ELITEGROUP COMPUTER SYSTEMS TC7A W User Manual
User Manual
7” Multi Function Pad
mPAD2-7-CHT4-I
Issue Date: 2017.03.22 v1.0
Copyright
The documentation and the software included with this product are copyrighted 2009 by
ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd. All rights are reserved. ECS Co., Ltd.
reserves the right to make improvements in the products described in this manual at any time
without notice. No part of this manual may be reproduced, copied, translated or transmitted in
any form or by any means without the prior written permission of ECS Co., Ltd. Information
provided in this manual is intended to be accurate and reliable. However, ECS Co., Ltd.
assumes no responsibility for its use, nor for any infringements of the rights of third parties,
which may result from its use.
Acknowledgements
Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.
Declaration of Conformity
FCC Class B
Note: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/TV technician for help.
FCC Label Compliance Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Part No. 2014050100 Edition 1
Printed in China May 2014
mPAD2-7-CHT4-I Tablet PC User Manual ii
Caution! Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by the
manufacturer.
Dispose of used batteries according to the manufacturer's
instructions
Warning! Any changes or modifications made to the equipment which are not
expressly approved by the relevant standards authority could void your
authority to operate the equipment.
Attention! Toute modification apportée à l'équipement qui n'est pas expressément
approuvé par l'autorité des normes pertinentes peuvent annuler votre
droit à faire fonctionner l'équipement.
Attention!
Danger d'explosion si la pile est remplacée de façon incorrecte.
Remplacez-la uniquement avec le même type ou équivalent recommandé par le fabricant.
Jetez les piles usagées selon les instructions du fabricant
RF Exposure Information (SAR) This device meets the government's requirements for exposure to radio
waves. This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications Commission of
the U.S. Government. The exposure standard employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR
are conducted using standard operating positions accepted by the FCC with the EUT
transmitting at the specified power level in different channels. The FCC has granted an
Equipment Authorization for this device with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR information on this device is on file
with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid
after searching on FCC ID: WL6TC7A-W
iii mPAD2-7-CHT4-I Tablet PC User Manual
Warning!
To prevent electric shock, Do not remove cover.
No user serviceable parts inside, refer servicing to qualified personnel.
Additional Information and Assistance
1. Visit the ECS websites at www.ecs.com.tw where you can find the latest information
about the product.
2. Contact your distributor, sales representative, or ECS's customer service center for
technical support if you need additional assistance. Please have the following
information ready before you call:
- Product name and serial number
- Description of your peripheral attachments
- Description of your software (operating system, version, application software, etc.)
- A complete description of the problem
- The exact wording of any error messages
- This equipment is a source of electromagnetic waves. Before use, please make
sure that there are not EMI sensitive devices in its surrounding which may
- Warning!
- 1. Input voltage rated 100–240Vac, 50-60 Hz, 1.0 – 0.5 A, Output Voltage
- rated 12Vdc / 3A
- 2.Use a 3.7V, 4100mAh Lithium0ion battery (Model No. MICA-071)
3. Maintenance: to properly maintain and clean the surfaces,
use only approved products or clean with a dry applicator
iv mPAD2-7-CHT4-I Tablet PC User Manual
Attention! Pour éviter un choc électrique, ne pas retirer le couvercle.
Aucune pièce réparable par l'utilisateur, voir l'entretien à du personnel
qualifié.
- Attention!
1. Tension de sortie Tension d'entrée nominale 100–240Vac, 50-60 Hz, 1.0
– 0.5 A, la note de 12Vdc / 3A
2.Utiliser un V @ 4100 mA Batterie Lithium-ion (modèle n ° LWN436789) 3.7
3. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des
produits approuvés ou nettoyer avec un applicateur sec
Packing List
Before setting up the system, check that the items listed below are included and in good
condition. If any items are missing, please contact your dealer immediately.
mPAD2-7-CHT4-I Pad x1
Strap x1
DC Charge Cable x1
HDMI Docking cable x1
USB3.0 Docking cable x1
Docking x1
MSR Module x1
SCR Module x1
Barcode scanner Module x1
USB Ethernet Module x1
v mPAD2-7-CHT4-I Tablet PC User Manual
Caution!
This adapter Asian Power Devices Inc Type: WA-36A12RU-AAAG is a forming part of
the medical device.
IE IEC 60417 – 5009 : STAND-BY
IEC 60417 – 5031 : Direct Current
IEC 60417-5172 : ClassⅡequipment
Operation Instructions
Safety Instructions
Your system is designed and tested to meet the latest standards of safety for information technology
equipment. However, to ensure your safety, it is important that you read the following safety
instructions.
Setting up your system
• Read and follow all instructions in the documentation before you operate your system.
• Do not use this product near water or a heated source such as a radiator.
• Set up the system on a stable surface.
• Use this product in environments with ambient temperatures between 0°C and 35°C.
Attention during use
• Do not step on the power cord or let anything rest on top of it.
• Do not spill water or any other liquid on your system.
• When the system is turned OFF, a small amount of electrical current still flows. Always unplug all
power, modem, and network cables from the power outlets before cleaning the system.
• If you encounter the following technical problems with the product, unplug the power cord and contact
a qualified service technician or your retailer.
• The power cord or plug is damaged.
• Liquid has been spilled into the system.
• The system does not function properly even if you follow the operating instructions.
• The system was dropped or the cabinet is damaged.
• The system performance changes
Intend use
The equipment is intended for infant or adults by profession Health care professionals.
Mobile electronic medical records (EMR)
Move the image library
Mobile rounds
Move the drug
Mobile registration branch
vi mPAD2-7-CHT4-I Tablet PC User Manual
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User Manual for later reference.
3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth. Do not
use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near the equipment and must
be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall may
cause damage.
7. The openings on the enclosure are for air convection. Protect the equipment from
overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to
the power outlet.
9. Position the power cord so that people cannot step on it. Do not place anything over the power
cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the power source to avoid
damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should be opened only by
qualified service personnel.
14. If one of the following situations arises, get the equipment checked by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the user's
manual.
e. The equipment has been dropped and damaged. f. The
equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE
TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60°C (140° F). THIS COULD
DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A CONTROLLED
ENVIRONMENT.
16. If your computer is losing time significantly or the BIOS configuration resets itself to the
default, the battery may have no power.
17. CLASSIFICATION: Supply Class II adapter
(EDAC, EM1024PR)
No applied part
Continuous Operation
Not AP or APG category
18.Disconnect device: Removed the supply plug of direct plug–in adapter from the wall.
19.Follow national, state or local requirements to dispose of unit.
20.Maintenance: to properly maintain and clean the surfaces, use only the approved products or clean with a
dry applicator.
21.Contact information:
No.239, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.).
TEL: +886 2-2162-1177
22.This equipment shall not be used as a life support system.
23. Accessory equipment connected to the analog and digital interfaces must be in compliance with the
respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.) Furthermore all configurations
shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part or signal output part is
configuring a medical system, and is therefore, responsible that the system complies with the requirements of
the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified equipment in the patient
environment and IEC 60XXX certified equipment out- side of the patient environment. If in doubt, consult the
technical services department or your local representative.
24.Users must not allow SIP/SOPs to come into contact with the patient at the same time.
25.The sound pressure level at the operator's position according to IEC 704-1:1982
is no more than 70dB (A).
DISCLAIMER: This set of instructions is given according to IEC 704-1. ECS disclaims all responsibility for the
accuracy of any statements contained herein.
26. Turning off 7” multi function Pad, mPAD2-7-CHT4-M properly is important for system reliability.
There are two ways to turn off the system.
1. On the start menu, click “Shut down” and select “OK”
2. Push the power button and then the system will shut down automatically
mPAD2-7-CHT4-I Tablet PC User Manual vii
1. Do not replace battery yourself. Please contact a qualified technician or your retail
provider.
Caution! 2 .The computer is provided with a battery-powered real-time clock circuit. There is a
danger recommended by the manufacturer. Discard used batteries according to the
manufacturer's instructions.
1. Ne pas remplacer la batterie vous-même. S'il vous plaît contacter un technicien qualifié
Attention! ouvotre fournisseur de détail.
2. L'ordinateur est muni d'un circuit en temps réel de l'horloge alimentée par batterie. Il ya
un danger d'explosion si la pile est remplacée de façon incorrecte. Remplacez
uniquement par un type identique ou équivalent recommandé par le fabricant. Jetez les
piles usagées selon les instructions du fabricant.
27. Product disposal notice
INPORTANT:
This symbol if the crossed out wheeled bin indicates that the product (electrical and
electronic equipment) should not be placed in municipal waste. Check local
regulations for disposal of electronic products.
28. mPAD2-7-CHT4 product service life is 3 Years.
29. The expected service life of the battery pack is expected to be approximately 3000 cycles.
This device has no shelf life, however the battery contained within has, therefore the device shall
be charged to full battery volume at least once every 6 months.
30. Do not modify this equipment without authorization of the manufacturer
31. The separable plug is used as isolation means, the device do not be positioned so that it is
difficult to disconnect device.
32. If power supply cord is optional in CCL, then need some statement in manual indicating user to
use suitable supply cord, ex medical grade and reliable grounding?
1. Grounding reliability can only be achieved when the equipment is connected to an
equivalent receptacle marked" Hospital Only" or "Hospital Grade".
2. Use a power cord that matches the voltage of the power outlet, which has been approved and
complied with the safety standard of your particular country.
33. Contact information:
ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd.
No.239, Sec. 2, Tiding Blvd., Neihu District, Taipei City 11493, Taiwan (R.O.C.).
TEL: +886 2-2162-1177
FAX: +886 2-2797-0690
http://www.ecs.com.tw
mPAD-7-CHT4-I Tablet PC User Manual viii
Contents
Chapter 1 General Information ............................1
1.1 Introduction .............................................................................................. 2
1.2 Medical Application....................................................................................2
1.3 Specifications .......................................................................................... 2
Tab l e 1 . 1 : m P A D 2 - 7 - CHT4 - I S p e c if ic at i o n . . . . . 2
1.4 Cleaning/Disinfecting ............................................................................... 4
1.5 Dimensions .............................................................................................. 5
Figure 1.1 mPAD2-7-CHT4-I Dimensions ............... 6
Chapter 2 Getting Started.....................................7
2.1 A Qu ic k T ou r o f m PA D2 -7-CHT4 -I .. .. ....... .. .. .. .. ..... 8
Figure 2.1 Front View ............................................................... 8
Figure 2.2 Left Side View........................................................... 8
Figure 2.3 Right Side View ....................................................... 9
Figure 2.4 Rear View ................................................................... 9
Figure 2.5 Top View ……........................................................... 10
2.2 A Quick Tour of mPAD2-7-CHT4-I Docking Station (Optional)............... 10
Figure 2.6 Rear View of Docking Station ..................................10
Figure 2.7 Strap ........................................................................ 10
2.3 Insert the USB Module into the mPAD2-7-CHT4 TABLET (Optional)…...... 11
2.4 Installation Procedures........................................................................... 12
2.4.1 Install the Strap (Optional).......................................................... 12
Figure 2.8 Install the Strap......................................................... 12
2.4.2 Insert / Hang the Stylus (Optional)............................................. 12
Figure 2.9 Stylus...................................................................... 12
Figure 2.10 Secure the stylus.................................................... 12
2.4.3 Insert the mPAD2-7-CHT4-I into the Docking Station (Optional) 13
Figure 2.11 Open and secure the protective cover.................... 13
Figure 2.12 mPAD2-7-CHT4-I in Docking Station.................. 13
2.4.4 Connecting the Power Cord for the Docking Station.................. 14
Figure 2.13 Connecting the AC Adapter Power Supplier to the
Docking Station………………………………………………....... 14
2.4.5 Warning information for table use. .................. 14
Figure 2.14 when table put into Dock...............................................15
Vi mPAD-7-CHT3-I Tablet PC User Manual
Chapter 3 EMC TEST
REPORT.................................16
3.1 Description of Standards and Results for EN55022/EN5502.......... 17
Chapter 4
Troubleshooting.................................18
4.1 Solving Problems ...................... ......... ...................... ...................... 19
4.2 Troubleshooting Display Problems Solving Problems ...................... 19
4.3 Troubleshooting Audio Problems ........................................ 20
4.4 Clean tips ........................................ 20
Loading...