Elkay LK4471LHBEVG Installation Manual

Hose Bib Fountain Accessories

Owners Manual

HOSE BIB FOUNTAIN ACCESSORIES

For Use On 4400 Series Fountains With Floor Mount Base

Hose Bib Accessory

Models 4470NLHB* & LK4470NLHB*

Locking Hose Bib Accessory

Models 4471LHB* & LK4471LHB*

Installer To assure you install this accessory easily and correctly, PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE CODES.

IMPORTANT

ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON

IMPORTANT! INSTALLER PLEASE NOTE.

THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.

PAGE 1

97886C (Rev. D - 09/15)

Hose Bib Fountain Accessories

PARTS LIST

ITEM

PART NO.

NO.

1 2 3 4 5 6 7 8

9 10 11 12

*select color option to complete part number

NS = Not Shown

*FINISH COLOR OPTIONS – Choose color option to

complete your model number, add as sufx example:

4470NLHBEVG

Matte nish: Evergreen = EVG

Gloss nish: Beige = BGE Gray = GRY Terracotta = TER Black = BLK Orange = ORN White = WHT Blue = BLU Purple = PUR Yellow = YLW Brown = BRN Red = RED

75624C 75619C

45836C*

70977C 70972C 75623C 66555C 66475C 66641C

75535C 45837C* 45838C*

75521C

DESCRIPTION

Fitting - Hose Vacuum Breaker Faucet - 1/2" NPT Panel - Access W/Bib Recess Nut - Lock 1/2" Conduit Elbow - 90° x 1/2" MPT Fitting - Tee 1/2" X 1/2" X 3/8" Tube - 1/2" O.D. X 35.00" Lg. Tube - 3/8" O.D.Tee to Strainer Tube - 1/2" O.D. X 4.38" Lg. Screw - 1/4-20 X 3/4" Torx Panel - Locking Hose Bib Door - Locking Hose Bib Bit - Pinned Torx T-27

INSTALLATION INSTRUCTIONS

1. Shut off water supply to fountain.

2. Determine location for installation of Hose Bib Accessory. Remove existing access cover plate. This accessory is designed to replace the existing access cover.

3. Disconnect the fountain water line from the main water supply. Connect Tube (Item 8) to existing fountain strainer as shown below.

4. Connect Tee (Item 6) to Tube (Item 8). Connect main water supply to Tee using 1/2" Copper Tube (Item 9). DO NOT

TURN MAIN WATER SUPPLY ON AT THIS TIME !

5. Connect Hose Bib Accessory water line to the Tee and to the Elbow (Item 5) on the Access Panel (Item 3) using 1/2" Copper Tube (Item 7) as shown below, maintain loop in coil to facilitate installation and removal of Access Panel.

6. Turn on main water supply. Check for leaks. If there are leaks, turn off main water supply and correct the water leaks as required. After insuring that all connections are leak free, leave main water supply on and replace any panels that may have been removed in the installation process.

7. Assemble Hose Bib Accessory to the main fountain body.

FOUNTAIN BODY

LOCKING HOSE BIB

(EXISTING)

FINISHED GRADE

FOUNTAIN BODY (EXISTING)

TO FOUNTAIN

REGULATOR

(EXISTING)

STRAINER

PRINTED IN U.S.A.

Halsey Taylor – halseytaylor.com Elkay – elkay.com

WATER INLET

FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816

2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523

PAGE 2

97886C (Rev. D - 12/15)