ELITEGROUP COMPUTER SYSTEMS 3310ABGX User Manual

ECS 331

i

Preface

Copyright 2005



All Rights Reserved.
The information in this document is subject to change without prior

notice in order to improve reliability, design and function and does not
represent a commitment on the part of the manufacturer.

In no event will the manufacturer be liable for direct, indirect, special,
incidental, or consequential damages arising out of the use or inability to
use the product or documentation, even if advised of the possibility of
such damages.
This document contains proprietary information protected by copyright.
All rights are reserved. No part of this manual may be reproduced by any
mechanical, electronic, or other means in any form without prior written
permission of the manufacturer.

Trademarks

AutoCAD and Autoshade are trademarks of Autodesk, Inc. IBM, OS/2,
and VGA are trademarks of International Business Machines Corp. Lotus,
1-2-3, and Symphony are trademarks of Lotus Development Corp.
Windows, Word, MS-DOS, and Microsoft are trademarks of Microsoft
Corp. VESA is a trademark of Video Electronics Standards Association.
Other product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of
their respective companies.

Limitation of Liability

While reasonable efforts have been made to ensure the accuracy of this
manual, the manufacturer and distributor assume no liability resulting
from errors or omissions in this manual, or from the use of the
information contained herein.

i

Notices

Federal Communications Commission Radio Frequency
Interference Statement

This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that
to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.

FCC Caution: Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate
this equipment.

IMPORTANT NOTE: FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated
with minimum distance 20cm between the radiator & your body. To
maintain compliance with FCC RF exposure compliance requirements,
please avoid direct contact to the transmitting antenna during transmitting.

This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.

We declare that the product is limited in CH1~CH11 by specified firmware
controlled in the USA.

ii

EC DECLARATION OF CONFORMITY (EUROPE)

Hereby, Elitegroup, declares that this product is in compliance with the
essential requirements and other relevant provisions of Directive 1999/5/EC
as listed below

Article 3.1(a): EN 60950, EN50392

Article 3.1(b): EN 301 489-1, 301 489-17
Article 3.2: EN 300 328

0976

Caution:

This equipment is intended to be used in all EU and EFTA countries.

Outdoor use may be restricted to certain frequencies and/or may require a
license for operation. Contact local Authority for procedure to follow. Note:
Combinations of power levels and antennas resulting in a radiated power
level of above 100 mW equivalent isotropic radiated power (EIRP) are
considered as not compliant with the above mentioned directive and are
not allowed for use within the European community and countries that have
adopted the European R&TTE directive 1999/5/EC.

List of national restrictions:

Bulgaria: General authorization required for outdoor use and public service.
France: Outdoor use limited to 10 mW e.i.r.p. within the band 2454-2483.5

MHz.

Italy: If used outside of own premises, general authorization is required.
Luxembourg: General authorization required for public service.
Rumania: On a secondary basis. Individual license required. T/R 22-06 not

implemented

iii

Notice:

Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Shielded interface cables and a non-shielded AC power cord must be used
in order to comply with emission limits.
This equipment is to be used with power supply:
65W
There is no internal power supply.

iv

Table of Content

Before you Start------------------------------------------------------------ 1

Conventions of This Manual ..................................................................... 1

Safety Precautions.......................................................................................1

Wichtige Sicherheitshinweise ...................................................................3

Things you must remember before working on your computer............6

Introduction ----------------------------------------------------------------- 9

Welcome to the Notebook PC...................................................................9

Getting Started------------------------------------------------------------- 15

Connecting to a Power Source.................................................................. 15

Using the Notebook Computer ---------------------------------------- 19

The CD-ROM/DVD-ROM/Combo........................................................... 22

Power Saving Modes.................................................................................. 24

Desktop Operation -------------------------------------------------------- 29

Audio.............................................................................................................29

Connecting Peripheral Devices.................................................................31

Internet Connection (Optional) ---------------------------------------- 33

Using Both DHCP and Static IP for Connection to Internet................. 36

Using Wireless LAN Network for Connection to Internet (Microsoft’s

Service Pack 2) (Optional)......................................................................... 38

Running BIOS Setup------------------------------------------------------ 39

Introduction.................................................................................................. 39

VGA Utilities----------------------------------------------------------------- 47

VGA Utilities............................................................................................... 47

Troubleshooting ----------------------------------------------------------- 55

Locating a Problem..................................................................................... 55

Upgrading your System-------------------------------------------------- 59

Upgrading your System CPU.................................................................... 60

Upgrading your Memory (1)......................................................................61

Upgrading your Memory (2)......................................................................61

The Easy to Upgrade HDD Module..........................................................62

Specification ---------------------------------------------------------------- 63

Detailed Notebook Specifications ............................................................ 63

v

Canadian DOC Notice For Class B Computing Devices

This Class B digital apparatus meets all requirements of the Canadian
Interference - Causing Equipment Regulations.
Cet appareil numerique de la classe B repecte toutes les exigences du
Règlement sur le matèriel brouilleur du Canada.

Personal Inventory

This Notebook computer system is designed for years of productive and
pleasurable computing. Use this section to keep notes about details of
your purchase. Update this section when you add new options.

Date of Purchase:
Dealer’s Name:

Phone:
Address:
E-Mail Address:
WWW Site:

Serial Number:
CPU Type:
Hard Disk Capacity:
Memory Capacity:
Optional Equipment:

vi

BEFORE YOU START

Conventions of This Manual

Use this manual will help you get the most from your notebook computer.

• If you are an experienced user of computers and/or Microsoft’s

Windows operating systems, you might find it useful to read the
Quick Start Guide that comes along with your accessories.

• If you are a less experienced user, you should through the manual

carefully before using your system.

Whether or not you are an experienced user, you should consult on the
Troubleshooting Chapter if you encounter any problems with your
notebook.

Safety Precautions

This section is designed to assist you in identifying potentially unsafe
conditions while working with this product. Required safety features have
been installed in the computer to protect you from injury. However, you
should use good judgment to identify potential safety hazards:

1. Please read these safety instructions carefully.

2. Please keep this User's Manual for later reference.

3. Please disconnect this equipment from AC outlet before cleaning.

Don't use liquid or sprayed detergent for cleaning. Use moisture
sheet or cloth for cleaning.

4. For pluggable equipment, that the socket-outlet shall be installed

near the equipment and shall be easily accessible.

5. Please keep this equipment from humidity.

6. Lay this equipment on a reliable surface when installed. A drop or

fall could cause injury.

7. Make sure to use the right voltage for the power source when

connecting the equipment to the power outlet.

8. Place the power cord in such a way that people can not step on it.

Do not place anything on top of the power cord.

9. All cautions and warnings on the equipment should be noted.

1

10. If the equipment is not use for a long time, disconnect the equipment

from the main power outlet to avoid being damaged by transient
overvoltage.

11. Never pour any liquid into the opening, this could cause fire or

electrical shock.

12. Never open the equipment. For safety reason, the equipment should

only be opened by a qualified service personnel.

13. If on the following situations arises, get the equipment checked by a

service personnel:

a. The Power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment has not worked well or you cannot get it work

according to the user's manual.

e. The equipment has dropped and damaged.
f. If the equipment has obvious sign of breakage.

14. Do not leave this equipment in an environment unconditioned,

storage temperature above 60°C (140°f), it may damage the
equipment.

15. The unit can be operated at an ambient temperature of max. 35°C.

16. The sound pressure level at the operators position according to IEC

704-1: 1982 is equal or less than 70 dB(A).

17. Power Cord Requirements

The power cord set used with the AC adaptor must meet the
requirements of the country where you use the AC adaptor, whether
it is 100-120 or 200-240 Vac. The following information explains
the requirements for power cord set selection.

Ø The cord set must be approved for the country in which

it is used.

Ø The appliance coupler must have a configuration for

mating with a CEE22/EN6032/IEC 320 appliance inlet.

A. For U.S. and Canada:

Ø The cord set must be UL Listed and CSA Certified.
Ø The minimum specifications for the flexible cord are

No. 18 AWG.

B. For Japan:

Ø All components of the cord set must bear a “PSE” or

“ T ” mark and registration number in accordance with
the Japanese Dentori Law.

Ø The minimum specifications for the flexible cord

are .75m㎡ conductors.

2

C. For Other Countries:

Ø The cord set fittings must bear the certification mark of

the agency responsible for evaluation in a specific
country.

Ø The flexible cord must be of a HAR (harmonized) type

H03VV-F.

Ø The cord set must have a current capacity of a least 2.5

Amperes and voltage rating of 125 or 250 Vac.

18. When using your telephone equipment, basic safety precautions

should always be followed to reduce the risk of fire, electric shock
and injury to persons. These precautions includes the following:

Ø Do not use this product near water, for example, near a

bathtub, washbowl, kitchen sink or laundry tub, in a
wet basement or near a swimming pool.

Ø Avoid using a telephone (other than a cordless type)

during an electrical storm. There may be a remote risk
of electric shock from lightning.

Ø Do not use the telephone to report a gas leak in the

vicinity of the leak.

Ø Use only the power cord indicated in this manual.

19. Do not use the AC adapter near open water or other liquids. Never

spill liquid into the AC adapter.

20. Laser Warning: Laser Class I Product Caution - Invisible laser

radiation when open avoid exposure to beam.

21. Danger of explosion if battery is incorrectly replaced. Replace only

with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer's
instructions. Never remove the battery pack while the power is on as
this may result in data loss when the system loses power.

22. The input receptacle is used as the main disconnecting device.

Wichtige Sicherheitshinweise

1. Bitte lesen Sie diese Hinweis sorgfältig durch.

2. Heben Sie dirse Anleitung für den späteren Gebrauch auf.

3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen.

Versenden Sie Keine Flüssig- oder Aerosolreiniger. Am besten
eignet sich ein angefeuchtetes Tuch zur Reinigung.

4. Die Netzanschlußsteckdose soll nahe dem Gerät angebracht und

leicht zugänglich sein.

5. Das Gerät ist vor Feuchtigkeit zu schützen.

6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten.

3

Ein Kippen oder Fallen könnte Beschädigungen hervorrufen.

7. Beachten Sie beim Anschluß an das Stromnet die Anschlußwerte.

8. Verlegen Sie die Netzanschlußleitung so, daß niemand darüber fallen

kann. Es sollte auch nichts auf der Leitun abgestellt werden.

9. Alle Hinweise und Warnungen, die sich am Gerät befinden, sind zu

beachten.

10. Wird das Gerät üeinen längeren Zeitraum nicht benutzt, sollten Sie

es vom Stromnetz trennen. Somit wird im Falle einer Überspannung
eine Beschädigung vermieden.

11. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder

Flüssigkeien in das Gerät gelangen. Dies könne einen Brand bzw.
Elektrischen Schlag auslösen.

12. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der

elektrischen Sicherheit nur von authorisiertem Servicepersonal
geöffnet werden.

13. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu

trennen und von einer qualifizierten Servicestelle zu Überprüfung.:

a. Netzlabel oder Netzstecker sind beschädigt.
b. Flüssigkeit ist in das Gerät eingedrungen.
c. Das Gerät war Feuchtigkeit ausgesetzt.
d. Wenn das Gerät nicht der Bedienungsanleitung entsprechend

funktioniert oder Sie mit Hilfe dieser Anleitung keine
Verbesserung erzielen.

e. Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f. Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.

14. VORSICHT: Explosiongsgetahr bei unsachgemäßen Austausch der

Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnlichen Typ. Entsorgung gebrauchter Batterien
nach Angaben des Herstellers.

15. Dieses Schaltnetzteil kann bis zu einer Außentemperatur von

maximal 35ºC.

16. Die Ausgangswerte dürfen nicht die auf dem Label angegebenen

Werte überschreiten.

17. Anforderungen an das Stromkabel

Das Kabel-Set, das an das Netzteil angeschlossen wird, muss den
Anforderungen des Landes, in dem Sie das Netzteil einsetzen,
genügen, je nachdem, ob die Netzspannung 100-120 oder 200 -240V
Wechselspannung beträgt.

Ø Das Kabel-Set muss für das Land, in dem es eingesetzt

wird, zugelassen sein.

4

Ø Der Gerätestecker des Kabels muss in eine CEE22/

EN603/ IEC 320 Buchse passen.

A. Für die USA und Kanada:

Ø Das Kabel-Set muss UL-gelistet und CSA zertifiziert

sein.

Ø Die Minimalanforderungen für das Kabel entsprechen

No. 18 AWG.

B. Für Japan:

Ø Alle Teile des Kabel-Sets müssen entsprechend dem

japanischen Dentori Law mit einem „PSE“ or „T”­Symbol markiert sein

Ø Die Minimalanforderungen für das Kabel sind .75m ㎡

Leiter.

C. Für andere Länder:

Ø Die Zubehörteile des Kabel-Sets müssen das Prüfsiegel

derjenigen Stelle, die in dem jeweiligen Land für die
Sicherheitsprüfung zuständig ist, tragen.

Ø Das Kabel muss vom HAR (harmonisierten) Typ

H03VV-F sein.

Ø Das Kabel-Set muss eine Stromkapazität von

mindestens 2,5 Ampere haben und Spannungen von
125 oder 250 V Wechselstrom gestatten.

18. Bei der Benutzung Ihres Telefongerätes sollten Sie immer die

grundlegenden Sicherheitsmaßnahmen beachten, um das Risiko von
Feuer, Stromschlägen und Verletzungen zu minimieren. Zu beachten
sind u.a. folgende Punkte:

Benutzen Sie das Gerät nicht in der Nähe von Wasser, wie

zum Beispiel Badewanne, Waschbecken, Spülbecken,
Waschbottich, in feuchten Kellerräumen oder in der Nähe
von Schwimmbecken.

Benutzen Sie kein Telefon (ausgenommen schnurlose Modelle)

während eines Gewitters. Es besteht das geringe
Restrisiko eines Blitzschlages.

Benutzen Sie das Telefon nicht um ein Gasleck zu melden,

falls es sich in der Nähe des Lecks befindet.

Benutzen Sie nur solch ein Stromkabel, wie in dieser

Anleitung beschrieben.

19. Benutzen Sie das Netzteil nicht in unmittelbarer Nähe zu Wasser

oder anderen Flüssigkeiten. Gießen Sie nie Flüssigkeiten über das
Netzteil.

5

20. Achtung Laser: Laser Produkt der Klasse I. Achtung - Unsichtbarer

Laserstrahl, vermeiden Sie Kontakt mit dem Strahl bei offenem
Gehäuse.

21. Es besteht Explosionsgefahr, wenn der Akku nicht ordnungsgemäß

ersetzt wird. Ersetzen Sie den Akku nur durch einen Akku gleichen
oder äquivalenten Typs, der vom Hersteller empfohlen wird.
Entsorgen Sie Akkus entsprechend den Anweisungen des Herstellers.
Entfernen Sie den Akku auf keinen Fall bei eingeschaltetem
Notebook, da hierdurch Daten verloren gehen könnten.

22. Der Netzeingabeanschluss dient als Hauptschalter des Geräts.

Things you must remember before working on your
computer

Let your computer acclimate itself

Your notebook can easily stand temperature extremes but it doesn’t like
rapid changes in temperature, like going from the cold outdoors to a
warm office. Rapid changes in temperature can cause water droplets to
condense inside your case, threatening to damage the electronic parts
inside.
After receiving your notebook when it’s hot or cold outside, try not to
power up the computer immediately, let the computer adjust to the room
temperature gradually at least for three to four hours.

If your system arrives in cold weather, do not apply power to the
computer or monitor until they have been allowed to come to room

temperature.

Heat, Cold, Humidity, and Glare

Find a suitable place for your computer that’s not too hot, too cold, too
dark, or too bright. Glare can make it hard to read the screen.

• Try to avoid the computer components from being destroyed if it is

over heated, so try to allow plenty of room for air to circulate around
the case.

• Do not block the ventilation opening.

• Do not place your computer in direct sunlight.

6

Suitable place to work

Your computer will run well wherever you’re comfortable but extremes
of temperature and humidity can be challenging to your system’s parts.
There are some things you can tolerate that the computer can’t – things
like static electricity, dust, water, steam and oil. In case you decide to pull
over for roadside computing, try to choose a clean, comfortable work area
for your system.
A lithium-ion battery pack will be available when you are traveling. If
you are running your system for the first time on battery power, remove
the battery from the package, install it into the system and recharge the
battery to fully prepare for service.

7

8

INTRODUCTION

Welcome to the Notebook PC

Congratulations on your purchase of the Notebook PC. Your Notebook
features the latest advances in portable computing technology. The
Notebook’s modular design provides maximum expandability without
compromising portability. The high-performance CPU and enhanced IDE
hard drive provides you with extra processing power for handling
complex graphics and running large programs.

Getting to Know Your Computer

Opening the LCD Panel

At the front of the Notebook you will find a retaining latch on the display
panel that locks the display in closed position when the Notebook is not
in use.

9

To avoid damage to the display panel:

1. Try not to slam the display upon closing it.

2. Try not to place any object on top when it is closed or open.

3. Be sure the system is turned off or in suspend mode before you
close the display panel.

With the LCD screen open, you will see several features important for
operating your Notebook computer.

Each of these features is briefly described below.

1. LCD Screen

2. Power/Resume Button

3. Wireless LAN Button

4. Internet Explorer Button

5. Outlook Express Button

6. System Status Indicator Panel

10

Wireless Connection

l move information across the screen

Indicates when the system LAN is functioning.

HDD

Indicates that the computer is accessing the hard disk
drive.

Numeric Lock

Indicates that the keyboard is in Num Lock mode.

Caps Lock

Indicates when the keyboard is in Caps Lock mode. In
this mode, the keyboard produces uppercase text when
you press a key. When you press the Caps Lock key
again, the indicator goes off and the keyboard produces
lowercase text.

Scroll Lock

Indicates when the keyboard is in Scroll Lock mode.
Some applications wil
differently when Scroll Lock is on.

7. The Built-in Microphone

8. TouchPad Buttons

9. TouchPad

The Front

1. Infrared Remote Control

2. LCD Cover Release Latch

3. The CD-ROM/DVD-ROM or DVD CD-RW Combo

11

following functions: Power On,

Suspend Mode and Battery

The Left Side

1. Ventilation Opening

2. Speaker

The Right Side

1. Speaker

2. CardReader

3. USB Ports
LED Indicators

These three LED indicators are
separately program for the

Charge.

1. Battery Charge

This indicator will lit green
when the battery is in
charging status. When the
indicator light turns off, it
indicates the system is in
full charge.

2. Suspend Mode

This indicator will lit when the notebook enter the suspend mode.

3. Power On

This indicator will lit when the notebook is powered On.

12

The Rear

1. Cable TV Input

Before connecting the cable into the connector, be sure to remove
first the cover on the TV connector at the rear of the computer with
the aid of a screw driver.

2. The LAN Port

When using a LAN, please use an EMI Shielding Cable to minimize
an inteference when transmitting.

3. The Modem Port

Always disconnect all telephone lines from the wall outlet before
servicing or disassembling this equipment. To reduce the risk of fire
use only No. 26 AWG or larger telecommunication line cord.

4. Microphone Jack

5. Audio Line Out Jack

6. S-Video Port

7. External CRT Port

8. Ventilation Opening

9. Kensington Lock

10. DC-In Connector

13

The Bottom Panel

1. Hard Disk Drive

2. Battery

3. Battery Release Latch

4. Expansion Compartment

14