Page 1
Electric Wall/Ceiling Projection Screen
Starling Series
User’s Guide
Important Safety & Warning Precautions
Make sure to read this user’s guide and follow the procedures below.
Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra Black Top Drop
in the roller. Please be aware of this as it will void your warranty with Elite Screens. Unapproved changes or
modifications (except for cutting the power cord for hardwire installations) to this unit are prohibited and will void
your warranty. For more information, please contact our Technical Support Dept. at (877) 511-1211 Ext. 604.
Please retain this user’s guide for future reference.
To avoid damaging the unit, do not use with any unauthorized accessories not recommended by
the manufacturer.
Handle the unit carefully during transportation to avoid any damages.
To ensure safe and reliable operation, direct connection to a properly grounded power source is
advised.
The power outlet supplying power to the unit should be close to the unit and easily accessible.
Do not install the unit on uneven or inclined surfaces.
Do not put heavy objects on the power cord and position it properly to avoid creating a trip
obstacle.
Never overload the power cord to prevent an electric shock or fire due to a loose contact or a
short circuit.
There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by
yourself. No one except authorized technicians can open and make repairs to this unit.
Make sure the power source this unit is connected to has a continuous power flow.
If there is need to use an extension cord, make sure the cord has an equal rating as the appliance
to avoid overheat.
Do not handle the power plug when your hands are wet or your feet are in contact with water.
Do not use this unit under the following circumstances.
Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.
Avoid direct Sunshine, rain shower and moisture.
Keep away from fire sources and high temperature to prevent this device from overheating.
Cut off the power supply first before transportation or maintenance.
Fully disconnect from the power supply when the unit is not in use for a long period of time, as
should be done with any other electric household appliance.
To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is
obvious damage or if there are any evident broken parts.
V010914-JA www.elitescreens.com 1
Page 2
Pre-Installation
A. Pair of Brackets x1
B. Steel Expansion Concrete
Anchor Hook x 2
C. Spring Snap Link x 2
D. Steel Expansion
Concrete Anchor x 4
E. ST5x40 Self-drilling screws x 4
F. Plastic expansion dry-wall
anchor x 4
G. M6x16 screw x 4
H. M6 nut x 4
(Left)
(Right)
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
particles such as dust, sawdust, and/or liquids.
Installation Warning
Due to various installation environments, the instructions provided in this user’s guide are for reference
only. Please consult a professional installation company for further installation and safety advice. The
installer must insure that proper mounting hardware is used to provide adequate strength suitable for
the installation. Elite Screens is not liable for any faulty installations.
Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures.
Reorient or relocate the receiving antenna of the device which may be casing the interference.
Increase the separation between the screen and the device’s receiver.
Connect the equipment into a different power outlet other than the device.
Note
Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location.
Hardware Parts List for the Starling Series
Please make sure all parts listed below are included before proceeding with the installation.
V010914-JA www.elitescreens.com 2
Page 3
Installation Instructions
A. Wall Mount
I. Flush mount using end caps
II. Flush mount using brackets
B. Ceiling Mount
I. Flush ceiling mount using brackets
II. Suspended
Low ceilings
High ceilings
1. Measure and mark the distance
end cap.
2. Drill a hole on each
into wall
3. Hang the screen
Side view
Screen-to-wall installation with brackets
Side view
Ceiling
Ceiling
1. Attach the brackets to the end caps with the M6x16 screws and M6 nuts
4. Hang the screen.
Ceiling
Ceiling
Ceiling
Ceiling
Screen-to-ceiling installation with brackets
1. Attach the brackets to the end caps with the M6x16 screws and M6 nuts
4. Secure the screen by inserting the screw into each bracket hole to complete your installation.
1. Measure and mark the distance between each
2. Drill a hole and install the expansion anchor hook
4. Hang the screen from the anchor hook
Screen-to-wall installation
Low Ceiling
Ceiling
End cap ear
1. Measure and mark the distance between each
2. Drill a hole and install the expansion anchor hook
and snap link to hang your screen
End cap ear
Steel wire not
purpose only)
C. Hidden Mount
A. Wall Mount, I
A. Wall Mount, II
B. Ceiling Mount, I
B. Ceiling Mount, II
between the keyholes on each side’s
2. Measure and mark the distance between each bracket’s top screw hole
3. Drill a hole for each top and bottom screw hole and insert screws into wall.
side and insert screws
2. Measure and mark the distance between each bracket’s screw hole
3. Drill a hole for each screw hole
screw hole on end cap ear
3. Attach the snap link to the end cap ear
screw hole on end cap ear
3. Attach the snap link to the end cap ear
4. Connect a chain or steel wire to the anchor hook
V010914-JA www.elitescreens.com 3
included
(for illustrative
Page 4
Standard Accesories for Starling Series
A. RF remote
B. IR remote
Up
IR sensor
Operation
Electric current: The screen operates on AC110V at 60hz
1. Plug the screen’s power cord to a power outlet.
2. Once the screen has power you’ll be able to control it with the Infared or Radio Frequency remote and
the Wall switch box.
Control System
The Starling Series has Infrared and Radio Frequency receivers. You can control the screen’s
UP/STOP/DOWN positions utilizing either the IR (Infrared) or RF (Radio Frequency) remotes.
1. IR remote control
The IR remote control requires line-of-sight to the IR sensor. Make sure to point the IR remote directly to
the IR sensor located on the wall switch box.
Note: a. The IR remote has a range of 15 feet.
b. The IR sensor must not be covered or blocked.
2. RF remote control
The RF remote does not require line-of-sight and can be used up to 50ft.
Press the Down button to Drop the screen
Press the Stop button to Stop the screen
Press the UP button to Retract the screen
3. Wall switch box
The UP/STOP/DOWN control buttons are located on the side of the box.
Stop
Down
For a local Elite Screens contact or Technical Support, please
visit www.elitescreens.com
V010914-JA www.elitescreens.com 4
Loading...