
4420BF_FTN_A LK4420BF_FTN_A
Owners Manual
Models 4420BF1U & 4420BF1L
Floor Mounted Bi-Level Bottle Filler Tubular Fountain
Models (LK)4420BF1U* Models (LK)4420BF1L*
INSTALLER
4420BF Fountains are among the easiest to install Fountains on the market today. To
assure you install these models easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR INSTALLATION
FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER APPLICABLE
CODES. After installation, leave these instructions with the Fountain for future reference.
PAGE 1
1000003685 (Rev. B - 01/18)

4420BF_FTN_A LK4420BF_FTN_A
INSTALLATION INSTRUCTIONS
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM THE
BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting structure
must be capable of supporting 300 lb. load on fountain.
2. Refer to rough-in for plumbing.
3. Install shut-off valve on water supply. (Valve not furnished)
4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished)
5. Prior to installing the bottle ller to the center mounting position of fountain, install the drain pipe (Item #11) by positioning
the short end of drain pipe through mounting plate of bottle ller. Install ller onto fountain and secure with supplied mounting
hardware.
6. Prior to installing the bottle ller to the arm mount of fountain, insert the drain pipe (Item #10) into the arm tunnel and adjust
drain to lean to the left side of arm when facing button. Install bottle ller to arm being sure drain tube is above mounting
plate of ller. Install ller onto fountain and secure with supplied mounting hardware.
7. Connect water supply and fountain drain. Connect drain waste "Tee" to fountain drain tubes. Connect outlet of "Tee" to
drainage system. Connect Bottle Filler water line to regulator with the supplied 3/8" to 1/4" reducing tting. Water connection
and drain must comply with local codes.
8. Turn on water supply and check all connections for leaks.
CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the
inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line
pressures lower than 20 PSI or higher than 105 PSI is not covered by warranty.
9. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/2" IPS. Contractor to supply waste trap and service stop
valve in accordance with local code.
10. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before
being connected to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste,
odor, color, or sediment problems.
11. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve
and the cooler. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a
positive stop, approximately 3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO PLASTIC FITTINGS AS
DAMAGE TO THE O-RINGS MAY RESULT.
1000003685 (Rev. B - 01/18)
PAGE 2

4420BF_FTN_A LK4420BF_FTN_A
4420BF1U
3"
76mm
14 9/16"
371mm
44"
1118mm
34 1/2"
877mm
33 5/16"
847mm
27 1/8"
689mm
C
2 7/8"
73mm
19"
14"
356mm
O
29"
737mm
10"
254mm
O
B.C.
12"
13mm
1/2" O (6 PL)
305mm
O
38mm
1-1/2" DRAIN
64"
1626mm
B
483mm
A
23 1/4"
590mm
FINISHED FLOOR
8"
203mm
PAGE 3
30"
762mm
LEGEND
A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT - SHUT OFF VALVE BY OTHERS
B = ACCESS PANEL ( 8" X 10" )
C = REMOVABLE BOTTOM COVER
1000003685 (Rev. B - 01/18)

4420BF_FTN_A LK4420BF_FTN_A
4420BF1L
10"
254mm
O
57 1/8"
1451mm
37 1/8"
14 9/16"
371mm
3"
76mm
943mm
27 1/8"
689mm
C
19"
14"
356mm
O
29"
737mm
B.C.
(38mm)
12"
305mm
HOLES (6 PL)
1/2"
13mm
O
O
2 7/8"
73mm
1-1/2" DRAIN
41 1/2"
1055mm
483mm
FINISHED FLOOR
A
23 1/4"
590mm
40 5/16"
1025mm
1000003685 (Rev. B - 01/18)
PAGE 4
B
8"
203mm
30"
762mm
LEGEND
A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT - SHUT OFF VALVE BY OTHERS
B = ACCESS PANEL ( 8" X 10" )
C = REMOVABLE BOTTOM COVER

15, 24
14
14
4420BF_FTN_A LK4420BF_FTN_A
15, 23
2
14
17
19
1
4
18
23
ARM ONLY 10
13
21
21
20
12
25
20
11
3
4
20
16
20
BASIN
Vandal-Resistant Bubbler
FIG. 1
12
PAGE 5
22
22
9
6
15, 24
1000003685 (Rev. B - 01/18)

4420BF_FTN_A LK4420BF_FTN_A
TROUBLE SHOOTING AND MAINTENANCE
ACTUATION OF QUICK CONNECT WATER FITTINGS:
Fountain is provided with lead-free connectors which utilize an o-ring water seal. To remove tubing from the tting,
relieve water pressure, push in on the gray collar while pulling on the tubing. (see Fig.3) To insert tubing, push tube
straight into tting until it reaches a positive stop, approximately 3/4".
1/4" O.D. TUBE
WATER INLET
TO COOLER
FIG. 2
OPERATION OF QUICK CONNECT FITTINGS
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE TO ATTACH
A B C
FIG. 3
ITEM
NO.
*select color option to complete part number
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
1000003685 (Rev. B - 01/18)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PART NO.
28467C
1000003814*
40551C
0000000325
1000003812*
1000003813*
45476C
55996C
66346C
66816C
66815C
97446C
45931C
98686C
98685C
98678C
98679C
98680C
98681C
1000003692
1000003693
98682C
1000003694
1000003695
98683C
98684C
75724C
97247C
98733C
3/8" O.D. UNPLATED COP-
PER TUBE CONNECT
COLD WATER SUPPLY
NOTE: WATER FLOW
DIRECTION
TUBE IS SECURED
TUBE IS SECURED
IN POSITION
IN POSITION
BUILDING WATER INLET
SERVICE STOP
(NOT FURNISHED)
PUSH IN COLLET
PUSH IN COLLET
TO RELEASE TUBE
TO RELEASE TUBE
FIG. 4
STREAM HEIGHT ADJUSTMENT:
B CA
PUSHING TUBE IN BEFORE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
PULLING IT OUT HELPS TO
RELEASE TUBE
RELEASE TUBE
Stream height is factory set at 35 PSI. If supply pressure varies
greatly from this, insert a small straight bladed screwdriver
through the access hole in the center of the push button and
turn the adjustment screw. Clockwise adjustment will raise the
stream and counterclockwise adjustment will lower the stream.
For best adjustment, the stream should be approximately
ITEMIZED PARTS LIST
DESCRIPTION
Basin
Cover - Round Plate
Tailpipe
Kit - Drain Plug/Gasket
Access Panel
Bottom Cover
Drain Tube
In - Line Strainer
Drain Tube
Tube - Drain (Arm Only)
Tube - Drain
Kit - Bubbler (VR)
Outdoor Bottle Filler Drain Plug
Kit - (BF) Waterway/Nipple/Gasket/Tubes/Ftgs
Kit - Hardware/Bolts/Nuts/Washers/VR Torx Screws
Kit - 1.0 GPM Regulator (BF Only)
Kit - Nozzle/Aerator/Gasket/Pin
Kit - Aerator/Key
Kit - Blank Bottle Filler Trim
Kit - LK4420BF Bottle Filler Trim
Kit - 4420BF Bottle Filler Trim
Kit - Push Button w/Blank Nameplate
Kit - Push Button w/LK4420BF Nameplate
Kit - Push Button w/4420BF Nameplate
Kit - Drain Adapter/Gasket/Nut/Washer
Kit - Drain Elbow/Gasket/Nut/Washer
Screw - 1/4"x20 x 3/4" LG. Pinned Torx
Kit - VR Screws/Bit
Kit - Regulator/Holder/Nuts
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL TECHNICAL SERVICES AT 1.800.834.4816
2222 CAMDEN COURT, OAK BROOK, ILLINOIS 60523
PAGE 6
1-1/2" above the top of the bubbler. (See Fig. 4)
5
7
15, 24
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sufx example:
4420BFEVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
See Fig. 4
8