The information in this document is subject to change without prior notice in order to improve
reliability, design and function and does not represent a commitment on the part of the
manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or documentation,
even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are reserved.
No part of this manual may be reproduced by any mechanical, electronic, or other means in any
form without prior written permission of the manufacturer.
Trademarks
CardSoft is a trademark of SystemSoft Corporation. AutoCAD and Autoshade are trademarks of
Autodesk, Inc. IBM, OS/2, and VGA are trademarks of International Business Machines Corp.
Lotus, 1-2-3, and Symphony are trademarks of Lotus Development Corp. Windows, Word, MSDOS, and Microsoft are trademarks of Microsoft Corp. VESA is a trademark of Video
Electronics Standards Association.
Other product names mentioned herein are used for identification purposes only and may be
trademarks and/or registered trademarks of their respective companies.
Limitation of Liability
While reasonable efforts have been made to ensure the accuracy of this manual, the manufacturer
and distributor assume no liability resulting from errors or omissions in this manual, or from the
use of the information contained herein.
i
Notices
Federal Communications Commission Radio Frequency Interference
Statement
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses, and can radiate radio frequency energy and if not installed and used in accordance with
the instruction manual may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio TV technician for help.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. Shielded interface cables and a nonshielded AC power cord must be used in order to comply with emission limits.
The antenna(s) used for this transmitter must be installed to provide a separation distance of at
least 20 cm from all persons and must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment is to be used with power supply:
I/P: 100-240 Vac, 50-60Hz, 1.5A
O/P: 20Vdc, 2.5A
There is no internal power supply.
ii
Canadian DOC Notice For Class B Computing Devices
This Class B digital apparatus meets all requirements of the Canadian Interference - Causing
Equipment Regulations.
Cet appareil numerique de la classe B repecte toutes les exigences du Règlement sur le matèriel
brouilleur du Canada.
iii
Page intentionally left blank
iv
Table of Contents
Chapter 1: Before you Start---------------------------------------------------------------------------------1
Conventions of This Manual..........................................................................................................................1
Things you must remember before working on your computer.....................................................................6
Welcome to the Notebook PC........................................................................................................................9
Getting to Know Your Computer...................................................................................................................10
Chapter 3: Getting Started ----------------------------------------------------------------------------------23
Connecting to a Power Source.......................................................................................................................23
Turning On Your Notebook Computer..........................................................................................................24
Operating on Battery Power...........................................................................................................................24
Chapter 4: Using the Notebook Computer -------------------------------------------------------------27
Adjusting the LCD Screen Display................................................................................................................ 27
A Tour of the Notebook’s Keyboard .............................................................................................................28
The TouchPad................................................................................................................................................ 29
Connecting an External Tracking Devices.....................................................................................................30
The CD-ROM/DVD-ROM/Combo Drive .....................................................................................................31
PCMCIA Cards and Expansion Sockets........................................................................................................32
Power Saving Modes .....................................................................................................................................33
Navigating through BIOS Setup ....................................................................................................................47
Accessing the BIOS Setup Program .............................................................................................................. 47
The Menu Bar ................................................................................................................................................ 48
The Legend Bar .............................................................................................................................................48
General Help.................................................................................................................................................. 49
The Main Menu .............................................................................................................................................50
The Advanced Menu...................................................................................................................................... 51
The Security Menu.........................................................................................................................................52
The Boot Menu .............................................................................................................................................. 53
The Exit Menu ...............................................................................................................................................54
Chapter 8: The Software Utilities Disks -----------------------------------------------------------------55
Locating a Problem........................................................................................................................................ 74
Checking Cables and Connections.................................................................................................................75
The Power-On Self Test.................................................................................................................................75
General Hardware Problems.......................................................................................................................... 76
Contacting Your Dealer .................................................................................................................................78
Chapter 11: Upgrading your System---------------------------------------------------------------------80
Upgrading your Memory ...............................................................................................................................80
The Easy to Upgrade HDD Module............................................................................................................... 81
Upgrading your System CPU......................................................................................................................... 82
Use this manual will help you get the most from your notebook computer.
If you are an experienced user of computers and/or Microsoft’s Windows operating systems,
you might find it useful to read the Quick Start Guide that comes along with your accessories.
If you are a less experienced user, you should through the manual carefully before using your
system.
Whether or not you are an experienced user, you should consult on the Troubleshooting Chapter
if you encounter any problems with your notebook.
Safety Precautions
This section is designed to assist you in identifying potentially unsafe conditions while working
with this product. Required safety features have been installed in the computer to protect you
from injury. However, you should use good judgment to identify potential safety hazards:
1. Please read these safety instructions carefully.
2. Please keep this User's Manual for later reference.
3. Please disconnect this equipment from AC outlet before cleaning. Don't use liquid or
sprayed detergent for cleaning. Use moisture sheet or cloth for cleaning.
4. For pluggable equipment, that the socket-outlet shall be installed near the equipment and
shall be easily accessible.
5. Please keep this equipment from humidity.
6. Lay this equipment on a reliable surface when installed. A drop or fall could cause injury.
7. Make sure to use the right voltage for the power source when connecting the equipment to
the power outlet.
1
8. Place the power cord in such a way that people can not step on it. Do not place anything
on top of the power cord.
9. All cautions and warnings on the equipment should be noted.
10. If the equipment is not use for a long time, disconnect the equipment from the main power
outlet to avoid being damaged by transient overvoltage.
11. Never pour any liquid into the opening, this could cause fire or electrical shock.
12. Never open the equipment. For safety reason, the equipment should only be opened by a
qualified service personnel.
13. If on the following situations arises, get the equipment checked by a service personnel:
a. The Power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment has not worked well or you cannot get it work according to the user's
manual.
e. The equipment has dropped and damaged.
f. If the equipment has obvious sign of breakage.
14. Do not leave this equipment in an environment unconditioned, storage temperature above
60°C (140°f), it may damage the equipment.
15. The unit can be operated at an ambient temperature of max. 35°C.
16. The sound pressure level at the operators position according to IEC 704-1: 1982 is equal or
less than 70 dB(A).
17. Power Cord Requirements
The power cord set used with the AC adaptor must meet the requirements of the country
where you use the AC adaptor, whether it is 100-120 or 200-240 Vac. The following
information explains the requirements for power cord set selection.
The cord set must be approved for the country in which it is used.
The appliance coupler must have a configuration for mating with a
CEE22/EN6032/IEC 320 appliance inlet.
A. For U.S. and Canada:
The cord set must be UL Listed and CSA Certified.
The minimum specifications for the flexible cord are No. 18 AWG.
2
B. For Japan:
All components of the cord set must bear a “PSE” or “ T ” mark and registration
number in accordance with the Japanese Dentori Law.
The minimum specifications for the flexible cord are .75m ㎡ conductors.
C. For Other Countries:
The cord set fittings must bear the certification mark of the agency responsible
for evaluation in a specific country.
The flexible cord must be of a HAR (harmonized) type H03VV-F.
The cord set must have a current capacity of a least 2.5 Amperes and voltage
rating of 125 or 250 Vac.
18. When using your telephone equipment, basic safety precautions should always be followed
to reduce the risk of fire, electric shock and injury to persons. These precautions includes
the following:
Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink
or laundry tub, in a wet basement or near a swimming pool.
Avoid using a telephone (other than a cordless type) during an electrical storm. There
may be a remote risk of electric shock from lightning.
Do not use the telephone to report a gas leak in the vicinity of the leak.
Use only the power cord indicated in this manual.
19. Do not use the AC adapter near open water or other liquids. Never spill liquid into the AC
adapter.
20. Laser Warning: Laser Class I Product Caution - Invisible laser radiation when open avoid
exposure to beam.
21. Danger of explosion if battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer's instructions. Never remove the battery pack while the power is on as
this may result in data loss when the system loses power.
22. The input receptacle is used as the main disconnecting device.
Wichtige Sicherheitshinweise
1. Bitte lesen Sie diese Hinweis sorgfältig durch.
2. Heben Sie dirse Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Versenden Sie Keine
3
Flüssig- oder Aerosolreiniger. Am besten eignet sich ein angefeuchtetes Tuch zur
Reinigung.
4. Die Netzanschluβsteckdose soll nahe dem Gerät angebracht und leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein Kippen oder Fallen
könnte Beschädigungen hervorrufen.
7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.
8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen kann. Es sollte auch
nichts auf der Leitun abgestellt werden.
9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu beachten.
10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz
trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
11. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeien in das Gerät
gelangen. Dies könne einen Brand bzw. Elektrischen Schlag auslösen.
12. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur
von authorisiertem Servicepersonal geöffnet werden.
13. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu trennen und von einer
qualifizierten Servicestelle zu Überprüfung.:
a. Netzlabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend funktioniert oder Sie mit
Hilfe dieser Anleitung keine Verbesserung erzielen.
e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
14. VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der Batterie. Ersatz nur
durch denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des Herstellers.
15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von maximal 35ºC.
16. Die Ausgangswerte dürfen nicht die auf dem Label angegebenen Werte überschreiten.
17. Anforderungen an das Stromkabel
Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den Anforderungen des
Landes, in dem Sie das Netzteil einsetzen, genügen, je nachdem, ob die Netzspannung 100-
4
120 oder 200-240V Wechselspannung beträgt.
Das Kabel-Set muss für das Land, in dem es eingesetzt wird, zugelassen sein.
Der Gerätestecker des Kabels muss in eine CEE22/ EN603/ IEC 320 Buchse
passen.
A. Für die USA und Kanada:
Das Kabel-Set muss UL-gelistet und CSA zertifiziert sein.
Die Minimalanforderungen für das Kabel entsprechen No. 18 AWG.
B. Für Japan:
Alle Teile des Kabel-Sets müssen entsprechend dem japanischen Dentori Law
mit einem „PSE“ or „T”-Symbol markiert sein
Die Minimalanforderungen für das Kabel sind .75m ㎡ Leiter.
Für andere Länder:
Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel derjenigen Stelle, die in
dem jeweiligen Land für die Sicherheitsprüfung zuständig ist, tragen.
Das Kabel muss vom HAR (harmonisierten) Typ H03VV-F sein.
Das Kabel-Set muss eine Stromkapazität von mindestens 2,5 Ampere haben und
Spannungen von 125 oder 250 V Wechselstrom gestatten.
18. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die grundlegenden
Sicherheitsmaßnahmen beachten, um das Risiko von Feuer, Stromschlägen und
Verletzungen zu minimieren. Zu beachten sind u.a. folgende Punkte:
Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie zum Beispiel Badewanne,
Waschbecken, Spülbecken, Waschbottich, in feuchten Kellerräumen oder in der Nähe
von Schwimmbecken.
Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle) während eines Gewitters.
Es besteht das geringe Restrisiko eines Blitzschlages.
Benutzen Sie das Telefon nicht um ein Gasleck zu melden, falls es sich in der Nähe des
Lecks befindet.
Benutzen Sie nur solch ein Stromkabel, wie in dieser Anleitung beschrieben.
19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser oder anderen
Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das Netzteil.
20. Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer Laserstrahl, vermeiden
Sie Kontakt mit dem Strahl bei offenem Gehäuse.
5
21. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß ersetzt wird. Ersetzen
Sie den Akku nur durch einen Akku gleichen oder äquivalenten Typs, der vom Hersteller
empfohlen wird. Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers.
Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem Notebook, da hierdurch Daten
verloren gehen könnten.
22. Der Netzeingabeanschluss dient als Hauptschalter des Geräts.
Things you must remember before working on your computer
Let your computer acclimate itself
Your notebook can easily stand temperature extremes but it doesn’t like rapid changes in
temperature, like going from the cold outdoors to a warm office. Rapid changes in temperature
can cause water droplets to condense inside your case, threatening to damage the electronic parts
inside.
After receiving your notebook when it’s hot or cold outside, try not to power up the computer
immediately, let the computer adjust to the room temperature gradually at least for three to four
hours.
If your system arrives in cold weather, do not apply power to the computer or monitor until
they have been allowed to come to room temperature.
Heat, Cold, Humidity, and Glare
Find a suitable place for your computer that’s not too hot, too cold, too dark, or too bright. Glare
can make it hard to read the screen.
Try to avoid the computer components from being destroyed if it is over heated, so try to
allow plenty of room for air to circulate around the case.
Do not block the ventilation opening.
Do not place your computer in direct sunlight.
Suitable place to work
Your computer will run well wherever you’re comfortable but extremes of temperature and
humidity can be challenging to your system’s parts.
6
There are some things you can tolerate that the computer can’t – things like static electricity, dust,
water, steam and oil. In case you decide to pull over for roadside computing, try to choose a
clean, comfortable work area for your system.
A lithium-ion battery pack will be available when you are traveling. If you are running your
system for the first time on battery power, remove the battery from the package, install it into the
system and recharge the battery to fully prepare for service.
7
Page intentionally left blank
8
IInnttrroodduuccttiioonn
There are more and more people spending large amounts of time in front of computer
monitors now that scientists from many fields including anatomy, psychology, and
occupational safety are involved in the study of ergonomically sound work environments.
A few tips to help you work effectively without a lot of physical discomfort:
Purchase a chair with armrests and good back support. Don't slouch when sitting; keep your
back straight.
Try to place the LCD panel or external monitor so that there is little glare from the sun on
the monitor.
Walk around the room every hour.
Every half hour look away from the computer screen for a few minutes.
Place everything that you need to work within easy reach.
Welcome to the Notebook PC
Congratulations! You’ve just taken a big stride towards turning your notebook into a full-fledged
multimedia computer. The Notebook’s modular design provides maximum expandability without
compromising portability.
Standard Optional
Video Conferencing
Capture Feature
Multimedia Feature
9
Getting to Know Your Computer
Opening the LCD Panel
At the front of the Notebook computer you will find a “Frame LCD” on the middle of the display
panel for you to conveniently raise the LCD panel.
SSttaannddaarrdd VVeerrssiioonn
Use your hand to pull up the “frame LCD”.
At any time you can tilt the display toward or away from you to a comfortable viewing
position.
Press on the Power button to start your computer.
OOppttiioonnaall VVeerrssiioonn
10
Raise the LCD panel and follow the correct procedures as shown on the illustration.
Please don’t raise the LCD panel from the middle part since this is where the camera is
located. The camera is a sensitive device that a strong pull might cause damage to it.
At any time you can tilt the display toward or away from you to a comfortable viewing
position.
Press on the Power button to start your computer.
Important Notices
To avoid damage to the display panel:
Try not to slam the display upon closing it.
For optional model with camera: Please raise down the LCD panel carefully with your hand
assisting the panel until it touches down. Try not to slam the display when closing it, this
might damage the built-in camera.
There is a magnetic sensor on the lower right hand of the LCD panel (inside the speaker)
that will detect the “Lid Switch IC” and shut down the system.
Try not to place any object on top when it is closed or open.
Be sure the system is turned off before you close the display panel.
With the LCD screen open, you will see several features important for operating your Notebook
computer.
11
12
Each of these features is briefly described below.
System Status Indicator Panel
HDD
Indicates that the computer is accessing the hard disk drive.
Numeric Lock
Indicates that the keyboard is in Num Lock mode.
Caps Lock
Indicates when the keyboard is in Caps Lock mode.
Scroll Lock
Indicates when the keyboard is in Scroll Lock mode.
Camera Button (Optional Version)
Use this key to open the built-in camera application.
This button will not function if your model is the standard version with no built-in Camera.
Outlook Express Button
Use this key to open Microsoft's Outlook to send/receive your mail.
Internet Explorer Button
Use this key to open the Internet Explorer.
Wireless Button
Use this key to connect or disconnect the WLAN.
Power Button
Turns your notebook on and off
The Built-in Microphone
Record sounds directly to your notebook hard disk with this built-in microphone
13
Touchpad
The PS/2 compatible mouse will work with the Notebook PC’s TouchPad
simultaneously.
Touchpad Buttons
The buttons below the TouchPad correspond to the left and right buttons on a
standard mouse.
Press the camera button to capture the image with this built-in camera.
The Left Side
15
The Modem Port
Connect a standard phone line directly to the internal modem.
Always disconnect all telephone lines from the wall outlet before servicing or
disassembling this equipment. To reduce the risk of fire use only No. 26 AWG or larger
telecommunication line cord.
Ventilation Opening
Please don't block this opening during operation of the system.
External CRT Port
Connect to any external monitor.
The LAN Port
Connect to a high-speed 10Base-T Ethernet network.
When using a LAN, please use an EMI Shielding Cable to minimize an inteference when
transmitting.
PCMCIA Socket Cover
Open this cover to access the PCMCIA socket.
PCMCIA Button
Press this button to release the PC card.
1394A
A very fast external bus standard that supports data transfer rates of up to 400 Mbps
(400 million bits per second).
16
LLEEDD IInnddiiccaattoorrss
These three LED indicators are separately program for the following functions: Power On,
Suspend Mode and Battery Charge.
Battery Charge
This indicator will lit blue when the battery is in charging status. When the indicator
light turns off, it indicates the system is in full charge.
Power On
This indicator will lit when the notebook is powered On.
Suspend Mode
This indicator will lit when the notebook enter the suspend mode.
17
The Right Side
18
USB Ports
Your computer includes three Universal Serial Bus (USB) port.
The CD-ROM/DVD-ROM or DVD CD-RW Combo
Your Notebook comes with a swappable 24X (or higher) 5.25" IDE CD-ROM/DVDROM/Combo Drive (DVD-ROM+CD-RW), DVD-Dual
CD-ROM release button
Use this button to release the CD-ROM/DVD-ROM from its compartment.
The Rear
DC-In
Plug the AC adapter into this connector.
Kensington Lock
Allows you to connect a special computer lock to secure your system.
19
Loading...
+ 67 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.