EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
Installation/Care/Use Manual
Soft Sides™ Fountains with FLEXI-GUARD
EDFP217C EDFP217RAC
®
Installer
T o assure you install this model easily and correctly ,
PLEASE READ THESE SIMPLE INSTRUCTIONS BEFORE ST ARTING THE
INST ALLATION. CHECK YOUR INST ALLA TION FOR COMPLIANCE WITH
PLUMBING , ELECTRICAL AND OTHER APPLICABLE CODES. After installation, leave
these instructions inside the fountain for future reference.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WA TER LINES IS A COMMON PROCEDURE. THIS GROUNDING MA Y BE IN THE BUILDING OR MA Y
OCCUR A WA Y FROM THE BUILDING . THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK
INTO A FOUNT AIN, CREA TING AN ELECTROL YSIS WHICH CAUSES A MET ALLIC T ASTE OR AN
INCREASE IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS A VOIDABLE BY USING
THE PROPER MA TERIALS AS INDICA TED. ANY DRAIN FITTINGS PROVIDED BY THE INST ALLER
SHOULD BE MADE OF PLASTIC TO ELECTRICALL Y ISOLA TE THE FOUNT AIN FROM THE BUILDING
PLUMBING SYSTEM.
1/4" O.D. TUBE
WATER INLET
TO COOLER
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
NOTE: WATER FLOW
DIRECTION
BUILDING WATER
INLET
SERVICE STOP
(NOT FURNISHED)
FIG. 2FIG. 1
97705C (Rev. J - 8/07)
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
EDFP217C
LEGEND
A = RECOMMENDED W A TER SUPPLY LOCATION 3/8 O.D. UNPLA TED D = 1-1/4" TRAP FURNISHED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM E = 3/8" (10mm) DIA. HOLES FOR SECURING
WALL SHUT OFF BY OTHERS FOUNTAIN TO WALL
B = RECOMMENDED LOCATION FOR WASTE OUTLET F = 3/8" (10mm) DIA. SLOTS FOR MOUNTING
1-1/4" O.D. DRAIN STUBBED 1-1/2" (35mm) FROM THE WALL HANGER T O WALL
C = RECOMMENDED LOCATION FOR WASTE OUTLET G = W ALL HANGER FURNISHED LOOSE
1-1/4" O.D. DRAIN STUBBED 6-3/4" (168mm) FROM THE WALL
NOTE: REINFORCE THE WALL IN THE SHADED AREAS.
97705C (Rev. J - 8/07)
FIG. 3
PAGE 2
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
EDFP217RAC
LEGEND
A = RECOMMENDED W A TER SUPPLY LOCATION 3/8 O.D. UNPLA TED D = 1-1/4" TRAP FURNISHED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM E = 3/8" (10mm) DIA. HOLES FOR SECURING
WALL SHUT OFF BY OTHERS FOUNTAIN TO WALL
B = RECOMMENDED LOCATION FOR WASTE OUTLET F = 3/8" (10mm) DIA. SLOTS FOR MOUNTING
1-1/4" O.D. DRAIN STUBBED 1-1/2" (35mm) FROM THE WALL HANGER T O WALL
C = RECOMMENDED LOCATION FOR WASTE OUTLET G = W ALL HANGER FURNISHED LOOSE
1-1/4" O.D. DRAIN STUBBED 6-3/4" (168mm) FROM THE WALL
NOTE: REINFORCE THE WALL IN THE SHADED AREAS.
FIG. 4
PAGE 3
97705C (Rev. J - 8/07)
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
EDFP217C W/MOUNTING PLA TE
FIG. 5
LEGEND
A = RECOMMENDED W ATER SUPPLY LOCA TION 3/8 O.D. UNPLA TED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM
WALL SHUT OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET
1-1/4" O.D. DRAIN STUBBED 1-1/2" (35mm) FROM THE WALL
C = RECOMMENDED LOCATION FOR W ASTE OUTLET
1-1/4" O.D. DRAIN STUBBED 6-3/4" (168mm) FROM THE WALL
D = 1-1/4" TRAP FURNISHED
97705C (Rev. J - 8/07)
PAGE 4
NOTE:
REFERENCE SEPARA TE INST ALLA TION
INSTRUCTIONS. FOR DETAILS ON MP20
SURFACE MOUNTING PLA TE.
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
EDFP217RAC W/MOUNTING PLA TE
FIG.6
LEGEND
A = RECOMMENDED W ATER SUPPLY LOCA TION 3/8 O.D. UNPLA TED
COPPER TUBE CONNECT STUBBED 1-1/2" (38mm) FROM
WALL SHUT OFF BY OTHERS
B = RECOMMENDED LOCATION FOR WASTE OUTLET
1-1/4" O.D. DRAIN STUBBED 1-1/2" (35mm) FROM THE WALL
C = RECOMMENDED LOCATION FOR W ASTE OUTLET
1-1/4" O.D. DRAIN STUBBED 6-3/4" (168mm) FROM THE WALL
D = 1-1/4" TRAP FURNISHED
PAGE 5
NOTE:
REFERENCE SEPARA TE INST ALLA TION
INSTRUCTIONS. FOR DETAILS ON MP20RA
SURFACE MOUNTING PLA TE.
97705C (Rev. J - 8/07)
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Figures 3, 4,
5, or 6. Shown dimensions pertain to installation location (framing must support up to 300 lbs. weight).
These dimensions are required for compliance with ANSI S tandard A117.0.
2. Install rough-in plumbing as shown in Figures 3, 4, 5, or 6. Waste line should extend a minimum of 2"
(51mm) through the back panel. Run the supply water inlet line through the back panel. Install a service
stop (not provided). Turn on supply water and flush thoroughly.
3. Install back panel.
EDFP217C: Place the upper edge of the panel above hanger bracket.
EDFP217C W/MOUNTING PLA TE: Place the upper edge of the panel above mounting plate on the wall.
Slide the panel down until it engages the mounting plate. Be sure back panel is firmly engaged before
releasing it.
3. Remove bottom access panel from fountain basin and save the screws.
EDFP217C: Install the fountain to the back panel and wall using (4) 5/16" x 2" long lag bolts and washers
(not provided) through holes in back panel. T ighten securely.
EDFP217C W/WALL PLATE: Install the fountain to the back panel using (4) 5/16" x 3/4" long screws and
washers (provided) through holes in back panel. T ighten securely .
4. Remove elbow from end of p-trap and attach it to drain tube. Reattach elbow to p-trap and cut waste tube
to required length using plumbing hardware and trap as a guide.
5. Make water supply connections from service stop to the 3/8" O.D. unplated copper tube coming out of the
strainer. T urn on water supply and check for leaks. Newly inst alled water supply line should be insulated
after leak check is completed. DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS
DAMAGE TO THE O-RINGS MAY RESULT.
6. These products are designed to operate on 20-105 PSIG supply line pressure. If inlet pressure is above
105 PSIG, a pressure regulator must be installed in the supply line. Any damage caused by reason of
connecting these products to supply line pressures lower than 20 PSIG or higher than 105 PSIG is not
covered by warranty .
7. Check stream height from bubbler. S tream height is factory set at 35 PSI. If supply pressure varies
greatly from this, adjust the screw on regulator item 10 by using a small screwdriver through the small
hole in the push button item 3 (See Fig. 1 1). Clockwise adjustment will raise stream height and
counter-clockwise will lower stream height. For best adjustment stream should hit basin
approximately 6-1/2" (165mm) from bubbler.
8. Replace bottom access panel to fountain using the screws provided. T ighten securely.
TROUBLE SHOOTING AND MAINTENANCE
1. Orifice Assy: Mineral deposits on orifice can cause water flow to spurt or not regulate. Mineral deposits
may be removed from orifice with a small round file not over 1/8" diameter or a small diameter wire.
CAUTION: Do not file or cut orifice materials.
2. Stream Regulator: If orifice is free of material deposits, regulate flow according to instruction 7 stated
above.
3. Actuation of Quick Connect Water Fittings: Cooler is provided with lead-free connectors which utilize
an o-ring water seal. To remove tubing from the fitting, relieve water pressure, push in on the gray collar
while pulling on the tubing (See Figure 2). To insert tubing, push tube straight into the fitting until it
reaches a positive stop, approximately 3/4".
97705C (Rev. J - 8/07)
PAGE 6
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
FIG. 7
FIG. 8
7
6
8
9
NOTE: WHEN INSTALLING REPLACEMENT
BUBBLER AND PEDESTAL, TIGHTEN NUT
(ITEM 9 OR 20) ONLY TO HOLD PARTS SNUG
IN POSITION. DO NOT OVER TIGHTEN.
21
19
20
16
23
FIG. 9
Installing back panel: When installing back panel (item 16) without mounting plate accessory MP20 or MP20RA, attach (4)
channel braces (item 23) as shown in FIG. 9. Remove the protective backing from the tape installed on the brace. Line up
the corresponding holes in the brace and back panel and press firmly in place.
PAGE 7
97705C (Rev. J - 8/07)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
NS
NS
PAR T NO.ITEM NO.
LK464
15005C
45662C
45663C
50986C
A54874
56011C
55997C
75580C
61313C
75672C
112627543890
55996C
28782C
28783C
27959C
55000661
55000665
28250C
28252C
40045C
27057C
100322740560
15009C
45392C
56092C
28234C
70682C
27090C
EDFP217C*B EDFP217RAC EDFPVR217C EDFPVR217RAC
PAR TS LIST
DESCRIPTION
DRAIN
RETAINING NUT
PUSH BUTTON
PUSH BUTTON SLEEVE
REGULAT OR HOLDER
ORIFICE ASSY
HOUSING ASSY
PEDESTAL
BUBBLER LOCKNUT
REGULATOR
CAP SCREW
SCREW - #10-24 X .50 PHTC
STRAINER
FOUNTAIN ARM - SHORT
FOUNTAIN ARM - LONG
FOUNTAIN ARM - LONG (GLASSFILLER)
BOTTOM COVER PLATE - SHOR T
BOTTOM COVER PLATE - LONG
BACK PANEL RH ADA
BACK PANEL LH ADA
HEX NUT
REGULATOR MOUNTING BRACKET
GASKET - (VR MODEL ONLY)
BUBBLER - NIPPLE - (VR MODEL ONLY)
BUBBLER - (VR MODEL ONLY)
POLY TUBING (CUT TO LENGTH)
BRACE-CHANNEL
TEE - 1/4
BRACKET - HANGER PANEL
FIG. 10
SEE FIG. 7 OR 8
14
22
SEE
FIG . 1 1
12, 15
16
13
1
3
FIG. 11
11
417
18
10
5
2
97705C (Rev. J - 8/07)
ELKAY MANUFACTURING COMP AN Y • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
FOR PARTS, CONT ACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
PAGE 8
Loading...