Manual Pull-down screen with a dual case design for wall or ceiling installation
Pre-Installation
1. Carefully unpack the screen.
2. Always handle the screen in a leveled position on a clean surface.
3. In order to protect the screen from exposure to stains, keep the screen out of contact with foreign
objects such as dust, saw dust, and/or liquids.
Note: Regardless of the mounting method, the screen should be securely supported so that
when retracted, deployed, or even abusive pulling on the screen, the case will not become loose
or fall. The installer must insure that the fasteners used are of adequate strength and suitable for
the installation location.
v.1 2
www.elitescreens.com
info@elitescreens.com
Page 2
Installation
Flush Mount to the Wall
1. Mark the location of where the screen is to be installed and drill your holes.
2. Insert the proper screw and leave about 1/8” of an inch from the wall to mount the screen.
3. Mount your screen from the keyhole located on back of the screen’s left and right end cap.
Back of end cap
Front view
(
Hardware not included
)
Side view
Suspended Ceiling using Chains
You can also hang the screen on a ceiling by using a chain (not included) and hang it by the two loops
(models 71‐120) located on each end of the case or by the ears of the end caps (models 135‐170).
71"-120"135"-170"
(
Hardware not included
Loops
)
Hole
- 2 -www.elitescreens.cominfo@elitescreens.com
Page 3
Screen Operation & Maintenance
Note:Always pull the screen down or retract in a 90‐degree vertical angle. To avoid damaging the
viewing surface, do not allow the viewing material to touch the screen case when deploying or
retracting the unit.
1. Pull the screen down from the lanyard or from the handle only in a 90‐degree angle. Do not attempt to
pull the screen down by the surface, as it will damage the screen and void the warranty.
2. To retract the screen back into its case, simply pull the screen down more than 2 inches and let the
screen retract by quickly and gently releasing it up.
Note: The interval auto‐lock mechanism system will cause the screen to stop and lock on the position
at intervals.
Note: Always release the screen at a 90‐degree angle and do not let go until the screen is entirely
inside the case. Keep in mind the screen’s mechanism is new and needs to be deployed/retracted a
few times to loosen up. If the screen feels stuck, carefully, with a little force, yank the screen straight
down to unlock the unit.
Note: Improper pulling on the screen to deploy/retract will damage material and/or the rolling system.
Maintenance
To clean the viewing material, use a soft cloth with mild soap and water. In order to keep the viewing surface
clean, it is recommended to keep the screen retracted into its housing case when not in use.
- 3 -www.elitescreens.cominfo@elitescreens.com
Page 4
Dimension Table
Screen Diag. Case Screen View Weight Bottom Screen Material View Overall End Cap End Cap Distance from
Model & Length Width Width Bar Edge to Weight Bar Height Height Height Width Screen material
Aspect Ratio (A) (A1) (A2) Length (A3) Distance (B4) Height (B3) (B1) (B) (B5) (C) to wall (C1)
Screen Diag. Case Screen View Weight Bottom Screen Material View Overall End Cap End Cap Distance from
Model & Length Width Width Bar Edge to Weight Bar Height Height Height Width Screen material
Aspect Ratio (A) (A1) (A2) Length (A3) Distance (B4) Height (B3) (B1) (B) (B5) (C) to wall (C1)
The listed measurements are for general reference only. Please contact Elite Screens to verify product design and dimensions before attempting to integrate its products with any structural or furniture modification.
Although a manufacturer may offer product advice, it may be taken or disregarded at the integrator’s discretion. Elite Screens will not be held responsible or be otherwise liable for faulty installations.
C
92
79.5
15
Unit:mm
11
10
Ø5
Ø10.5
20.5
A
A1
B1
B
B3
B5
A2
B4
C1
A3
- 4 -www.elitescreens.cominfo@elitescreens.com
Page 5
Warranty Policy
• Two (2) Year parts and labor warranty from defects in workmanship from purchase date as follows
(except for refurbished units as specified below).
• Three (3) Year parts and labor warranty from defects in workmanship for GEMR (Government,
Educational, Military, & Religious) purchases of new product only.
• Refurbished Units carry a 90‐DAY parts and labor warranty.
• Each party will be responsible for one way shipping during the warranty period.
• A RMA (Return Merchandise Authorization) number must be issued in order to process a replacement
or to authorize a return for warranty repair. Elite Screens will, at its sole option replace or repair the
defective unit with a replacement *(see exceptions below) after the defective unit or parts have been
received. Once the product is received, Elite Screens will send out a replacement *unit to the customer
by ground service (subject to inventory availability).
• Do Not Return Any Unauthorized Items to Elite Screens, as they will be refused and returned at your
expense. The RMA Number must be included on the outside label of your shipping box. Our warehouse
is not authorized to accept returns without an RMA number on the shipping label.
• RMA Numbers are valid for 45 days from the date issued.
• Missing Parts must be reported within 7 days of receipt. If reported after 7 days, the customer will be
responsible for shipping and handling fees. If reported after 30 days of receipt, the customer will be
responsible for cost of parts and shipping & handling fees.
* A New or refurbished replacement will be send out to the customer depending on the type of purchase
(new or refurbished) and based on stock availability.
North America only U.S. and Canada
For Warranty and Service requests, please submit an RMA/Service Form at:
www.elitescreens.com/warrantysupportform
Please visit this link for full Warranty information:
www.elitescreens.com/warranty
For Customer Service and Technical questions, please contact Elite Screens at:
Telephone: (877) 511‐1211 service@elitescreens.com
Fax: (562) 926‐8433 techsupport@elitescreens.com
Register your product at:
www.elitescreens.com
- 5 -www.elitescreens.cominfo@elitescreens.com
Page 6
Contact Information
US & Canada Tech Support & Warranty Claim
Please contact us at service@elitescreens.com or call +1 877.511.1211 #3 or fax +1.562.926.8433
Europe Tech Support & Warranty Claim
Please contact us at service@elitescreens.eu or call +49 (0) 40.30392958
Asia Tech Support & Warranty Claim
Please contact us at service@elitescreens.com.cn or call +86 (0) 755.8461.7989
Taiwan Tech Support & Warranty Claim
Please contact us at service@elitescreens.com.tw or call +866.2.8990.1999
Elite Screens America
16410 Manning Way | Cerritos | California 90703
www.elitescreens.com | info@elitescreens.com
Tel: 877.511.1211 | Fax: 1.562.926.8433
ASIA:
Elite Screens China Corp.
Longxi Duimianling Industry Zone
Longcheng Longgang District,
ShenZhen GuangDong, China
www.elitescreens.com.cn
info@elitescreens.com.cn
Tel: +86 (0) 755.8461.7989
Fax: +86 (0) 755.8461.7669
Elite Screens Taiwan Ltd.
1F. No. 38 Alley 22 Lane 66 Sec. 5
Nanjing E. Rd. Songshan District
Taipei City 105, Taiwan (R.O.C.)
www.elitescreens.com.tw
info@elitescreens.com.tw
Tel: 886 (0) 2.2747.8979
Elite Screens Japan Corp.
467-2-606 Tsuruma, Machida-shi,
Tokyo, 194-0004 Japan
www.elitescreens.jp
info@elitescreens.jp
Tel: 0120-07-0008
Fax: +81 (0) 42.706.9130