ELITEGROUP COMPUTER SYSTEMS TB71A-W User Manual

User Manual

MICA-071

7" Intel Atom based Pocketable
pads

Copyright

The documentation and the software included with this product are copyrighted 2009 by
Advantech Co., Ltd. All rights are reserved. Advantech Co., Ltd. reserves the right to make
improvements in the products described in this manual at any time without notice. No part
of this manual may be reproduced, copied, translated or transmitted in any form or by any
means without the prior written permission of Advantech Co., Ltd. Information provided in
this manual is intended to be accurate and reliable. However, Advantech Co., Ltd.
assumes no responsibility for its use, nor for any infringements of the rights of third parties,
which may result from its use.

Acknowledgements

Intel and Pentium are trademarks of Intel Corporation.
Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.
All other product names or trademarks are properties of their respective owners.

Declaration of Conformity

FCC Class B

Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:

 Reorient or relocate the receiving antenna.
 Increase the separation between the equipment and receiver.
 Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

 Consult the dealer or an experienced radio/TV technician for help.

Part No. 2014050100 Edition 1
Printed in China May 2014

MICA Tablet PC User Manual ii

FCC Label Compliance Statement:

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Caution! Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended by the
manufacturer.

Dispose of used batteries according to the manufacturer's

instructions

Warning! Any changes or modifications made to the equipment which are not

expressly approved by the relevant standards authority could void your
authority to operate the equipment.

Attention! Toute modification apportée à l'équipement qui n'est pas expressément

approuvé par l'autorité des normes pertinentes peuvent annuler votre
droit à faire fonctionner l'équipement.

Attention!

Danger d'explosion si la pile est remplacée de façon incorrecte.
Remplacez-la uniquement avec le même type ou équivalent recommandé
par le fabricant. Jetez les piles usagées selon les instructions du fabricant

Part No. 2014050100 Edition 1
Printed in China May 2014

MICA Tablet PC User Manual

Warning!

To prevent electric shock, Do not remove cover.

No user serviceable parts inside, refer servicing to qualified personnel.

Additional Information and Assistance

1. Visit the Advantech websites at www.advantech.com or www.advantech.com.tw where

you can find the latest information about the product.

2. Contact your distributor, sales representative, or Advantech's customer service center

for technical support if you need additional assistance. Please have the following
information ready before you call:

- Product name and serial number

- Description of your peripheral attachments

- Description of your software (operating system, version, application software, etc.)

- A complete description of the problem

- The exact wording of any error messages

- This equipment is a source of electromagnetic waves. Before use, please make

sure that there are not EMI sensitive devices in its surrounding which may
malfunction therefore

Warning! 1. Input voltage rated 100-240 VAC, 50-60 Hz, 1.5 A, Output

Voltage rated 5 VDC, 2 A

2. Use a 3.7 V @ 4100 mA Lithium-ion battery (Model No. LWN436789)

3. Maintenance: to properly maintain and clean the surfaces, use only

approved products or clean with a dry applicator

iii MICA Tablet PC User Manual

Attention! Pour éviter un choc électrique, ne pas retirer le couvercle.

Aucune pièce réparable par l'utilisateur, voir l'entretien à du personnel
qualifié.

Attention! 1. Tension de sortie Tension d'entrée nominale 100-240 VAC, 50-

60 Hz, 1,5 A, la note de 5 VDC, 2 A

2. Utiliser un V @ 4100 mA Batterie Lithium-ion (modèle n ° LWN436789) 3.7

3. Entretien: bien entretenir et nettoyer les surfaces, utiliser uniquement des

produits approuvés ou nettoyer avec un applicateur sec

Packing List

Before setting up the system, check that the items listed below are included and in good
condition. If any items are missing, please contact your dealer immediately.

 MICA-071 x1
 Strap x1
 Stylus pen x1
 USB Charger
 USB Charge Docking Cable x1
 HDMI Docking cable x1
 USB3.0 Docking cable x1
 Docking Holder x1
 Docking Power adapter x1
 Software CD (Drivers and Utility, Manual)

Safety Instructions

1. Read these safety instructions carefully.

2. Keep this User Manual for later reference.

3. Disconnect this equipment from any AC outlet before cleaning. Use a damp cloth.

Do not use liquid or spray detergents for cleaning.

4. For plug-in equipment, the power outlet socket must be located near the equipment

and must be easily accessible.

5. Keep this equipment away from humidity.

6. Put this equipment on a reliable surface during installation. Dropping it or letting it fall

may cause damage.

7. The openings on the enclosure are for air convection. Protect the equipment from

overheating. DO NOT COVER THE OPENINGS.

8. Make sure the voltage of the power source is correct before connecting the

equipment to the power outlet.

9. Position the power cord so that people cannot step on it. Do not place anything over

the power cord.

10. All cautions and warnings on the equipment should be noted.

11. If the equipment is not used for a long time, disconnect it from the power source to

avoid damage by transient overvoltage.

12. Never pour any liquid into an opening. This may cause fire or electrical shock.

13. Never open the equipment. For safety reasons, the equipment should be

opened only by qualified service personnel.

14. If one of the following situations arises, get the equipment checked by service

personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work according to the

user's manual.
e. The equipment has been dropped and damaged. f.
The equipment has obvious signs of breakage.

15. DO NOT LEAVE THIS EQUIPMENT IN AN ENVIRONMENT WHERE THE STORAGE

TEMPERATURE MAY GO BELOW -20° C (-4° F) OR ABOVE 60°C (140° F). THIS
COULD DAMAGE THE EQUIPMENT. THE EQUIPMENT SHOULD BE IN A
CONTROLLED ENVIRONMENT.

16. If your computer is losing time significantly or the BIOS configuration resets itself

to the default, the battery may have no power.

Caution! 1. Do not replace battery yourself. Please contact a qualified technician or

your retail provider.

2. The computer is provided with a battery-powered real-time clock circuit.

There is a danger of explosion if battery is incorrectly replaced. Replace
only with same or equivalent type recommended by the manufacturer.
Discard used batteries according to the manufacturer's instructions.

MICA Tablet PC User Manual iv

Attention! 1. Ne pas remplacer la batterie vous-même. S'il vous plaît contacter un

technicien qualifié ou votre fournisseur de détail.

2. L'ordinateur est muni d'un circuit en temps réel de l'horloge alimentée par
batterie. Il ya un danger d'explosion si la pile est remplacée de façon
incorrecte. Remplacez uniquement par un type identique ou équivalent
recommandé par le fabricant. Jetez les piles usagées selon les instructions
du fabricant.

17. IMPROPER INSTALLATION OF VESA MOUNTING CAN RESULT IN SERIOUS

PERSONAL INJURY! VESA mount installation should be performed by a professional
technician; please contact the service technician or your retailer if you need this
service.

18. CLASSIFICATION:

Supply Class I adapter
No applied part

IP54
Continuous Operation
Not AP or APG category

19. Disconnect device: Appliance inlet.

20. Follow national, state or local requirements to dispose of unit.

21. Maintenance: to properly maintain and clean the surfaces, use only the

approved products or clean with a dry applicator.

22. Contact information:

No.1, Alley 20, Lane 26, Rueiguang Road Neihu District, Taipei, Taiwan 114,
R.O.C.
TEL: [phone]

23. This equipment shall not be used as a life support system.

24. Accessory equipment connected to the analog and digital interfaces must be in

compliance with the respective nationally harmonized IEC standards (i.e. IEC
60950 for data processing equipment, IEC 60065 for video equipment, IEC
61010-1 for laboratory equipment, and IEC 60601-1 for medical equipment.)
Furthermore all configurations shall comply with the system standard IEC
60601-1-1. Anyone who connects additional equipment to the signal input part or signal
output part is configuring a medical system, and is therefore, responsible that the
system complies with the requirements of the system standard IEC
60601-1-1. The unit is for exclusive interconnection with IEC 60601-1 certified
equipment in the patient environment and IEC 60XXX certified equipment out- side of
the patient environment. If in doubt, consult the technical services department or your
local representative.

25. Users must not allow SIP/SOPs to come into contact with the patient at the same

time.

26. The sound pressure level at the operator's position according to IEC 704-1:1982

is no more than 70dB (A).

DISCLAIMER: This set of instructions is given according to IEC 704-1. Advantech disclaims
all responsibility for the accuracy of any statements contained herein.

v MICA Tablet PC User Manual

Contents

Chapter 1 General Information ............................1

1.1 Introduction .............................................................................................. 2

1.2 Specifications .......................................................................................... 2

Table 1.1: MICA Specification ................................................. 2

1.3 Cleaning/Disinfecting ............................................................................... 4

1.4 Dimensions .............................................................................................. 5

Figure 1.1 MICA Dimensions ....................................................... 5

Chapter 2 Getting Started.....................................7

2.1 A Quick Tour of MICA .............................................................................. 8

Figure 2.1 Front View .................................................................. 8

Figure 2.2 Left Side View............................................................. 8

Figure 2.3 Right Side View .......................................................... 9

Figure 2.4 Rear View ................................................................... 9

Figure 2.5 Top View ……........................................................... 10

2.2 A Quick Tour of MICA Docking Station (Optional) ................................. 10

Figure 2.6 Front View ................................................................ 10

Figure 2.7 Rear View of Docking Station ...................................10

Figure 2.8 Strap ........................................................................ 11

2.3 Installation Procedures........................................................................... 11

2.3.1 Install the Strap (Optional).......................................................... 11

Figure 2.9 Install the Strap......................................................... 11

2.3.2 Insert / Hang the Stylus (Optional)............................................. 11

Figure 2.10 Stylus...................................................................... 11

Figure 2.11 Secure the stylus.................................................... 12

2.3.3 Insert the MICA into the Docking Station (Optional)................... 12

Figure 2.12 Open and secure the protective cover.................... 12

Figure 2.13 MICA-071 in Docking Station.................................. 12

2.3.4 Connecting the Power Cord for the Docking Station.................. 13

Figure 2.14 Connecting the AC Adapter Power Supplier to the

Docking Station…………………………………....... 13

2.3.5 Connecting the USB Charger to MICA...................................... 14

Figure 2.15 Connecting the AC Adapter Power Supplier to the

Docking Station………………..……………............ 14

2.3.6 Connecting the Keyboard and Mouse........................................ 14

Figure 2.16 Connecting the Keyboard or Mouse.................... 14

Figure 2.17 Connecting the Keyboard or Mouse through Docking

Station.................................................................... 15

2.4 Power LED Signals................................................................................. 15

Figure 2.18 Power LED Indicator .............................................. 15

2.5 Docking Station LAN LED Signals.......................................................... 16

Figure 2.19 LAN LED Indicator .............................................. 16

2.6 Running the BIOS Setup Program.......................................................... 16

2.7 Installing System Software...................................................................... 16

2.8 Installing the Drivers ............................................................................... 17

Figure 2.20 The File Directory on the "Drivers and Utilities" CD-

ROM .......................................................................17

vii MICA Tablet PC User Manual

Chapter 3 Using MICA-071................................. 19

3.1 Power On/Off the System ...................................................................... 20

3.1.1 Stylus Pen ................................................................................. 20

3.1.2 Touchscreen Calibration Function ………….............................. 21

3.1.3 Pen & Touch Settings ……........................................................ 22

3.1.4 Virtual Keyboard ........................................................................ 23

3.2 Bluetooth On/Off..................................................................................... 24

3.3 WLAN On/Off …………….................................................................... 25

3.4 Barcode Function .................................................................................. 26

3.5 Camera Function ................................................................................... 27

Chapter 4 Chipset Setup ................................... 29

4.1 Introduction ............................................................................................ 30

4.2 Installation of Chipset Driver ................................................................. 30

4.3 Further Information ................................................................................ 34

Chapter 5 Audio Setup ...................................... 35

5.1 Introduction ............................................................................................ 36

5.2 Installation of Audio Driver ..................................................................... 36

5.3 Further Information ................................................................................ 40

Chapter 6 Bluetooth Setup................................ 41

6.1 Installation of Bluetooth Driver .............................................................. 42

6.2 Further Information ................................................................................ 44

Chapter 7 GPS Driver Installation .................... 45

7.1 Installation of GPS Driver....................................................................... 46

7.2 Further information................................................................................. 49

Chapter 8 Speaker and Receiver Setup............ 51

8.1 Installation of Speaker and Receiver Driver .......................................... 52

8.2 Further Information ................................................................................ 53

Chapter 9 WIFI Driver Installation .................... 55

9.1 Installation of RFID Driver ..................................................................... 56

9.2 Further Information ................................................................................ 59

MICA Tablet PC User Manual viii

Chapter 1

1 General Information

Display 7" TFT LCD Panel
Touch Panel 5-point P-cap touch panel
Max. Resolution 800 x 1280
Stylus Pen Capacitive stylus pen
Storage

EMMC 32G

WiFi- 802.11 a/b/g/n WLAN (5 G/2.4 G)

Barcode Scanner 1D/2D Barcode scanner

1.1 Introduction

MICA is a multimedia Atom Mobile processor-based computer that is designed to serve as a
Mobile Clinical Assistant (MCA). It is a PC-based system with 7" TFT LCD display and a
stereo audio controller. MICA is a simple, complete and highly integrated mobile multimedia
system which allows system integrators to easily build a Mobile Clinical Assistant Terminal
into their applications.

Common industrial applications include factory automation systems, precision machinery,
and production process control. It is also suitable for many non-industrial applications,
including interactive kiosk systems, entertainment management, and car park automation.
MICA is a reliable, cost-effective solution to meet an application’s processing requirements.

1.2 Specifications

Table 1.1: MICA Specification

Item Description

Dimensions (WþDþH) 121 mm x 200 mm x 14.5 / 24 mm (bottom / top)
Weight 400g

Intel® Atom Processor Bay Trail - T Z3770

CPU and Chipset

- 22 nm system-on-a-chip (SoC)

- 2M Cache, up to 2.39 GHz

Memory LPDDR3 4G
Graphics

Intel® Integrated HD Graphics

Audio

Realtek ALC5642
Internal Speaker x1, Internal microphone x 2, Receiver x1
Docking port x 1

I/O Ports

SD card slot x 1
SIM card slot (Optional) x 1
Line out x 1

Communication

Bluetooth V2.0+EDR / Bluetooth 4.0 LE
3G 850/900/1900/2100 Support HSPA+ (Optional)
GPS 850/900/1900/2100 Support HSPA+ (Optional)
NFC Support ISO14443, 1.0inch

Ingress Protection IP54-rated, Alcohol resistant for cleaning purposes
Thermal Solution Fanless Design

Operating System

Windows 8.1 Industry Pro 64Bits

Camera 8.0 Mega pixel camera with LED light

Auto-focus supported

MICA Tablet PC User Manual 2

Web Camera 2.0 Mega pixel VGA camera

Power button: On the top side of MICA
Barcode scanner buttons: Two orange buttons

Volume control button
Home Key button

Control Button

Indicated LED

Power Adapter

USB Charger

Battery

Programmable button (Default setting):

- P1 for S3 mode

- P2 for WiFi on/off

Power LED & Battery status LED

 Full → Blue
 Charging → Orange

APD WA-20A05FU
INPUT: 100 ~ 240 V, 0.6 A Max., 50/60 Hz
OUTPUT: 5 V, 4 A

Chicony W12-010N3A
INPUT: 100 ~ 240 V, 0.5 A Max., 50/60 Hz
OUTPUT: 5 V, 2 A Max.

Model: MICA-071
Lithium-ion battery (3.7 V @ 4100 mAh)
4 Hr charging time

3 MICA Tablet PC User Manual

Operating Temperature 0° C ~ 40° C
Operating Humidity 10% ~ 90% @ 40° C, non-condensing
Storage Temperature -20° C ~ 60° C
Storage Humidity 10% ~ 95%, non-condensing
Transportation Temperature -20° C ~ 60° C Transportation
Humidity 10% ~ 95%, non-condensing
Certifications

Safety

FCC Part 15 Class B, UL, CE, CB60950, RoHS

1.3 Cleaning/Disinfecting

During normal use MICA may become soiled and should, therefore, be cleaned regularly.
Steps:

1. Wipe MICA with a clean cloth that has been moistened in the cleaning solution.

2. Prepare agent per manufacturer’s instructions or hospital protocol.

3. Wipe thoroughly with a clean cloth.

Caution! Do not immerse or rinse MICA or its peripherals. If you accidentally spill liquid

on the device, disconnect the unit from the power source. Contact your
Biomed personnel regarding the continued safety of the unit before placing it
back in operation.

Do not spray cleaning agent on the chassis.
Do not use disinfectants that contain phenol.
Do not autoclave or clean MICA or its peripherals with strong aromatic,

chlorinated, ketone, ether, or other solvents, sharp tools or abrasives. Never
immerse electrical connectors in water or other liquids.

MICA Tablet PC User Manual 4

Attention! Ne pas immerger ou rincer MICA ou ses périphériques. Si vous renversez

par accident un liquide sur l'appareil, débranchez l'appareil de la source
d'alimentation. Contactez votre Biomed concernant la sécurité continue de
l'unité avant de la remettre en service.
Ne pas pulvériser l'agent de nettoyage sur le châssis.
Ne pas utiliser de désinfectants contenant du phénol.
Ne pas passer à l'autoclave ou MICA propre ou ses périphériques avec
fortes, cétone, éther, ou d'autres solvants, des outils tranchants ou abrasifs
aromatiques chlorés. Ne jamais plonger connecteurs électriques dans l'eau
ou d'autres liquids.

1.4 Dimensions

Figure 1.1 MICA Dimensions

5 MICA Tablet PC User Manual

121mm

200mm

Chapter 2

2 Getting Started

2.1 A Quick Tour of MICA

Before you start to set up MICA, take a moment to become familiar with the locations and
purposes of the controls, drives, connections and ports, which are illustrated in the figures
below.

When placed upright on the desktop, the MICA front panel appears as shown in Figure 2.1.

LED indicator

Ambient sensor

Camera

Figure 2.1 Front View

The volume control button, barcode scanner button and docking connector are on the left side
of the tablet PC.

Figure 2.2 Left Side View

MICA Tablet PC User Manual 7

Receiver

Home Key

Barcode scanner button

Volume control button

Docking connector

Hang hole

The card slots, barcode scanner button and programmable buttons are on the right side of
the tablet PC.

Barcode scanner button

Figure 2.3 Right Side View

The rear view of the tablet PC is depicted in Figure 2.4.
Camera

Camera flash
Speaker

Figure 2.4 Rear View

8 MICA Tablet PC User Manual

Card Slots(Micro SD & SIM card)

Programmable key

Hang hole

LAN
port

HDMI

port

DC in jack

USB 3.0

port

USB 2.0

ports

The top side of the tablet PC contains power button, barcode scanner and headphone jack.

Figure 2.5 Top View

2.2 A Quick Tour of MICA Docking Holder (Optional)

When you place the docking station on the desktop, its front panel appears as shown in Figure

2.6.

Figure 2.6 Front View

MICA Tablet PC User Manual 9

Figure 2.7 Rear View of Docking Station

Power button

Headphone jack

Barcode scanner

Docking connector

2.3 Installation Procedures

2.3.1 Install the Strap (Optional)

This strap is designed for the MICA-071, which make the tablet convenient to hold.

10 MICA Tablet PC User Manual

Figure 2.8 Strap

a. Aim the triangle mark on the strap to the home key to slightly insert the bottom side of the

tablet into the strap.

b. Press to insert the top side of tablet into the strap.

2.3.2 Insert / Hang the Stylus (Optional)

Figure 2.9 Install the Strap

Figure 2.10 Stylus

MICA Tablet PC User Manual 11

Figure 2.13 MICA-071 in Docking Station

2. Align the docking port to the docking connector to insert the tablet into the docking station
and press it right into position.

Note! Before placing the tablet into the docking station, please make sure that the

protective cover of docking port is placed right into its reserved slot.

Figure 2.12 Open and secure the protective cover

2.3.3 Insert the MICA into the Docking Station (Optional)

Figure 2.11 Secure the stylus

a. Hang and secure the stylus through the hang hole of the MICA.
b. Insert and secure the stylus onto the strap.

12 MICA Tablet PC User Manual

2.3.4 Connecting the Power Cord for the Docking Station

Be sure to always handle the power cords by holding the plug ends only. Follow
these procedures in order:

1. Insert the MICA into the docking station as previous section 2.3.3.(See Figure 2.13.).

2. Connect the female end of the power cord to the DC-in jack of the docking station.

3. Connect the 2-pin male plug of the power cord to an electrical outlet.

Figure 2.14 Connecting the AC Adapter Power Supplier to the Docking Station

Step 3

Step 2

2.3.5 Connecting the USB Charger to MICA

Please follow these procedures in order:

1. Open and turn the protective cover of the docking port to the opposite side and
press to lock it into its reserved slot. (See Figure 2.12.)

2. Connect the docking end of the USB charge cable to the docking port of MICA (See
Figure 2.14.).

3. Connect the USB end of the USB charge cable to the USB charger.

4. Insert the 2-pin plug into an electrical outlet.

MICA Tablet PC User Manual 13

2.3.6 Connecting the Keyboard and Mouse

1. Connect the USB mouse and keyboard and docking port of MICA with USB docking cable

(See Figure 2.16.). The USB transfer cable is bundled in the accessory box. A USB hub is
needed for additional USB devices.

Figure 2.16 Connecting the Keyboard or Mouse

Figure 2.15 Connecting the AC Adapter Power Supplier to the Docking Station

Step 3

Step 2

Step 4

14 MICA Tablet PC User Manual

2. Insert the MICA into the docking station as previous section 2.3.3. Connect the USB

mouse and keyboard to USB 2.0 ports of the docking station (See Figure 2.17.).

Figure 2.17 Connecting the Keyboard or Mouse through Docking Station

2.4 Power LED Signals

The LED indicator on MICA shows its charging status.

Power Status LED

 Blue: Full charge
 Orange: Charging

Figure 2.18 Power LED Indicator

MICA Tablet PC User Manual 15

2.5 Docking Station LAN LED Signals

LAN

Figure 2.19 LAN LED

LAN LED

 Left (Active LED)

Data Traffic 10Base OFF
 100Base Green Flashing
1000Base Yellow Flashing

No Data Traffic 10Base OFF
 100Base Green
1000Base Yellow
 Right (Link LED) Green

2.6 Running the BIOS Setup Program

Your MICA has most likely been properly set up and configured by your dealer prior to
delivery. You may still find it necessary to use the BIOS (Basic Input-Output System) setup
program to change system configuration information, such as the current date and time or
your type of hard drive. The setup program is stored in read-only memory. It can be
accessed by pressing the "Del" key on your keyboard immediately after powering on the
computer.

The settings you specify with the setup program are recorded in a special area of memory
called CMOS RAM. This memory is backed up by a battery so that it will not be erased
when you turn off or reset the system. Whenever you turn on the power, the system reads
the settings stored in CMOS RAM and compares them to the equipment check conducted
during the power on self-test (POST). If an error occurs, an error message will be displayed
on screen, and you will be prompted to run the setup program.

2.7 Installing System Software

Recent releases of operating systems from major vendors include setup programs which
load automatically and guide you through hard disk preparation and operating system
installation. The guidelines below will help you determine the steps necessary to install your
operating system on the tablet PC hard drive.

Activ

Link

Note! Some distributors and system integrators may have already pre-installed

system software prior to shipment of your tablet PC.

2.8 Installing the Drivers

After installing your system software, you will be able to set up the 3G(optional), Audio, GPS,
Bluetooth, WIFI and Intel package. All the drivers except the CD-ROM drive driver are stored
in a CD-ROM disc entitled “Drivers and Utilities” which can be found in your accessory box.
The standard procedures for installing the drivers are described in Chapters 4, 5, 6, 7, 8, and
9 respectively.
The directory of drivers on the "Drivers and Utilities" CD-ROM is shown below for reference:

Figure 2.20 The File Directory on the "Drivers and Utilities" CD-ROM

Note! The drivers and utilities used for MICA are subject to change without notice. If

in doubt, check Advantech's website or contact our application engineers for
the latest information regarding drivers and utilities.

Note! The camera or webcam driver might need to be reinstalled after embedded

program upgrades; follow popup screen instructions to complete the driver
installation.

16 MICA Tablet PC User Manual

If required, insert your operating system’s installation or setup diskette into the optical drive
until the release button pops out.
The BIOS supports system boot-up directly from the CD-ROM drive. You may also insert
your system installation CD-ROM disk into the CD-ROM drive.
Power on or reset the system by pressing the "Ctrl+Alt+Del" keys simultaneously.
The MICA Terminal will automatically load the operating system from diskette or CDROM.
If you are presented with the opening screen of a setup or installation program, follow the
instructions on screen. The setup program will guide you through preparation of your hard
drive, and installation of the operating system.

Chapter 3

3 Using MICA-071

3.1 Power On/Off the System

Power On:
Press the power button as shown below to power on the system.

3.1.1 Stylus Pen

You can use a conductive stylus pen to control the system. You can use the pen to click on
the screen and select a file or folder. Double clicking on the screen will act like double
clicking a mouse. The pen can be locked in place on the strap or hang at the hang hole of
the MICA-071 (see section 2.3.2).

MICA Tablet PC User Manual 18

Power Off：
By using power button:
Press and hold the Power button for at least 4 seconds and Slide to turn off the tablet as the

pop-up message indicates.
By using Charms:

1. Swipe from the right edge of the screen to access Charms.

2. Tap “Settings” → “Power” → “Shut down” to turn off the tablet.

Turning Off the Screen
By using power button:
Press the Power and Sleep/Wake button to turn off the screen.
By using Charms:

1. Swipe from the right edge of the screen to access Charms.

2. Tap “Settings” → “Power” →“Sleep” to turn off the screen.

NOTE: If your tablet is in a sleep state (tablet is on, but screen is off), press the Power
button.

19 MICA Tablet PC User Manual

3.1.2 Touchscreen Calibration Function

The P-cap touchscreen calibration function is found in the control panel. Please press the
calibrate button as shown in the image to start the process.

MICA Tablet PC User Manual 20

3.1.3 Pen & Touch Settings

The pen and touch setting function is found in the control panel. Select a touch action and
then press settings button as shown in the image to set the corresponding touch action.

21 MICA Tablet PC User Manual

3.1.4 Virtual Keyboard

This is a tool for keyboard input. The tool will be automatically enabled after the system boot
up completes. Click on any text input box to pop up the virtual keyboard as following.

Tap the shortcut of “On-Screen Keyboard” to enable it.
You can also enter “Control Panel” –“Ease of Access Center” and select “Start On-Screen

Keyboard” to run the On-Screen Keyboard.
Or press the WIN key + R, and input “osk” and tap Enter to run it.
Search or find the “On-Screen Keyboard” in Apps and tap to run it.

3.2 Bluetooth On/Off

The Bluetooth function default setting is “On” after system is turned on. Note: Please turn
off the Bluetooth to avoiding unnecessary battery consumption if you do not have to use it.

To disable the function, please follow the instructions below.

1. Press Win key + C or swipe in from right edge of the screen, tap the settings icon, and

then tap “Change PC settings”.

2. Tap “PC and device” and then select “Bluetooth”, you can turn on or turn off the

Bluetooth function.

MICA Tablet PC User Manual 22

23 MICA Tablet PC User Manual

3.3 WLAN On/Off

The wireless function default setting is “On” after system power up.
If you would like to disable the WLAN function, please follow the instructions below.

1. Tap the triangle mark on taskbar, and then tap “WLAN” icon.

2. Then find and switc the wireless connection to “Off” position.

3. A cross mark appears on “WLAN” icon.

3.4 Barcode Function

The Barcode program (MICA-071_Barcode) can be enabled when the system is turned on.
Note: Please remove the Advantech Barcode program from startup if the Intel SDK is
installed. Please follow the instructions below.

1. Press the Barcode button shown below. A sensor light will be illuminated for 3

seconds.

2. During these 3 seconds, a target can be scanned using the sensor area found on the

back side of the device. To improve accuracy, please adjust the distance between
target and device until the data has been successfully scanned. When successful the
system will sound a beep.

3. The Barcode program can output scanned data into any blank text field.

MICA Tablet PC User Manual 24

25 MICA Tablet PC User Manual

3.5 Camera Function

Tap “Start” icon on the taskbar or on the charms to enter the Start screen. Find and click
the “Camera” icon to enable the camera function and you can shoot photos by taping the
camera icon on the right of the screen.

Chapter 4

4 Chipset Setup

4.1 Introduction

The MICA uses an Intel® Atom™ Bay Trail - T Z3770 processor, 22 nm system-on-a-chip
(SoC), which consists of an integrated graphics controller, memory controller, and I/O
controller. It is going to offer Bluetooth, WiFi, GPS, 3G/LTE, PMIC, Sensor Hub, NFC, Audio
Codec, Panel, HDMI, Front Camera, Rear Camera, Touch Controller, NDR Flash, eMMC,
SD Card and USB 3.0/2.0.

4.2 Installation of Chipset Driver

Complete the following steps to install the chipset driver. Follow the procedures in the flow
chart that apply to the operating system that you are using with MICA.

Step 1. Double click the driver file and click next button.

MICA Tablet PC User Manual 27

Step 2. Click Next button for license agreement.

28 MICA Tablet PC User Manual

Step 3. Click Next button for installation information.

Note! The following Windows illustrations are examples only. You must follow the

flow chart instructions and pay attention to the instructions which appear on
your screen.

MICA Tablet PC User Manual 29

Step 4. The program will copy relevant files to the system; tap Next button to install.

30 MICA Tablet PC User Manual

Step 5. Tap Finish button to restart system.

4.3 Further Information

For further information about the CHIPSET, VGA installation in your MICA, included driver
updates, troubleshooting guides and FAQ lists, please visit the following web resources.

Advantech websites: www.advantech.com

MICA Tablet PC User Manual 31

Chapter 5

5 Audio Setup

5.1 Introduction

Complete the following steps to install the Audio driver. Follow the procedures in the flow
chart that apply to the operating system that you are using.

5.2 Installation of Audio Driver

Step 1. Tap and hold the Start icon on the left of the taskbar, tap “Device Manager” to open

it, and uninstall the “Realtek I2S Audio Codec ” as following picture shows.

Step 2. Tap/click OK button to uninstall it.

MICA Tablet PC User Manual 33

Note! The Windows illustrations above are examples only. You must follow the flow

chart instructions and pay attention to the instructions which appear on your
screen.

34 MICA Tablet PC User Manual

Step 3. Tap/click the scan icon for hardware changes.

Step 4. Update Driver Software.

MICA Tablet PC User Manual 35

Step 5. Tap “Browse my computer for driver software”.

Step 6. Find and open Audio_Update folder, select the Realtek audio driver folder, and

then tap OK.

Step 7. Select a destination folder using the Browse button, and then tap Next to install

the driver software.

Step 8. Tick Always trust software from “Realtek Semiconductor Corp”. and tap Install to

continue.

36 MICA Tablet PC User Manual

5.3 Further Information

For further information about the Audio installation in your MICA, included driver updates,
troubleshooting guides and FAQ lists, please visit the following web resources.

Advantech websites: www.advantech.com

Step 9. After the driver software is installed, tap Close to end the process.

MICA Tablet PC User Manual 37

Chapter 6

6 Bluetooth Setup

6.1 Installation of Bluetooth Driver

Step 1. Tap and hold the driver application, and tap Run as administrator to start

installation.

Step 2. Tap Next button to continue.

Note! The above Windows illustrations are examples only. You must follow the flow

chart instructions and pay attention to the instructions which appear on your
screen.

MICA Tablet PC User Manual 39

40 MICA Tablet PC User Manual

Step 4. Tap Finish button to end process.

Step 3. Installation completes; tap Next button.

MICA Tablet PC User Manual 41

6.2 Further Information

For further information about the touch installation in your MICA, included driver updates,
troubleshooting guides and FAQ lists, please visit the following web resources.

Advantech websites: www.advantech.com

Chapter 7

7 GPS Driver Installation

7.1 Installation of GPS Driver

Step 1. Tap and hold the driver application, and tap Run as administrator to start

installation.

Step 2. Wait for installation.

Note! The following Windows illustrations are examples only. You must follow the

flow chart instructions and pay attention to the instructions which appear on
your screen.

MICA Tablet PC User Manual 43

Step 3. Tap/click Next button to continue installation.

Step 4. Tap/click Next button to accept license agreement and continue installation.

44 MICA Tablet PC User Manual

MICA Tablet PC User Manual 45

Step 5. Tap/click Install button to complete installation.

Step 6. When complete installation, tap/click Next button.

46 MICA Tablet PC User Manual

Step 7. Tap Finish button to complete installation.

7.2 Further information

For further information about the Ethernet installation in your MICA, included driver updates,
troubleshooting guides and FAQ lists please visit the following web resources.

Advantech websites: www.advantech.com

Chapter 8

8Speaker and Receiver

Setup

8.1 Installation of Speaker and Receiver Driver

Step 1. Tap and hold the driver application, and tap Run as administrator to start

installation

Step 2. Select Speaker to continue setup.

MICA Tablet PC User Manual 48

Step 3. Select Receiver to continue setup.

Note! The Windows illustrations above are examples only. You must follow the flow

chart instructions and pay attention to the instructions which appear on your
screen.

8.2 Further Information

For further information about the RFID installation in your MICA, included driver updates,
troubleshooting guides and FAQ, lists please visit the following web resources.

Advantech websites: www.advantech.com

49 MICA Tablet PC User Manual

Chapter 9

9 WIFI Driver Installation

9.1 Installation of WiFi Driver

Step 1. Open Device Manager, tap and hold the Broadcom 802.11abgn wireless SDIO

Adapter and tap Properties on pop-up window.

Step 2. Tap Update Driver… button, and tap OK to continue.

MICA Tablet PC User Manual 51

Step 3. Use Browse button to select driver file folder and tap OK button.

Step 4. Select a destination folder by using the Browse button. Tap/click Next

button to continue installation.

52 MICA Tablet PC User Manual

Step 5. Tick Always trust software from “Broadcom Corporation”. and tap Install to

continue.

Step 6. Select program folder and click Next button to continue.

MICA Tablet PC User Manual 53

Step 7. After the driver software is installed, tap Close button to end the process.

54 MICA Tablet PC User Manual

Note! The Windows illustrations above are examples only. You must follow the flow

chart instructions and pay attention to the instructions which appear on your
screen.

9.2 Further Information

For further information about the WIFI installation in your MICA, included driver updates,
troubleshooting guides and FAQ lists please visit the following web resources.

Advantech websites: www.advantech.com

www.advantech.com

Please verify specifications before quoting. This guide is intended for reference
purposes only.
All product specifications are subject to change without notice.
No part of this publication may be reproduced in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permis-
sion of the publisher.
All brand and product names are trademarks or registered trademarks of their
respective companies.
© Advantech Co., Ltd. 2009