring over Hose and onto Spring Retainer.

IMPORTANT: Spring must be assembled vertically with large curve of spring to the top.

B. Assemble Spray Head Ring over Spray Head Grip and assemble Spray Assembly to

Hose. Tighten with wrench. Insure O-ring is in place prior to assembling (see Figure

3). NOTE: Additional O-rings are provided in a plastic bag. Realign Spray Head Hook on Riser and tighten. Tighten all Wall Bracket Screws.

LARGE

COIL

SPRING

HOSE

SPRAY

HEAD

RING

SPRAY

HEAD

GRIP

HOSE

COUPLING

SPRING

RETAINER

STRAIN

RELIEF

SPRING

RISER

PIPE

POSITIVE SEAL O-RING CONSTRUCTION ELIMINATES NEED FOR WASHERS

BE SURE O-RING IS INSTALLED FOR PROPER PERFORMANCE

(Extra O-Rings are provided)

GRIP

HOSE COUPLING

SPRAY

HEAD

ASSEMBLY

SPRAY

HEAD

ASSEMBLY

RIGHT

DIRECTION

WRONG

DIRECTION

LARGE

COIL

SPRING

HOSE

SPRAY

HEAD

GRIP

General Instructions

• Turn off the water supply at the main source.

• Hand tighten all parts prior to tightening with wrench. Do not force parts together.

• Handle plated surfaces with care, being careful not to scratch with tools.

• All wall mount faucets have a 1/2" I.P.S. female flanged inlet.

• For easier assembly, you may purchase as an accessory, the LKMK462 mounting kit.

Assemble Faucet Body

Attach faucet body. For back splash mount, apply teflon tape to supply line nipples spring and attach flange fittings.

Attach body to flange fittings. For deck mount models, place the foam gasket on top of surface and attach the

combo nuts below. Tighten to be hand tight.

FIGURE 2

Assemble Faucet to Flanges

1. Assemble hook to riser

(see Figure 1).

2. Attach wall support rod

(see Figure 2).

3. Add hose, spring spray and

spring retainer as shown in Figure 3.

4. Attach pre-rinse assembly to

faucet body (see Figure 4).

5. For models with add on faucet

option, insert additional faucet between pre-rinse assembly and faucet body (see Figure 5).

FIGURE 1

FIGURE 3

FIGURE 4 FIGURE 5