Elite Screens ITE84VW2-E30, ITE84HW2-E30, ITE100HW2-E24, ITE106HW2-E24, ITE120HW2-E20 User Manual

In-Ceiling Front Projection Screen

Evanesce Tension Series

User’s Guide

Rev.012710-JA

[e-mail] [e-mail]

1

Important Safety and Warning Precautions

Be sure to read this user guide before use and follow the procedures below.

 Please retain this manual for future reference.
 To avoid any damage, do not use in conjunction with any accessories not recommended by the

manufacturer. Handle the device carefully during transportation to avoid damage.

 To ensure safe and reliable operation, direct connection to a properly grounded power source is

advised.

 The power outlet supplying power to the unit should be close to the unit and easily

accessible.

 Do not install the device on uneven or inclined surfaces.
 Do not put heavy objects on the power cord and position it properly to avoid creating a trip

obstacle.

 Never overload the power cord to prevent an electric shock or fire.
 Guard the device from any liquid or foreign objects to avoid electrical shock or fire due to loose

contact or short circuit.

 There are no user serviceable parts in the device. Do not attempt to disassemble this device by

yourself. No one except authorized technicians can open this device to make repairs.

 Make sure the power source this device is connected to has a continuous power flow.
 If there is a need to use an extension cord, make sure the cord has the same equal rating as the

appliance to avoid overheat.

 Do not handle the power plug when your hands are wet or your feet are in contact with water.

2. Do not use this device under the following circumstances:

 Disconnect the power cord under the conditions of heavy rain, wind, thunder or lighting.
 Avoid direct sunshine, rain shower or moisture.
 Keep away from fire sources and high temperature to prevent this device from overheating.
 Cut off the power supply first before transportation or maintenance.
 Fully disconnect from the power supply when screen is not in use for a long period of time, as

should be done with any other electric household appliance.

To avoid possible injury and/or an electric shock, do not attempt to use the screen if there is obvious damage or if
there are any evident broken parts

2

Warning

Evanesce Tension Standard Accessories

Red 1 2V (+)

Green 0V (-)

E. 5-12 volt trigger adaptor cable

G. AAA

Batteries

A. IR Remote B. RF Remote

C. 3-way switch D. IR ”eye” receiver

F. Bubble level

The screen’s Top Black Drop is already set to its maximum drop distance. There is NO extra black top
drop in the roller. Please be aware of this as it will void the limitation of your warranty.

Changes or modifications (except cutting the power cord for hardwire installation) to this unit not expressly
approved by Elite Screens is prohibited and will void the warranty.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause harmful interference to
radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures.

 Reorient or relocate the receiving antenna of the device which may be causing interference
 Increase the separation between the screen and the device’s receiver
 Connect the equipment into a different power outlet than the device’s
 Consult the dealer or an experienced Radio/TV technician for help

75

3

1. 5-12V Trigger: The built-in 5-12V trigger
input for your new CineTension2 allows your screen
to synchronize its drop and rise with the projector's
power cycle. The screen drops when the projector
powers up and retracts when the projector powers
down. The 5-12 volt adaptor connects to your
projectors trigger output via a separate cable that may
or may not be provided by the projector manufacture.
The trigger feature will not work without an output
cable from the projector, but it can be tested using a
9-volt battery by simply connecting the Red (+) and
Green (-) cable to the 9-volt battery.

2. 3-way switch and IR (Infrared) Eye Receiver: The 3-way Wall Box switch enables the consumer to manually operate
the screen's drop/rise capabilities. The IR “eye” protrudes from the bottom of the casing to present a low profile line-of-sight
control option for your IR remote. It is a low-visibility alternative to using the 3-wall switch and its ability to protrude from
the bottom of the screen allows line-of-sight control even in a recessed ceiling installation.

3. Infrared (IR) and Radio Frequency (RF) Remote Controls: Although the IR remote requires a direct line of sight

with the IR sensor to function, the screen’s case can be hidden from sight and operated using the RF remote. When

depressing the directional buttons you should hear a faint click signifying that the mechanism is working properly.

** Please remember to always point to the wall switch receiver when using the IR remote. The IR remote can also work with a
Universal Learning Remote Control usually by programming the Screens IR codes into your Universal Learning Remote.

This is the IR remote
with a range of 25 Ft.
Requires 2x AAA
batteries.

UP

St op

IR RF

This is the RF remote
with a range of 100 Ft.
Requires 2x AAA
batteries.

RJ-45 input for 5-12 v

5-12V RJ-45 cable