Elite Screens Saker Tension Series User Manual

051215-JA 1 www.elitescreens.com

Electric Wall/Ceiling Projection Screen

Saker Tension Series

User’s Guide

Important Safety & Warning Precautions

Make sure to read this user’s guide and follow the procedures below.

Caution: The screen’s Black Top Drop is already set to its maximum drop distance. There is NO extra
Black Top Drop in the roller. Please be aware of this as it will void your warranty with Elite Screens.
Unapproved changes or modifications (except for cutting the power cord for hardwire installations) to this
unit are prohibited and will void your warranty.

• Please retain this user’s guide for future reference.

• To avoid damaging the unit, do not use with any unauthorized accessories not recommended by the

manufacturer.

• Handle the unit carefully during transportation to avoid any damages.

• To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

• The power outlet supplying power to the unit should be close to the unit and easily accessible.

• Do not install the unit on uneven or inclined surfaces.

• Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

• Never overload the power cord to prevent an electric shock or fire due to a loose contact or a short

circuit.

• There are not user serviceable parts in this unit. Do not attempt to disassemble this unit by yourself.

No one except authorized technicians can open and make repairs to this unit.

• Make sure the power source this unit is connected to has a continuous power flow.

• If there is need to use an extension cord, make sure the cord has an equal rating as the appliance to

avoid overheat.

• Do not handle the power plug when your hands are wet or your feet are in contact with water.

Do not use this unit under the following circumstances.

• Disconnect the power cord under the conditions of heavy rain, wind, thunder or lightning.

• Avoid direct Sunshine, rain shower and moisture.

• Keep away from fire sources and high temperature to prevent this device from overheating.

• Cut off the power supply first before transportation or maintenance.

• Fully disconnect from the power supply when the unit is not in use for a long period of time, as

should be done with any other electric household appliance.

• To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is

obvious damage or if there are any evident broken parts.

051215-JA 2 www.elitescreens.com

WARNING

The Screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra top black
drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Individual modifications to this product are prohibited and will void the warranty with the manufacturer.
Please contact Elite Screens Customer Service for any questions.

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that the interference will not occur on a particular installation. If this
equipment causes harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.

 Reorient or relocate the receiving antenna of the device which may be causing the

interference.

 Increase the separation between the screen and the device’s receiver.
 Connect the equipment into a different power outlet other than the device.

Pre-Installation

1. Carefully unpack the screen.

2. Always handle the screen in a leveled position on a clean surface.

3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign

particles such as dust, sawdust, and/or liquids.

NOTE

Regardless of the mounting method, the screen should be securely supported so that the vibration or
pulling on the viewing surface will not cause the casing to become loose or fall. The installer must insure
that the fasteners used are of adequate strength and suitable for the installation location.

Hardware Parts List

Please make sure all parts listed below are included before proceeding with the installation.

A. Wall/Ceiling mount

bracket x2

B. M4x50 Screw x4 C. M10 Dry-wall

anchor x4

D. Bracket

connector x2

E. M5x15 Bolt

Screw x4

F. M5x25MM round
head cross screws x2

G. M5x30MM eyebolt

screw & M5 nut x2

H. Hidden wall

bracket x2

I. R18xR6x1 washer

x4

J. Snap link x2