Elkay EDFPA117C Installation Manual
EDFP A117C EDFP A1 17RAC EDFP A VR1 17C EDFP A VR117RAC
Installation/Care/Use Manual
EDFPA117C EDFPA117RAC EDFPAVR117C EDFPAVR117RAC
Swirlflo
®
Fountains with FLEXI-GUARD
®
SEE FIG . 1 OR 2
EDFPA117C
34
32
SEE FIG . 8
EDFPA117RAC
Installer
T o assure you install this model easily and correctly , PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE ST ARTING THE INST ALLATION. CHECK YOUR INST ALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER APPLICABLE
CODES. After installation, leave these instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. T O WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y OCCUR AW A Y FROM THE
BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREA TING AN ELECTROLYSIS WHICH CAUSES A MET ALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE WA TER.
THIS CONDITION IS A VOIDABLE BY USING THE PROPER MATERIALS AS INDICA TED. ANY DRAIN FITTINGS
PROVIDED BY THE INST ALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALL Y ISOLA TE THE FOUNT AIN
FROM THE BUILDING PLUMBING SYSTEM.
FIG. 1
30
FIG. 2
37
FIG. 3
23
28
29
31
10
35
16
NOTE: When installing replacement bubbler and pedestal, tighten
locknut (Item 16 or 36) only to hold parts snug in position.
DO NOT OVERTIGHTEN.
INSTALLA TION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figures 4 or 5. Shown dimensions pertain to
installation location (framing must support up to 300 lbs. weight). These dimensions are required for compliance with ANSI Standard A117.0.
2. Install rough-in plumbing as shown in Figures 4 or 5. Run the supply water inlet line through the back panel. Install a service stop (not
provided). Turn on supply water and flush thoroughly.
3. Install back panel. Place the upper edge of the panel above mounting plate on the wall. Slide the panel down until it engages the mounting plate.
Be sure back panel is firmly engaged before releasing it.
4. Remove bottom access panel from fountain basin and save the screws. Install the fountain to the back panel and wall using (4) 5/16" x 1" long
screws and washers (provided) through holes in back panel. Tighten securely.
5. Determine required length of waste line and cut to appropriate length. 1-1/4" O.D. waste tube furnished. 1-1/4" slip trap, waste elbow and
extension not provided.
6. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the strainer. Turn on water supply and
check for leaks. Newly installed water supply line should be insulated after leak check is completed. DO NOT SOLDER TUBES INSERTED
INTO THE STRAINER AS DAMAGE TO THE O-RINGS MA Y RESUL T.
7. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above 105 PSIG, a pressure regulator must be
installed in the supply line. Any damage caused by reason of connecting these products to supply line pressures lower than 20 PSIG or higher
than 105 PSIG is not covered by warranty.
8. Check stream height from bubbler. Stream height is factory set at 35 PSI. If supply pressure varies greatly from this, turn adjustment screw
on the regulator (Item 14). Clockwise adjustment will raise stream height and counter-clockwise will lower stream height. For best adjustment
stream should hit basin approximately 6-1/2" (165mm) from bubbler.
9. Replace bottom access panel to fountain using the screws provided. Tighten securely.
36
9
12
97704C (Rev. F - 12/04)
EDFP A117C EDFP A1 17RAC EDFP A VR1 17C EDFP A VR117C
EDFPA117C ROUGH-IN
FIG. 4
LEGEND:
A = WA TER INLET LOCA TION LEFT OR RIGHT SIDE. 3/8” O.D. UNPLA TED COPPER TUBE CONNECT .
B = FOUNT AIN WASTE LOCA TION LEFT OR RIGHT SIDE. WASTE IS SHOWN IN W ALL
BUT MA Y BE BEHIND W ALL. 1-1/4” O.D. DRAIN (TRAP NOT FURNISHED).
C = OPENING FOR OPTIONAL AP-99 ACCESS P ANEL.
NOTE: REINFORCE THE WALL IN THE SHADED AREAS.
97704C (Rev. F - 12/04)
PAGE 2
Loading...