ELK 6011 User Manual

ELK-6011 Wireless Single Button Panic Sensor

APPLICATION

The ELK-6011 is a Wireless Two-Way Panic Sensor. It features
a Single press and hold button and Red LED feedback indicator.
The typical application for this sensor is for activating a panic
or emergency alarm. The 6011 is compatible with Wireless
Transceivers that utilize Elk’s ‘RFTW’ two-way technology; such
as, the ELK-M1XRFTW. Each time the button is pressed and
held the 6011 sends a unique TXID identifier to the transceiver
and then listens for an acknowledgement.

The 6011 features Elk’s Industry Leading Two-Way Technology,
capable of on-demand status updates as well as extended range
and long battery life.

SPECIFICATIONS:

Frequency: 902 Mhz - 928 Mhz frequency hopping
Dimensions: 1.43”W x 1.9”L x .53”D
Operating Temperature: 14° to 104° F (-10° to 40° C)
Relative Humidity: 5-95% Non-Condensing
Battery: Non-Replaceable, est. 5 yr life based on typical use
Unique TXID Code

Enrolling from M1 Keypad Installer Programming

1. Enter M1 Keypad Installer Programming and navigate
to Menu: 14-Wireless Setup

2. Press right arrow, then scroll up to Sub-Menu: 3:Learn Sel

WirelessTransmtr

3. Press right arrow, then scroll or select a unused/available
WZone (wireless zone).

4. Press right arrow to Lrn (Enroll) a new sensor.
Press and hold the single button as soon as the M1 Keypad

5.
displays Push Transmitter Button. The M1G voice will
speak; “Press Transmitter button for zone xx”.

6. Upon successful enrollment the Keypad will chime and
briefly display the 6 digit TXID code of the sensor.
If enrollment fails the TXID will not display. If that occurs;
repeat steps 3 thru 6.

7. The Rapid-Enroll feature will auto advance to the next
wireless zone in sequence and wait for the next enrollment.
Simply repeat step 5 for each additional Keychain Remote.

8. To end Rapid-Enroll AFTER all wireless zones (sensors)
are enrolled, press the ELK key one time.
Setting the Loop # - For Keychain remotes the Loop # setting

9.
does not matter!

10. No-Supervision - Press the ELK key to locate Sub-Menu:
2: Xmit Transmitter Opt. Press the right arrow and scroll
to the wireless zone belonging to the Keychain Remote.
Press the right arrow and scroll up to option 02. Press the
right arrow and enter “0” for No Supervision. NOTE:
Keychain Remotes are not supervised. They DO NOT send
supervisory check-in signals to the transceiver!

ZONE DEFINITION: After all wireless zones (sensors) have
been enrolled proceed to Menu: 5 - Zone Definitions to
program the name, zone type, and any desirable options.

Program the Zone Definition for a 6010 KeyChain Remote
as: 15-Keyfob.

IMPORTANT! The program option for supervision must be set to NO on any wireless zone(s) used with Keychain Remotes.
These type of devices are commonly carried off-premises in a pocket or purse. Because of this, Keychain Remotes are not
designed to send supervisory check-in signals since they will often be out of operating range of the Wireless Transceiver.
Should the control ever display a “Missing Transmitter” trouble on a Keychain Remote zone, it quite possible that the
supervisory option is set wrong. Make sure the supervisory option is set to NO.

Enrolling from ElkRP Software

1. Launch ElkRP and open the desired Customer Account file.

2. If no wireless zones currently exist in this M1 you will need
to create a group of 16 wireless zones. In the folders column
right click on Zones (Inputs) and then click New Wireless
Zones. Place a check mark in the box beside the desired
group, then click OK. Repeat if additional wireless groups
are required. All expanded zones must be defined in groups
of 16. The M1XRFTW wireless must always start at Zone
17 (Group 2) and the last wireless zone CANNOT be higher
than Zone 160 (Group 10).

Note: M1 only allows Zones 17 to 160 to be used for
wireless zones (max. of 144 wireless sensors). If a large
number of wireless zones is expected, avoid conflict with
any future Hardwired Zones in the range of zones 17 to
160 by NOT enrolling any Hardwired Zone Expanders
(M1XIN) at data bus addresses below 10.

3. Double click on Wireless - Group _ (the group just added),
then double click one zone at a time to define a name, type,
and options. Repeat for each wireless zone. In ElkRP it is
more efficient to program the Zone Definitions (name, type,
and options) before moving on to the Wireless Setup for
entering the TXID and Loop number.

4. From the Folders column double click on Wireless Setup
to setup and enroll the wireless sensors.

4a. Click the Transmitters tab, then double click a zone.
4b. Place a check mark in the Enabled box.
4c. Set Supervision type to 0 - Keychain Remotes are Not

Supervised.

4d. Skip to the TXID box and enter the Sensor TXID from the

printed label located on the sensor.

4e. LOOP # - For Keychain remotes the Loop # setting does

not matter!

4f. Click Save. Repeat the entire step 4 for each additional

Wireless Zone and Sensor.

Front Page

The 6011 has a single activation button. Pressing and holding this button for at least 2 seconds will cause a wireless Keyfob
event 4 activation to be transmitted to the M1 Control. Wireless Keyfob event 4 must be programmed as a 24hr Police Panic
alarm. Refer to the M1 Keypad Installer programming menu [Wireless Setup > Keyfob Defintions] or the ElkRP Software.
While the button is held, and continuing for approximately 5 seconds, the single Red LED on the 6011 should blink to confirm
that the 24hr Police Panic alarm has been activated.

RED Button - Pressing and holding this button for 2 seconds will activate the wireless Keyfob event definition 4. The default

definition of wireless Keyfob event 4 is 0000 [blank]. This event MUST be programmed in order for this button to function.

NOTES: A special M1 firmware update is required to support keychain remotes assigned to partitions (Areas) 2 thru 8.
If the M1 Transceiver experiences a total power loss the status displayed for partitions 2 thru 8 will be incorrect until
such time as a keychain remote is used to physically change the partition status. ** Whenever the keychain remote is
transmitting you may notice the LED faintly flicker, especially in dark or low light conditions. This is normal.

Operational Testing

1. The ELK-6011 Wireless Single Button Panic Sensor must be within range of the Wireless Transceiver.

2. Press and hold the button for at least 2 seconds. Continue holding.

3. The 24hr Police Panic alarm should activate on the M1 Control.

4. The LED above the pushbutton should start to blink RED, indicating that the 24hr Police Panic has been activated.

IMPORTANT NOTICES: Per UL a complete test of the security system and all zones should be performed once a week.
Wireless devices cannot operate beyond the range of their Transceiver(s). If the Elk-6011 does not activate the alarm,
or the LED visual feedback does not work, it is likely that the sensor is out-of-range of the Transceiver. Other causes
include: 1) not properly enrolled, 2) low or dead battery, or the M1XRFTW Transceiver is disconnected or not working
and able to hear and respond.

Battery

The 6011 Keychain Remote battery is not-replaceable. When
the battery reaches end-of-life it will be necessary to replace the
Keychain Remote. The system will display a low battery alert
prior to the end-of-life.

BATTERY WARNING: Risk of fire, explosion and burns. Do not attempt to disassemble. Do not incinerate or expose to heat
above 212° F (100° C). Dispose of used sensor and its battery properly. Keep away from children.

This device complies with Part 15 of the FCC Rules and Industry Canada License-Exempt RSS Standards. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that
may cause undesired operation.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the
transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication.

ELK-6011 Wireless Single Button Panic Sensor FCC ID: TMAELK-6011

NOTE: ELK PRODUCTS IS NOT RESPONSIBLE FOR ANY CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY
RESPONSIBLE FOR COMPLIANCE. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

NO LED = Out of Range

PO Box 100 3266 US Hwy 70 West
Hildebran, NC 28637
Ph 828-397-4200 Fax [phone] http://www.elkproducts.com

Limited Warranty

The 6011 Wireless Single Button Panic Sensor is warranted to
be free from defects and workmanship for a period of 2 years
from date of manufacture. Batteries used with wireless devices
are not warranted. Elk makes no warranty, express or implied,
including that of merchantability or fitness for any particular
purpose with regard to batteries used with wireless devices.
Refer to Elk’s website for full warranty statement and details.

FCC AND IC COMPLIANCE STATEMENT:

Printed In USA

L648 10/03/2013