ELITEGROUP COMPUTER SYSTEMS TB71A W SI2 User Manual

User Manual

7” Multi Function Pad

mPAD-7-CHT3-I

y

Copyright

The documentation and the software included with this product are copyrighted 2009 by
ECS(ELITEGROUP COMPUTER SYSTEM) Co., Ltd. All rights are reserved. ECS Co.,
Ltd. reserves the right to make improvements in the products described in this manual at
any time without notice. No part of this manual may be reproduced, copied, translated or
transmitted in any form or by any means without the prior written permission of ECS Co.,
Ltd. Information provided in this manual is intended to be accurate and reliable. However,
ECS Co., Ltd. assumes no responsibility for its use, nor for any infringements of the rights
of third parties, which may result from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.

Declaration of Conformit

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

 Reorient or relocate the receiving antenna.

 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

FCC Label Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

mPAD-7-CHT3-I Tablet PC User Manual

Part No. 2014050100 Edition 1

Printed in China May 2014

ii

A

A

Warning! Any changes or modifications made to the equipment which are not

expressly approved by the relevant standards a uthority could void your
authority to operate the equipment.

ttention! Toutemodification apportéeàl'équipement quin'estpasexpressément

approuvé par l'autorité des normes pertinentes peuvent annuler votre
droit à faire fonctionner l'équipement.

Caution! Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the
manufacturer.
instructions

Dispose of used batteries according to the manufacturer's

ttention!

RF Exposure Information (SAR) This device meets the government's requirements for exposure to radio

Danger d'explosion si la pile est remplacée de façon incorrecte.
Remplacez-la uniquement avec le même type ou équivalent recommandé par le fabricant.
Jetez les piles usagées selon le s instructions du fabricant

waves. This device is designed and manufactured not to exceed the emission limits for
exposure to radio frequency (RF) energy set by the Federal Communications Commission of
the U.S. Government. The exposure standard employs a unit of measurement known as the
Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg. Tests for SAR
are conducted using standard operating positions accepted by the FCC with the EUT
transmitting at the specified power level in different channels. The FCC has granted an
Equipment Authorization for this device with all reported SAR levels evaluated as in
compliance with the FCC RF exposure guidelines. SAR information on this device is on file
with the FCC and can be found under the Display Grant section of www.fcc.gov/eot/ea/fccid
after searching on FCC ID: WL6TB71A-W-SI2

g

!

r

A

Packing List

Before setting up the system, check that the items listed below are included and in good
condition. If any items are missing, please contact your dealer immediately.

 mPAD-7-CHT3-I Pad x1

 Strap x1

 Stylus pen x1

 HDMI Docking cable x1

 USB3.0 Docking cable x1

 Docking Holder x1

 Docking Power adapter x1

 Software CD (Drivers and Utility, Manual)

Warnin

ttention! Pour éviter un choc électrique, ne pas retirer le couvercle.

To prevent electric shock, Do not remove cover.

No user serviceable parts inside, refer servicing to qualified pe rsonnel.

Aucune pièce réparable par l'utilisateur, voir l'entretien à du personnel
qualifié.

Additional Information and Assistance

1. Visit the ECS websites at www.ecs.com.tw where you can find the latest information

about the product.

2. Contact your distributor, sales representative, or ECS's customer service center for

technical support if you need additional assistance. Please have the following
information ready before you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, application software, etc.)

- A complete description of the problem

- The exact wording of any error messages

- This equipment is a source of electromagnetic waves. Before use, please make

sure that there are not EMI sensitive devices in its surrounding which may
malfunction therefore

-

Warning!

-

1. EDAC Power Electronics Co., Ltd./ EA1024CR-050 Input voltage rated:

- 100-240Vac, 50-60Hz, 1.0A, Output voltage rated: 5Vdc, 4A

2.Use a 3.7V, 4100mAh Lithium0ion battery (Model No. MICA-071)

3. Maintenance: to properly maintain and clean the surfaces,

use only approved products or clean with a dry applicator

- Attention!

1. Utiliser un V @ 4100 mA Batterie Lithium-ion (modèle n ° LWN436789) 3.7

2. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des

produits approuvés ou nettoyer avec un applicateur sec

3. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des

produits approuvés ou nettoyer avec un applicateur sec

iii mPAD-7-CHT3-I Tablet PC Use

!

A

r

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.

Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment

and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall

may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything over

the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to

avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:

a. The power cord or plug is damaged.

b. Liquid has penetrated into the equipment.

c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the

user's manual.

e. The equipment has been dropped and damaged. f.

The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE

TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60°C (140° F). THIS
COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.

16. If your computer is losing time significantly or the BIOS configuration resets itself

to the default, the battery may have no power.

Caution

1. Ne pas remplacer la batterie vous-même. S'il vous plaît contacter un

mPAD-7-CHT3-I Tablet PC User Manual iv

 1. Do not replace battery yourself. Please contact a qualified technician or

your retail provider.

2. The computer is provided with a battery-powered real-time clock circuit.
There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.

ttention!

technicien qualifié ou votre fournisseur de détail.

2. L'ordinateur est muni d'un circuit en temps réel de l'horloge alimentée pa
batterie. Il ya un danger d'explosion si la pile est remplacée de façon
incorrecte. Remplacez uniquement par un type identique ou équivalent
recommandé par le fabricant. Jetez les piles usagées selon les instructions
du fabricant.

17. IMPROPER INSTALLATION OF VESA MOUNTING CAN RESULT IN SERIOUS

PERSONAL INJURY! VESA mount installation should be performed by a professional
technician; please contact the service technician or your retailer if you need this
service.

18. CLASSIFICATION:

Supply Class I adapter
No applied part

IP54
Continuous Operation
Not AP or APG category

19. Disconnect device: Appliance inlet.

20. Follow national, state or local requirements to dispose of unit.

21. Maintenance: to properly maintain and clean the surfaces, use only the

approved products or clean with a dry applicator.

22. Contact information:

No.239, Sec. 2, Ti Ding Blvd., Taipei City 11493, Taiwan (R.O.C.)
TEL: [phone]

23. This equipment shall not be used as a life support system.

24. Accessory equipment connected to the analog and digital interfaces must be in

compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
Furthermore all configurations shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part or signal
output part is configuring a medical system, and is therefore, responsible that the
system complies with the requirements of the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60XXX certified equipment out- side of
the patient environment. If in doubt, consult the technical services department or your
local representative.

25. Users must not allow SIP/SOPs to come into contact with the patient at the same

time.

26. The sound pressure level at the operator's position according to IEC 704-1:1982

is no more than 70dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. ECS disclaims all
responsibility for the accuracy of any statements contained herein.

mPAD-7-CHT3-I Tablet PC User Manual

mPAD-7-CHT3-I Tablet PC User Manual vi

A

Contents

Chapter 1 General Information ............................1

1.1 Introduction .............................................................................................. 2

1.2 Specifications .......................................................................................... 2

Table 1.1:mPAD-7-CHT3-ISpecification..... 2

1.3 Cleaning/Disinfecting ............................................................................... 4

1.4 Dimensions .............................................................................................. 5

Figure 1.1 mPAD-7-CHT3-I Dimensions ............... 5

Chapter 2 Getting Started.....................................7

2.1

2.2 A Quick Tour of mPAD-7-CHT3-I Docking Station(Optional)................. 10

2.3 Installation Procedures........................................................................... 11

Quick Tour of mPAD-7-CHT3-I ........................ 8

Figure 2.1 Front View ............................................................... 8

Figure 2.2 Left Side View........................................................... 8

Figure 2.3 Right Side View ....................................................... 9

Figure 2.4 Rear View ................................................................... 9

Figure 2.5 Top View ……........................................................... 10

Figure 2.6 Front View ............................................................. 10

Figure 2.7 Rear View of Docking Station ...................................10

Figure 2.8 Strap ........................................................................ 11

2.3.1 Install the Strap (Optional).......................................................... 11

Figure 2.9 Install the Strap......................................................... 11

2.3.2 Insert / Hang the Stylus (Optional)............................................. 11

Figure 2.10 Stylus...................................................................... 11

Figure 2.11 Secure the stylus.................................................... 12

2.3.3 Insert the mPAD-7-CHT3-I into the Docking Station(Optional).. 12

Figure 2.12 Open and secure the protective cover.................... 12

Figure 2.13 mPAD-7-CHT3-I in Docking Station.................. 12

2.3.4 Connecting the Power Cord for the Docking Station.................. 13

Figure 2.14 Connecting the AC Adapter Power Supplier to the

Docking Station………………………………………………....... 13

2.3.5 Connecting the USB Charger to mPAD-7-CHT3-I............ 14

Figure 2.15 Connecting the AC Adapter Power Supplier to the

Docking Station……………………………………………............ 14

Vi mPAD-7-CHT3-I Tablet PC User

mPAD-7-CHT3-I Tablet PC User Manual

Chapter 1

1 General Information

,

,

.

g

pset

p

p

A

1.1 Introduction

mPAD-7-CHT3-I is a multimedia Atom Mobile processor-based computer. It is a PC-based
system with 7" TFT LCD display and a stereo audio controller. mPAD-7-CHT3-I is a simple,
complete and highly integrated mobile multimedia system which allows system integrators to
easily build a Mobile Clinical Assistant Terminal into their applications.

Common industrial applications include factory automation systems, precision machinery
and production process control. It is also suitable for many non-industrial applications
including interactive kiosk systems, entertainment management, and car park automation
mPAD-7-CHT3-I is a reliable, cost-effective solution to meet an application’s processin
requirements.

1.2 Specifications

Table 1.1: mPAD-7-CHT3-I
Specification

Item Description

Dimensions (WþDþH) 121 mm x 200 mm x 14.5 / 24 mm (bottom / top)

Weight 400g
CPU and Chi

Memory DDR3L 1600MHz

Graphics

Audio

I/O Ports

- Quad core (4C/4T), SoC

-2M Cache, u

®

Intel

Integrated HD Graphics

to 1.84 GHz

Realtek ALC5645

Internal Speaker x1, internal microphone x 2

Docking port x 1
SD card slot x 1

Line out x 1

Display 7" TFT LCD Panel

Touch Panel 10-point P-cap touch panel

Max. Resolution 1920 x 1200

Stylus Pen Capacitive stylus pen

Storage

Communication

Ingress Protection IP54-rated, Alcohol resistant for cleaning purposes

Thermal Solution Fanless Design

erating System

O

Barcode Scanner 1D/2D Barcode scanner

Camera 5.0 Mega pixel camera with LED light

mPAD-7-CHT3-I Tablet PC User Manual

EMMC 32G

WiFi- 802.11 b/g/n WLAN (2.4 G)
Bluetooth V2.0+EDR / Bluetooth 4.0 LE

NFC ISO14443 TypeA, Type B, PC/SC

Windows 10 Industry Pro 64Bits

uto-focus supported

Web Camera 2.0 Mega pixel VGA camera

Power button: On the top side of mPAD-7-CHT3-I
Barcode scanner buttons: Two orange buttons

Control Button

Indicated LED

Power Adapter

Volume control button

Home Key button

Programmable button (Default setting):

- P1 for S3 mode

- P2 for WiFi on/off

Power LED & Battery status LED

 Full → Blue
 Charging → Orange

EDAC EA1024CR-050
Input voltage rated: 100-240Vac, 50-60Hz, 1.0A
Output voltage rated: 5Vdc, 4A
4 Hr charging time

Battery

Operating Temperature 0° C ~ 40° C

Operating Humidity 90% @ 40° C, non-condensing

Storage Temperature -20° C ~ 65° C

Storage Humidity 95%, non-condensing

Transportation Temperature -20° C ~ 65° C Transportation

Humidity 95%, non-condensing

Certifications

Safety

FCC Part 15 Class B, UL, CE, CB60950, RoHS, WEEE
(Documents ready only)

3 mPAD-7-CHT3-I Tablet PC User

y

A

1.3 Cleaning/Disinfecting

- During normal use mPAD-7-CHT3-I may become soiled and should, therefore,
be cleaned regularly. Steps:

1. Wipe mPAD-7-CHT3-I with a clean cloth that has been moistened in the cleaning solution.

2. Prepare agent per manufacturer’s instructions or hospital protocol.

3. Wipe thoroughly with a clean cloth.

Caution! Do not immerse or rinse mPAD-7-CHT3-I or its peripheral s. If you accidentall

spill liquid on the device, disconnect the unit from the power source. Contact
your Biomed personnel regarding the continued safety of the unit before
placing it back in operation.

Do not spray cleaning agent on the chassis.
Do not use disinfectants that contain phenol.
Do not autoclave or clean mPAD-7-CHT3-I or its peripherals with strong

aromatic, chlorinated, ketone, ether, or other solvents, sharp tools or
abrasives. Never immerse electrical connectors in water or othe r liquids.

ttention! Ne pas immerger ou rincer mPAD-7-CHT3-I ou ses périphériques. Si vous

renversez par accident un liquide sur l'appareil, débranchez l'appareil de la
source d'alimentation. Contactez votre Biomed concernant la sé curité
continue de l'unité avant de la remettre en service.
Ne pas pulvériser l'agent de nettoyage sur le châssis.
Ne pas utiliser de désinfectants contenant du phénol.
Ne pas passer à l'autoclave ou mPAD-7-CHT3-I A propre ou ses
périphériques avec fortes, cétone, éther, ou d'autres solvants, des outils
tranchants ou abrasifs aromatiques chlorés. Ne jamais plonger connecteurs
électriques dans l'eau ou d'autres liquids.

mPAD-7-CHT3-I Tablet PC User Manual

1.4 Dimensions



121mm

200mm

Figure 1.1 mPAD-7-CHT3-I Dimensions

5 mPAD-7-CHT3-I Tablet PC User

Chapter 2

g

2 Gettin

Started

g

g

A

2.1 A Quick Tour of mPAD-7-CHT3-I






Before you start to set up mPAD-7-CHT3-I, take a moment to become familiar with the
locations and purposes of the controls, drives, connections and ports, which are illustrated in
the figures below.






When placed upright on the desktop, the mPAD-7-CHT3-I front panel appears as shown in
Figure 2.1.



LED indicator

mbient sensor

Camera





Home Key

Fi

ure 2.1 Front View

The volume control button, barcode scanner button and docking connector are on the left side
of the tablet PC.

Volume control button

Barcode scanner button

Docking connector

Hang hole

Fi

ure 2.2 Left Side View

mPAD-7-CHT3-I Tablet PC User Manual

The card slots, barcode scanner button and programmable buttons are on the right side of

g

the tablet PC.

Card Slots (Micro SD)

Barcode scanner button

Programmable key

Hang hole

Figure 2.3 Right Side View

The rear view of the tablet PC is depicted in Figure 2.4.

Camera

Speaker

Camera flash

Fi

ure 2.4 Rear View

9 mPAD-7-CHT3-I Tablet PC User

t

t

t

g

g

g

The top side of the tablet PC contains power button, barcode scanner and headphone jack.

ure 2.5 TopView

Fi

2.2 A Quick Tour of mPAD-7-CHT3-I Docking Holder

(Optional)

When you place the docking station on the desktop, its front panel appears as shown in Figure

2.6.

Docking connector

Fi

ure 2.6 Front View

USB 3.0

por

Fi

USB 2.0

ports

ure 2.7 Rear View of Docking Station

HDMI

por

LAN
por

DC in jack

mPAD-7-CHT3-I Tablet PC User Manual

g

2.3 Installation Procedures

2.3.1 Install the Strap (Optional)

This strap is designed for the mPAD-7-CHT3-I, which make the tablet convenient to hold.



Fi

ure 2.8 Strap

a. Aim the triangle mark on the strap to the home key to slightly insert the bottom side of the

tablet into the strap.

b. Press to insert the top side of tablet into the strap.

Figure 2.9 Install the Strap

2.3.2 Insert / Hang the Stylus (Optional)

Figure 2.10 Stylus

11 mPAD-7-CHT3-I Tablet PC User

r




a. Hang and secure the stylus through the hang hole of the mPAD-7-CHT3-I.

b. Insert and secure the stylus onto the strap.

 

e 2.11 Secure the stylus

Figu

2.3.3 Insert the mPAD-7-CHT3-I into the Docking Station (Optional)

2. Open and turn the protective cover of the docking port to the opposite side and press to
lock it into its reserved slot.

Figure 2.12 Open and secure the protective cover

1. Align the docking port to the docking connector to insert the tablet into the docking station
and press it right into position.

Figure 2.13 mPAD-7-CHT3-I in Docking Station

Note! Before placing the tablet into the docking station, please make sure that the

protective cover of docking port is placed right into its reserved slot.

mPAD-7-CHT3-I Tablet PC User Manual 12

g

2.3.4 Connecting the Power Cord for the Docking Station

Be sure to always handle the power cords by holding the plug ends only. Follow

these procedures in order:

1. Insert the mPAD-7-CHT3-I into the docking station as previous section 2.3.3.(See

Figure 2.13).

2. Connect the female end of the power cord to the DC-in jack of the docking station.

3. Connect the 2-pin male plug of the power cord to an electrical outlet.

Step 3 Step 2

ure 2.14 Connecting the AC Adapter Power Supplier to the Docking Station

Fi

13 mPAD-7-CHT3-I Tablet PC User Manual

,

-

www.ecs.com.tw

This guide is intended for reference purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means
electronic, photocopying, recording or otherwise, without prior written permis
sion of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© ELITEGROUP COMPUTER SYSTEM Co., Ltd. 2016