Eliwell IC 901 User Manual

THE USER INTERFACE

The user has a display and four keys for
controlling status and programming of the
instrument.

KEYS AND MENUS

UP key Scrolls through the menu items

Increases the values

DOWN key Scrolls through the menu items

Decreases the values

FNC key ESC function (exit)

SET key Accesses the setpoint

Accesses the menus
Confirms the commands

The instrument has two main menus: the
“Machine Status” and “Programming”
menu.

ACCESSING AND USING MENUS

The instrument is programmed by menus.
To access a menu, press and quickly
release the “SET” key (“Machine status”
menu) or press the “SET” key for over 5
seconds (“Programming” menu).
To access the contents of each folder, indi­cated by the relevant label, just press the
“SET” key once.
You can now scroll through the contents
of each folder, modify it or use its func­tions. If you do not use the keyboard for
over 15 seconds (time-out) or if you pres­ence the “FNC” key once, the last value
shown on the display is confirmed and you
return to the previous screen mask.

MACHINE STATUS MENU

To access the “Machine Status “menu,
press and quickly release the “SET” key.
The “Set” folder label appears. To view the
Setpoint value, press the “SET” key again.
The Setpoint value appears on the display.
To change the Setpoint value, use the “UP”
and “DOWN” keys within 15 seconds.
If the parameter is LOC = y the Setpoint
cannot be changed.

PROGRAMMING MENU

To enter the “Programming” menu, press
the “SET” key for more than 5 seconds.
If specified, the access PASSWORD will be
requested, (parameter “PA1”), and the
label of the first folder will follow.
To scroll through the other folders, use
the “UP” and “DOWN” keys.
To enter the folder, press “SET”. The label
of the first visible parameter appears.
To scroll through the other parameters,
use the “UP” and “DOWN” keys. To change
the parameter, press and release “SET”
then set the desired value with the “UP”
and “DOWN” keys, and confirm with the
“SET” key, to move to the next parameter.

COPY CARD

The Copy Card is an accessory that con­nected to the serial door TTL permits both
fast programming of instrument’s parame­ters (download), and the possibility to save
the instrument’s parameters (upload) in
order to use them to ri-program other
equivalent instruments. To do this opera­tion enter the folder identified from
label “FPr” and use parameters “UL” or
“dL” depending on the case; to start
uploading (downloading) simply press
“SET” button.

KEYBOARD LOCKING

The instrument includes a facility for dis­abling the keyboard, by programming the
“Loc” parameter (see folder with “Dis”
label). If the keyboard is locked, you can
still access the programming menu by
pressing the “SET” key.
The Setpoint can also be viewed.

DIAGNOSTICS

The alarm condition is always signalled by
the buzzer (if present) and by the led of
the alarm icon
The alarm signal produced by a faulty
room probe (probe 1) is shown as E1 on
the instrument display 1.

INSTALLATION

The instrument is designed for flush panel
mounting. Insert the unit through a
71x29 mm panel cut-out and affix with the
U-bracket supplied.
Select a location which will not be subject
to high humidity or condensation and
allow some ventilation to provide cooling
to the instrument.

ELECTRICAL
CONNECTIONS

Attention! Never work on electrical con­nections when the machine is switched on.
The instrument is equipped with screw ter­minal boards for connection of electrical

cables with a diameter of 2.5 mm

2

(one
conductor only per terminal for power
connections). For the capacity of the ter­minals, see the label on the instrument.
Relay outputs are voltage free. Do not
exceed the maximum permissible current
– in case of higher loads, use a contactor
of adequate power. Make sure that the
supplied voltage matches the values speci­fied for the instrument.
In the versions supplied on 12V, the power
supply must be provided via a safety trans­former protected by a 250 mA delayed
fuse. The probes do not have any insertion
polarity and can be lengthened by using a
normal bipolar cable (note that if the
probes are lengthened, this will affect the
behaviour of the instrument in terms of
EMC electro-magnetic compatibility –
wiring must be done with great care).
We advise you to keep the probe and sup­ply cables well away from the power
cables.

CONDITIONS OF USE

PERMITTED USE

For safety reasons the instrument must be
installed and used according to the
instruction provided and in particular,
under normal conditions, parts bearing
dangerous voltage levels must not be
accessible.
The device must be adequately protected
from water and dust as per the application
and must also only be accessible via the
use of tools (with the exception of the
frontlet).
The device is ideally suited for use on
household appliances and/or similar refrig­eration equipment and has been tested
with regard to the aspects concerning
European reference standards on safety.

IC 901

electronic thermostat with single output

fnc

set

LED

Position Associated function Status

Relay 1 ON for relay ON, flashing for delay, disabled protection

or activation

Alarm ON for an active alarm

It is classified as follows:
o according to its manufacture: as an
automatic electronic control device to be
incorporated by independent mounting;
o according to its automatic operating fea­tures: as a 1 B-type operated control type;
o as a Class A device in relation to the cat­egory and structure of the software.

USE NOT PERMITTED

Any other use other than that permitted is
de facto prohibited. It should be noted
that the relay contacts provided are of a
practical type and therefore subject to
fault. Any protection devices required by
product standards or dictated by common
sense due to obvious safety reasons should
be applied externally.

LIABILITY AND RESIDUAL
RISKS

Invensys Controls Italy S.r.L. shall not be
liable for any damages deriving from:

- installation/use other than that pre­scribed and, in particular, that which does
not comply with safety standards anticipat­ed by regulations and/or those given here­in;

- use on boards which do not guarantee
adequate protection against electric shock,
water or dust under the conditions of
assembly applied;

- use on boards which allow access to dan­gerous parts without the use of tools;

- tampering with and/or alteration of the
products;

- installation/use on boards not complying
with the standards and provisions of cur­rent legislation.

DISCLAIMER

This publication is the exclusive property
of Invensys Controls Italy S.r.L. who
absolutely prohibits its reproduction and
distribution unless expressly authorised by
Invensys Controls Italy S.r.L.
Although great care has been taken with
regard to the preparation of this docu­ment, Invensys Controls Italy S.r.L. does
not assume any responsibility whatsoever
in relation to its use.

The same applies to every individual and
company involved in creating and drawing
up this manual. Invensys Controls Italy
S.r.L. reserves the right to make any
amendment, esthetical or functional, with­out giving prior notice and at any time.

TECHNICAL DATA

Frontal panel protection: IP65.
Container: plastic body in resin type
PC+ABS UL94 V-0, inspection window in
polycarbonate, buttons in thermoplastic
resin.
Dimensions: frontal panel 74x32 mm,
depth 60 mm.
Installation: on panel, with template 71x29
mm (+0.2/–0.1 mm).
Ambient temperature: –5…55 °C.
Storage temperature –30…85 °C.
Operating environment humidity: 10…90%
RH (non condening).
Storage environment humidity: 10…90% RH
(non condensing).
Viewing range: –50…99 °C on 2 digit +
mark display.
Analog inputs: one PTC or NTC input
(selectable through parameter).
Digital outputs: one relay output, SPDT
8(3)A 250Va relay or SPDT 15A(1hp)

250Va relay (for capacity relay see label
on the instrument).

Measuring range: from –50 to 99 °C.
Precision: 0.5% better than full scale.
Resolution: 1 °C.
Consumption: according to model.
Power supply: according to model.
See label on instrument.

ID 901 2/2

Invensys Controls Italy s.r.l

via dell'Industria, 15 Zona Industriale Paludi
32010 Pieve d'Alpago (BL) ITALY
Telephone [phone]
Facsimile [phone]
Internet http:/www.climate-eu.invensys.com

1/2002 ing
cod. 9IS22048