ELITE SCREENS Aeon Edge Free 16:9 frameless fixed frame projector screen 92"" cinewhite (AR92WH2), Aeon Edge Free 16:9 frameless fixed frame projector screen 100"" cinewhite (AR100WH2), AR110WH2, AR135WH2, AR120WH2 user_guide_aeon_cg3_Spring.pdf

1. Frame and Edge TrimParts List

Qty

item

Qty

item

vertical frame

½ horizontal frame

½ horizontal frame

Aeon Series

EDGE FREE® Ambient Light Rejecting Fixed Frame Screen

USER’S GUIDE

Version 2 (Spring type)

Product Description:

The Aeon Series is a fixed frame projection screen that uses Elite’s EDGE FREE® technology. The EDGE
FREE® design resembles a giant size flat panel TV display. The Aeon includes a bezel trim to further
enhance the frame appearance and absorb projector overshoot.

The screen material included is our CineGrey 3D ambient light rejecting material, which is a front
projection material precisely formulated for environments with minimal control over room lighting. It was
designed to enhance picture brightness, offer accurate color fidelity, and improve contrast levels. The
CineGrey 3D is best for family rooms, educational facilities, conference rooms or any applications in which
incident light is a factor.

In order for the CineGrey 3D to maintain its projection qualities and optimum performance, please refer to
the list below for proper maintenance and cleaning.

• Use a dry microfiber cloth to remove dust from the screen’s surface.

• When cleaning, use a damp microfiber cloth with warm water to remove any marks.

• Never rub or apply pressure when cleaning the surface.

• Never attempt to use any solutions, chemicals or abrasive cleaners on the screen surface.

• In order to avoid damaging the screen, avoid touching it directly with your fingers,

pens/pencilsor any other sharp or abrasive objects.

Part

A.

2 pcs

Main Frame Parts

Part

D.

2 pcs

Edge Trim Parts

Part

B.

Part

C.

V071116-ESA www.elitescreens.com U-00017 1

Part

E.

Part

F.

2. Hardware Parts List

a.

b.

c.

d.

e.

f.

g. h.

i

j.

k.

l.

m.

a.

Center Joints (1)

4 4 4 4 4 4 4 4 4

d.

Spring Hook

2 2 2 2 2 2 2 2 2

h.

Hollow Wall anchors

6 6 6 6 6 6 6 6 6

2 2 2 2 2 2 2 2

8 8 8 8 8 8 8 8

E

D

D

A

A

B

BCC

E

F

Item Parts List 100H 110H 120H 135H 150H 103C 125C 138C 158C

b.
c.

e.

f.

g.

i.
j.

k.

l.

m.

V071116-ESA www.elitescreens.com U-00017 2

Elbow Joints (2) 8 8 8 8 8 8 8 8 8

M4x6 Screws 60 60 60 60 60 60 60 60 60

Spring 92 96 104 116 128 88 104 116 134

Top wall brackets 2 2 2 2 2 2 2 2 2

Φ5x50 Wall Screws 6 6 6 6 6 6 6 6 6

Bottom wall brackets 2

Angle cover 4 4 4 4 4 4 4 4 4

M4x7 Screws 8

Center Support Bar 1 1 1 1 1 1 1 1 1

White glove s 2 2 2 2 2 2 2 2 2

Frame Assembly

Step 1: Place thesoft padded EPE sponge on clean area on the ground where the screen will be assembled.
Step 2: Position the pieces of the frame on the EPE sponge in the arrangement shown below

Step 3: Remove the tape on all frame ends before assembling the frame.

Step 4: Insert the center joint (a) connectors into one-half of the horizontal frame (b/c) and secure with the
M4x6 screws (c).

Step 5: Insert the springs (e) into the grooves of the frame. The spring’s hooks should be facing the front

side of the frame. For the correct amount of springs to place into the frame, please refer to the table listed
below.

Note: The springs are pre-installed into the grooves of the frame.

Screen Size

Spring

Qty

V071116-ESA www.elitescreens.com U-00017 3

A

B

100H 110H 120H 135H 150H 103C 125C 138C 158C

29 31 33 37 41 31 37 41 47

17 17 19 21 23 13 15 17 20

Step 6: Connect the elbow joints (b) to the top and bottom sections of the vertical frame. Once inserted,

Back side

Back Side

connect the vertical sections of the horizontal frame sections. Make sure all holes are in alignment and the
frame pieces are flush (no gaps). They should form perfect right angles.

Step 7: Secure the elbow joints by fastening them with M4x6 screws (c), 4 at each corner.

Screen Material

Step 8: Put on the white gloves (m) and carefully unro ll th e sc r een m ate rial on a clean surface from the

roller to the other side as shown below. The back side of the screen material should be placed upwards.

Step 9:Carefully and gently place the assembled frame on top of the screen material. Make sure to not allow
the angle edge of the frame to come in direct contact with the screen material to avoid puncturing it.

V071116-ESA www.elitescreens.com U-00017 4

Step 10: With one end of the spring and secure inside the groove of the frame, use the spring hook (d) to

1

1

2

2 3 3

1

1

Yellow label

attach the spring to the hole located on the screen material’s outer edge in the following order.

Attach the four corners first (1). After those are secure, connect the vertical portions of the material, begin in
the center and move towards the corners (2). Lastly, connect the horizontal sections of the material by
connecting the center of the material and make your way towards the corners (3).

Note (after all springs have been attached):
Correct material installation –Corners of the screen m ateria l are properly wrapped around the corner

edges of the frame and material is evenly tensioned and flat, creating a nicely taut surface.
Incorrect material installation –Thecorners of the screen material are not properly wrapped along the edge
of the frame leaving the material with unbalanced tension and an uneven finish. To correct, detach springs
from material at the corner(s) where material does not lie flat along the edge of the frame, reposition the
material so that it lies flat and wraps along the edge of the frame, and reattach springs to the material.

Note:Please make note of the yellow label and spring in the center of the frame. This is an indicator to start
the screen material installation process from the middle area of the frame.

Yellow spring

To avoid ripples forming in the material it is imperative that all of the corners are properly wrapped around the edges as illustrated in the check mark diagrams.

Center Support Bar

Step 11: Insert the Center Support Bar (i) into the upper top groove on the back of the frame with the

bottom end near the approximate center point of the frame and rotate it in at an angle so that both ends of
the bar are in alignment with the groove.

V071116-ESA www.elitescreens.com U-00017 5

Diagonal Models 150” an d below use 1 x Center Support Bar

Diagonal Models above 150” require 2 x Center Support Bars

Attention: Do not proceed with the Edge Trim installation until mak ing sure there
are no ripples in the mat erial.

Edge Trim Installation

Step 12: Place the Edge Trim over each end of the frame and secure with M4x6screws (c). Start with the center points first, then the rest of the corners as shown below.

Step 13: Install the angle cover (j) on each corn er of the frame and install the M4x7 screws to hold down

the angle cover.

V071116-ESA www.elitescreens.com U-00017 6

Notice to Installer:

Please use the following installation instructions to obtain superior optical performance from
the CineGrey 3D Angular Reflective ALR (Ambient Light Rejecting) Screen.

Make sure to follow these instructions in order for the CineGrey 3D to perform correctly.

•Angular-Reflective material is not compatible with ultra/short-throw projectors

•Minimum lens throw ratio 1.5x image width

•Ambient light must not come from the same direction as the projector

Since angular-reflective means that the projected image will reflect at the mirror­opposite angle, it is important to position the projector so that the viewer will get the best
possible image.

Step 1: Establish the general “eye level” of the viewers

Step 2: Set the appropriate projection level

Step 3: Adjust the screen height level and projection angle

Input Angle (A) = Output Angle (B) aligns with the viewer’s angle

V071116-ESA www.elitescreens.com U-00017 7

Wall Installat ion

Step 14: Measure the overall length and height of the frame and drill holes for the top brackets. Line up the

wall brackets with the drilled holes on the installation location and screw them in using a Phillips
screwdriver. If not installing into a structural wood stud, use a hollow wall anchor then screw in the M5x50
wood screws with a screwdriver. Make sure the brackets are leveled.

Step 15: Position the fixed frame screen onto the top wall brackets as shown below and push down at the
center of the top of the frame tosecure.

Step 16: With the frame slightly tilted outward; connect the bottom brackets onto the bottom groove of the
frame. Then secure them by screwing onto the wall

For Technical Support or an Elite Screens contact in your area, visit

www.elitescreens.com

V071116-ESA www.elitescreens.com U-00017 8