i -1
Notice
The information in this user’s manual is subject to change without notice.
THE MANUFACTURER OR RESELLER SHALL NOT BE LIABLE FOR ERRORS
OR OMISSIONS CONTAINED IN THIS MANUAL AND SHALL NOT BE LIABLE
FOR ANY CONSEQUENTIAL DAMAGES, WHICH MAY RESULT FROM THE
PERFORMANCE OR USE OF THIS MANUAL.
The information in this user’s manual is protected by copyright laws. No part of this
manual may be photocopied or reproduced in any form without prior written
authorization from the copyright owners.
Copyright 4/2006
All rights reserved.
Microsoft and Windows are registered trademarks of Microsoft Corporation. DOS,
Windows 95/98/ME/2000/NT/XP are trademarks of Microsoft Corporation.
Product names mentioned herein may be trademarks and/or registered trademarks
of their respective owners/companies.
The software described in this manual is delivered under a license agreement. The
software may be used or copied only in accordance with the terms of the agreement.
This product incorporates copyright protection technology that is protected by U.S.
patents and other intellectual property rights. Use of this copyright protection
technology must be authorized by Macrovision, and is intended for home and other
limited viewing uses only unless otherwise authorized by Macrovision. Reverse
engineering or disassembly is prohibited.
.
i -2
TABLE OF CONTENTS
PREFACE
Symbols and Conventions
Protecting Your Computer - Avoid Abusive Handling and Adverse
Environment
Chapter Summaries
1. GETTING TO KNOW THE BASICS
Performance Features (1-2,3)
System at a Glance (1-4)
Top View (1-4,5,6)
Front View (1-7)
Side Views (1-8,9,10)
Bottom View (1-11,12)
AC Adapter (1-13)
LED Status Indicators (1-14)
OSD Status Indicators (1-15)
Keyboard Features (1-16)
Function (Quick) Keys (1-16)
Windows Keys (1-17)
Embedded Numeric Keypad (1-17)
Touch Pad (1-18)
Graphic Subsystem (1-19)
Adjusting the Display Brightness (1-19)
Extending the Life of the TFT Display Panel (1-19)
Opening and Closing the Display Panel (1-20)
DVB-T Digital Broadcast TV (Optional Device) (1-21,22,23)
Audio Subsystem (1-24)
Adjusting the Volume in Windows (1-24)
Voice Recording (1-24)
Instant-On Multimedia Player (1-25,26,27)
Modem and Modem Setting (Optional Device) (1-28,29)
Ethernet Adapter (1-30)
2. BIOS SETUP AND SECURITY
i -3
Entering the BIOS Setup Screen (2-3)
Leaving the BIOS Setup Screen (2-3)
BIOS Action Keys (2-3)
Modifying the BIOS Settings (2-4)
Main Setup (2-4)
Advance Setup (2-4,5)
Security Setup (2-5,6)
Power Setup (2-6)
Boot Setup (2-7)
Exit Setup (2-8)
3. BATTERY POWER & POWER MANAGEMENT
The Battery Pack (3-2)
Lithium-Ion Battery Technology (3-2)
Battery Low-Power Warning (3-3)
Installing and Removing the Battery Pack (3-4,5)
Charging the Battery and Charging Time (3-5)
Checking the Battery Level (3-6)
Prolonging the Battery’s Life and Usage Cycles (3-6)
Using Windows Power Options (3-7)
Windows’ Power Schemes (3-7,8)
Suspend Modes (3-9,10)
Power Button Action (3-11)
Low Battery Warning (3-12)
Power Manual Quick Access (3-13)
4. UPGRADING YOUR COMPUTER
Upgrading the Hard Disk Drive (4-2,3,4,5,6)
Upgrading the System Memory (4-7,8,9,10,11,12,13,14,15)
Installing the Mini PCI Card to the System (4-16,17,18)
Adding the DVB-T Module (Optional Device) (4-19,20,21)
5. TROUBLE-SHOOTING2
First Step (5-2,3)
Audio Problems (5-4)
Hard Disk Problems (5-5,6)
Optical Drive Problems (5-7)
i -4
Display Problems (5-8)
Keyboard and Mouse Problems (5-9)
CMOS Battery Problems (5-10)
Memory Problems (5-11)
Modem Problems (5-12)
Network Adapter / Ethernet Problems (5-13)
Performance Problems (5-14)
Firewire (IEEE1394) and USB2.0 Problems (5-15)
APPENDIX A Product Specification
APPENDIX B Agency Regulatory Notices
i -5
Preface
Using This Manual
This User’s Manual contains general information about the
hardware and software setup, troubleshooting, and technical
specifications of the notebook computer.
Symbols and Conventions
The following conventions and symbols are used in this manual:
When keys are to be pressed at the same time, a plus (+)
symbol is used. For instance, Fn+F7 means holding Fn and
F7 keys at the same time.
When a series of clicking actions is needed in Windows O/S, [ ]
and > symbols are used. For instance, [Start > Settings >
Control Panel > Display] means clicking the Start icon first,
then the Settings, then the Control Panel, then the Display
icon.
When you need to make a selection with the touch pad (or
mouse), you will be asked to ’select’ or ‘click’ or ‘double-click’,
‘right-click’ the item.
Note:
Text in this format and symbol means specific instructions, commentary ,
sidelights, or any additional information or notes that you should be aware of.
Warning:
given instructions or information could result in damage to your computer or could
cause bodily harm or loss of life.
Text in this format and symbol means that failures to comply with the
i -6
Protecting Your Computer - Avoid Abusive Handling and
Adverse Environment
Follow the advice below will help ensure that you get the most out
of your Investment.
Your computer will serve you well if you take good care of it.
Do not expose the computer to direct sunlight or place it near
sources of heat.
Do not subject it to temperatures below 0
o
35
C (95oF).
o
C (32oF) or above
Do not expose the computer to magnetic fields.
Do not expose the computer to moisture or rain.
Do not spill water or liquid on the computer.
Do not subject the computer to adverse shock and vibration.
Do not expose the computer to dust and dirt.
Do not place objects on top of the computer to avoid damaging
the computer.
Do not place the computer on rocky surfaces.
Here are some ways of taking care of your AC adapter.
Do not connect the adapter to any devices other than your
computer.
Do not let water get into the adapter .
Do not block the ventilation airway of the adapter.
Keep the adapter in a cool and ventilated place.
Do not step on the power cord or place heavy objects on top of
it.
Carefully tuck away the power cord and any cables away from
pedestrian traffic.
When unplugging the power cord, do not pull on the cord itself
but pull on the plug.
i -7
Keep the adapter away from children.
The total ampere ratings of the equipment plugged in should
not exceed the ampere rating of the cord if you are using an
extension cord.
The total current rating of all equipment plugged into a single
wall outlet should not exceed the fuse rating.
Do not connect other A C a dapter to your notebook. This
Notebook uses exclusively the AC adapter:
Lishin 0335C2065 (65W), Liteon PA-1650-01 (65W), Liteon PA-1650-02
(65W), EPS F10653-A(65W)
Lishin 0335A2065 (65W),
When cleaning the computer, observe these steps:
1. Power off the computer and remove the battery pack.
2. Disconnect the AC adapter.
3. Use a soft cloth dampened with water. Do not use liquid or
aerosol cleaners.
Contact your dealer or see your service technician if any of the
following occurs:
Computer has been dropped or the body has been damaged.
Liquid has been spilled into the product.
The computer does not operate normally.
Cleaning the Ventilation Grills:
It is suggested that you clean the ventilation grills regularly to
maintain optimal thermal regulation of the notebook. To do this, you
may use a soft brush or a vacuum cleaner (with appropriate head
adapter) to remove the dust buildup on the ventilation grills.
i -8
Chapter Summaries
The following is a summary of the available chapters and
appendices in this manual.
Chapter 1: Getting to Know the Basics
In this chapter, you will learn the basic operations and features
of your computer. It gives you a gene ral understanding of the
components of your computer.
Chapter 2: BIOS Setup / Security
In this chapter, you will learn how to cha nge various firmware
settings and what the settings mean. Also, you will learn how to
take advantage of the built-in security feature provided by the
BIOS.
Chapter 3: Battery Power & Power Management
In this chapter, you will learn the fundamentals of power
management and how to use them to achieve longer battery life.
Chapter 4: Upgrading Your Computer
In this chapter, you will learn how to up grade the system
memory , the hard disk drive, and to inst all the optional wireless mini
card and the optional DVB-T Module.
Chapter 5: Trouble -Shooting
In this chapter, you will learn how to solve common hardware
and software problems.
Appendix A: Product Specification
In this section, you will find a list of the computer’s system
specifications.
Appendix B: Agency Regulatory Notices
In this section, you will find the general electro-magnetic and
safety regulatory information.
i -9
■ chapter 1 getting to know the basics
CHAPTER▼ ONE
GETTING TO KNOW THE BASICS
This chapter introduces the features and
components of the computer.
1-1
■ chapter 1 getting to know the basics
Performance Features
High Performance Processor with Napa Chipset
The notebook PC is equipped with a powerful Mobile Intel
Pentium M Yonah dual-core (Core Duo) or Mobile Intel
Pentium M Yonah single-core (Core Solo) processor.
Together with the latest Intel Napa chipset and
technologies, the system offers very advanced PC
performances.
Advanced Graphic Engine
The Intel 945GM Express chipset is integrated with the
next-generation Intel Graphics Media Accelerator GMA950.
Wide-Screen LCD Display
The computer is equipped with a wide-screen 14.1-inch
TFT high-resolution display panel for the best cinematic
viewing experience.
Digital TV Receiver (Optional DVB-T module)
The optional DVB-T (Digital Video Broadcast – Terrestrial)
module allows you to watch high-quality digital broadcast
TV on your notebook computer.
Instant-On Multimedia Player (Optional)
With a touch of the button, you can quickly launch the
unique Instant-On multimedia player that allows you to play
video, view pictures, and listen to music without having to
boot to Windows.
Mobile 3G Telecom Module (Optional Device)
The optional 3G communication module allows you to
receive digital entertainment services on your notebook
computer via the 3G telecom networks.
ExpressCard Technology
1-2
■ chapter 1 getting to know the basics
ExpressCard (type I, 34mm) is the next-generation of the
PC Card standard. The bus interface is based on the two
standards: PCI Express for high-performance I/O and
USB2.0 for variety of devices.
Expandability
The system offers upgradeable hard disk drive and 2 DDRII
SDRAM sockets for expansion, allowing the user to easily
increase the storage and system capacities as the need
arises.
Built-in Multiple Card Reader
There is built-in 4-in-1 card reader to access many of the
portable media formats (SD Card, MS Card, MMC Card,
and MS-Pro Card).
Gigabit Ethernet Port
The system provides built-in 10/100/1000Mbps Ethernet
network adapter for high bandwidth network connection.
Firewire (IEEE1394 / 1394a) and USB2.0 ports
In addition to a full array of built-in I/O por
ts, the computer
offers IEEE1394 for ultra high-speed connection to high
bandwidth digital video devices and USB2.0 ports to
connect to any USB-based peripheral devices.
Wireless LAN
The internal Wireless LAN module allows your notebook to
connect wirelessly to other 802.11-enabled systems,
devices, or network.
1-3
■ chapter 1 getting to know the basics
System At A Glance
Top View
1. LCD Display
The panel is where the system content is displayed.
2. LED Status Indicator
The LED Status indicators reveal the status of the system
power state, battery-charging state, Instant-On/Suspend state,
and the WLAN switch enabling and disabling. See the LED
Status Indicator Section for details.
1-4
■ chapter 1 getting to know the basics
3. Keyboard
The keyboard is used to enter data. (See Keyboard Section for
details.)
4. Touch Pad
The touch pad is a built-in pointing device with functions similar
to a mouse.
5. Built-in Microphone
The built-in microphone records sound.
6. Instant-On Multimedia Player Launch Button (Optional) /
Silent Mode Button
When the system is powered off, pressing the key launches
Instant-On multimedia application that allows you to watch
movies files, listen to music, or view photos in the optical drive,
hard disk drive, or external storage without having to boot to
Windows. Press the key again to turn off the notebook. Please
go to Instant-On Multimedia Player Application section in this
chapter for more information.
When the system is in Windows, pressing the key enables the
system to lower its power usage; therefore the fan speed is
reduced to achieve lowest operating noise.
When Silent Mode is enabled, the
LED status indicator
shows steady green light.
7. Power / Suspend Button
The power/suspend button turns the notebook on and off and it
also acts as a system suspend key. Press momentarily to turn
on the system. Press and hold for at least 4 seconds to turn off
the system. How this key behaves can be defined in [Start >
Settings > Control Panel > Power Options > Advanced] menu.
Press the power / suspend button again to return from the
suspend mode. (See Chapter 3 for more details on system
1-5
■ chapter 1 getting to know the basics
suspend function.)
When the system is in Suspend Mode, the
indicator shows blinking green light.
LED status
1-6
■ chapter 1 getting to know the basics
Front View
Warning:
damage the display
Do not place any heavy objects on the top of notebook. This may
1. Wireless On/Off Switch
Use the Switch to disable or enable the Wireless function.
When Wireless LAN function is enabled, the
indicator shows steady blue light.
2. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.
LED status
1-7
■ chapter 1 getting to know the basics
Side Views
Warning:
damage the display
Do not place any heavy objects on the top of notebook. This may
1. Optical Drive and Disk Eject Button and Manual Eject Key
Hole
If your computer comes with the Combo drive, DVD-Dual, or
Super-Multi drive, you may save data onto a CD-R / CD-RW or
DVD RW disc. Press the eject button to eject the disk tray. The
manual eject keyhole allows you to manually eject a jammed
disk.
2. External VGA Port
The VGA video output port is for connecting the external LCD
monitor or projector.
3. Power Jack (DC-in)
The DC-out jack of the AC Adapter connects here and powers
the computer.
1-8
■ chapter 1 getting to know the basics
4. Modem Port / Port or Antenna Connector for DVB-T Digital
Broadcast TV (Optional Device)
This is where you plug the phone jack (RJ-11) for fax/modem
functions.
For certain configuration, your computer may be installed with
the optional DVB-T module. In stead of the Modem Port, this is
an antenna connector. If your system has the DVB-T option,
you should plug the antenna into the connector. Please see
DVB-T Digital V i deo Broadcast TV section later in this chapter
for more information. Please see Chapter 4 if you are installing
the DVB-T module by yourself.
5. Kensington Lock Key Hole
A Kensington-type security lock latches to this keyhole for
anti-theft purpose.
6. USB2.0 Port (x3)
The Universal Serial Bus (USB2.0-compliant) port allows you to
connect a wide variety of devices to your computer at a rate of
up to 480 Mbps. This port conforms to the latest USB2.0
plug-and-play standards.
7. Firewire / IEEE1394 / 1394a Port
This is a high-speed serial data port. You may connect any
Fire-wire-ready device to this port.
8. 4-in-1 Card Reader
The 4-in-1 Card Reader supports SD Card, MS Card, MMC
Card, and MS-Pro Card.
9. ExpressCard Slot
The slot is where Express Card (Type I, 34mm) is inserted.
ExpressCard integrates both the PCI-Express bus technology
and USB2.0 interface.
Press the card into the slot to insert. Press the card again to
eject.
10. Stereo Headphone / SPDIF-out Jack
1-9
■ chapter 1 getting to know the basics
The stereo headphone jack (3.5-mm diameter) is where you
connect the headphones or external speakers. Alternatively,
you may connect the S/PDIF output to an external DTS, AC3,
or PCM sound processor / decoder in your home stereo
system.
11. Microphone/Audio Line-in Jack
The microphone/Audio Line-in jack (3.5-mm diameter) is where
you connect a microphone or an external audio input source
such as a CD Player..
12. Ethernet / LAN Port
The port connects to a network hub via the RJ-45 cable and
also conforms to 10/100Base-TX transmission protocol.
13. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.
14. TV (S-Video) Port
The S-Video port permits you to redirect the screen output to a
television set or any analog video playback device. This TV
Port is copyright protected; when DVD movie is played, the
output is scrambled to prevent analog recording.
For certain configuration, this port does not exist or does not
function.
1-10
■ chapter 1 getting to know the basics
Bottom View
1. Battery Pack and Battery Latch
The battery pack is a built-in power source for the notebook.
Slide the battery latch to release the battery pack.
1-11
■ chapter 1 getting to know the basics
2. Ventilation Grill
The fan grill is where air is exchanged to dissipate the internal
heat. Do not block this airway completely.
Warning:
surface only. The bottom case may get very hot.
Do not block the Fan Grill outlet. Place the machine on hard
3. System Device Cover
The system’s processor with cooler assembly, Wireless LAN
module, HDD, and DDR memory module are located under the
case cover. The system memory can be upgraded to a larger
capacity. (See Chapter 4 for instructions on the memory and
HDD upgrade.)
4. Built-in Stereo Speakers
The built-in speakers output the sound in stereo.
5. DVB-T Receiver Module Cover
The optional DVB-T Receiver module is installed under the
cover. Please see Chapter 4 if you are installing the DVB-T
module by yourself.
1-12
■ chapter 1 getting to know the basics
AC Adapter
1. DC-out Connector
The DC-out connector docks to the power jack (DC-in) on the
computer.
2. Adapter
The adapter converts alternating current into constant DC
voltage for the computer.
3. AC Plug
The AC plug plugs to the AC wall outlet.
1-13
■ chapter 1 getting to know the basics
LED Status Indicator
The LED Status Indicator displays the operating status of your
notebook. When a certain function is enabled, an LED will light
up. The following section describes its indication.
System & Power Status Indicators
LED Graphic
Symbol
Indication
Blue light indicates the WLAN module is
active.
Persistent green light indicates the Silent
Mode is enabled.
Blinking green light indicates the
notebook is in the suspend mode.
1-14
Blinking orange light indicates the
battery is being charged.
Blinking green light indicates the battery
power is low when the system is turned
ON.
Persistent green light indicates the
system is turned ON.
■ chapter 1 getting to know the basics
OSD Status Indicator
The On-screen Status Display Indicator displays the operating
status of your notebook. When a certain function is enabled,
the symbol will show up on windows. The following section
describes its indication.
OSD Status Indicators
Action Graphic Symbol
Fn + F3: Audio Mute
Fn + F5: Audio
Volume U p
Fn + F6: Audio
Volume Down
Fn + F7: Display
Brightness Up
Fn+ F8: Display
Brightness Down
Fn + Num Lock:
Numeric Keypad is
Caps Lock:
Capitalization is On
Scroll Lock: Scroll
Lock is On
1-15
■ chapter 1 getting to know the basics
Keyboard Features
Function Keys (Quick Keys)
Graphic
Symbol
For various system controls, press the Fn (Function) key and the Fx key
simultaneously.
Action System Control
Fn + F1 Enters Suspend Mode.
Fn + F3 Turns of the battery warning
Fn + F4 Changes Display Mode:
Fn + F5 Turns Speaker Volume up.
Fn + F6 Turns Speaker Volume down.
Fn + F7 Increases Display Brightness.
Fn + F8 Decreases Display Brightness.
Fn+Num Lk Enables the embedded keypad
Caps Lock When Caps lock is enabled, all
Fn + Scr Lk Press the Fn+Scr Lk key and
beep off or on.
LCD-only, CRT-only and
LCD&CRT.
to work in numeric mode. The
keys act like numeric keypads
in a calculator. Use this mode
when you need to do a lot of
numeric data entry. An
alternative would be to connect
an external numeric keypad.
the characters you enter
become capitalized.
then press ↑or ↓to move one
line up or down.
1-16
■ chapter 1 getting to know the basics
Windows Keys
Your keyboard also has two Windows keys:
1. Start Key
This key allows you to pull up the Windows Start Menu at
the bottom of the taskbar.
2. Application Menu Key
This key brings up the popup menu for the application,
similar to a click of the right mouse button.
Embedded Numeric Keypad
Press Fn+Num Lk to enable the embedded numeric keypad.
The numbers are printed in upper right corner of a key, in a
color different from the alphabets. This key pad is complete
with arithmetic operators (+, -, * , /).
Press Fn+Num Lk to revert to normal character keys.
1-17
■ chapter 1 getting to know the basics
Touch Pad
The built-in touch pad, which is a PS/2-compatible pointing device,
senses movement on its surface. As you move your fingertip on the
surface of the pad, the cursor responds accordingly.
The following items teach you how to use the touch pad:
1. Move your finger across the touch pad to move the cursor.
2. Press buttons to select or execute functions. These two buttons
are similar to the left and right buttons on a mouse. Tapping on the
touch pad twice produces is similar to clicking the left button of a
mouse.
Function Left Button Right
Execution Click twice
quickly
Selection Click once Tap once
Drag Click and hold
Access
Context Menu
Move One
Page Up or
Down
to drag the
cursor
Click once
Button
Tap twice (at the same speed as
Tap twice quickly and on the
Tips on Using the Touch Pad:
1. The double-click speed is timed. If you double-click too slowly,
your notebook responds as if you single-clicked twice.
2. Keep your fingers dry and clean when using the touch pad.
Also keep the surface of touch pad clean and dry to prolong its life.
3. The touch pad is sensitive to finger movements. Hence, the
lighter the touch, the better the response. Heavy touch does not
produce better response.
Equivalent Tapping Action
double-clicking
the mouse button)
second tap hold finger to the touch
pad to drag the cursor
1-18
■ chapter 1 getting to know the basics
Graphic Subsystem
Your computer uses a high performance 14.1-inch active matrix
TFT panel with high resolution and multi-million colors for
comfortable viewing. The Intel integrated GMA950 video graphics
accelerator, which is Microsoft DirectX 9 compatible, performs
graphic rendering at a lighting-fast speed.
Adjusting the Display Brightness
The notebook uses special key combinations, called hot keys,
to control brightness.
Press Fn+F7 to increase the brightness.
Press Fn+F8 to decrease the brightness.
Note: To maximize your battery operating time, set the brightness to the
lowest comfortable setting, so that the internal backlight uses less power.
Extending the Life of the TFT Display Device
Observe the following guidelines to maximize the life of the
backlight in the display.
1. Set the brightness to the lowest comfortable setting
(Fn+F8).
2. When working at your desk, connect your notebook to an
external monitor and disable the internal display Fn+ F4.
3. Do not disable the suspend time-outs.
4. If you are using AC power and have no external monitor
attached, change to suspend mode when not in use.
1-19
■ chapter 1 getting to know the basics
Opening and Closing the Display Panel
To open the display, lift up the lid. Then tilt it to a comfortable
viewing position. The LCD panel has a maximum opening of
135 degrees. Do not push it down forcibly.
To close the display cover, fold it down gently.
Warning:
place any object on top of the computer when the display is closed
To avoid damaging the display, do not slam it when closing. Do not
1-20
■ chapter 1 getting to know the basics
DVB-T Digital Video Broadcast TV (Optional Device)
The optional DVB-T (Digital Video Broadcast – Terrestrial) module
allows you to watch high-quality digital video broadcast TV on your
notebook computer.
If your system has the DVB-T option, you should plug the antenna
into the connector.
You may have to move the antenna close to the window and away
from the building for best reception.
If this is the first time you use the DVB-T module to watch TV, you
need to scan the available channels first. Follow the steps below to
scan the channels.
1. Launch NewSoft Presto!PVR application. Click
open the Settings dialog box, and then click the Device tab.
2. Choose the DVB-T tuner on the Device list.
to
1-21
■ chapter 1 getting to know the basics
1-22
3. Click the Program tab on the Settings dialog box and
click Scan to scan for available channels. If a program (channel)
is found, it will be included in the program list. When finished,
you can choose a program and edit its name.
■ chapter 1 getting to know the basics
4. Press Ok and close the Settings dialog box.
5. You are ready to watch TV.
If you system comes with the DVB-T Module already installed, you
may use NewSoft Presto!PVR to watch and record the TV programs.
Please see Chapter 4 if you are installing the DVB-T module by
yourself. You also need to install the NewSoft Presto!PVR
application from the CD to watch and record TV programs.
1-23
■ chapter 1 getting to know the basics
Audio Subsystem
Your computer’s audio subsystem is Sound Blaster Pro-compatible.
Adjusting the Volume Manually
To increase the volume, press Fn+F5.
To decrease the volume, press Fn+F6.
Adjusting the Audio Volume in Windows
1. Click the speaker symbol in the task tray in Windows.
2. Drag the volume control bar up or down to adjust the volume.
3. To temporarily silence the speaker without changing the
volume setting, click Mute.
Voice Recording
A built-in microphone allows you to record sound. You will need
to use audio processing software to enable the built-in
microphone. For example, you may use Microsoft Sound
Recorder.
1-24
■ chapter 1 getting to know the basics
Instant-On Multimedia Player (Optional)
Instant-On Multimedia Player is an easy way to play DVD disc or
video clips, view pictures, listen to music, and watch digital
broadcast TV (if the optional DVB-T Module is installed). Instant-On
does not work under Windows.
Note:
The following is an easy guide for Instant-On Player. For more
information, please refer to its user guide or Help screen.
Note: Instant-On supports most of the popular media formats; however, it
does not support Animated GIF.
Instant-On Action Keys
Use the following keys to move through the Menu items.
Key Command Description
M Menu
Press to show the General Setup Menu.
Press again to exit the Menu.
Press to show the Instruction Menu and
F1 Instruction Menu
function keys.
Press again to exit the Menu.
↑↓←→ Movement Moves through the Menu
Enter Selection Makes a selection
Because Instant-On does not support touch pad movement, you need
Note:
to use the keys on the keyboard to navigate to desired function. In media mode,
always use F1 to display the function keys.
1-25
■ chapter 1 getting to know the basics
Media File Storage:
Using Instant-On to playback files, you need to store them in:
C:\Documents and Settings\All Users(and every created
users)\Documents\My XXX (Example: Photo files under \My
Photo, Music files under\My Music and Video files under \My
Video).
For example, the first time you are in the Video Mode, the
system will ask to scan the files stored under the specified file
directory and then create a playlist for future use.
Launching the Instant-On Player:
When the computer is powered off and the Instant-On
Multimedia Player Launch Button is pressed, the system
launches the Player application in a few seconds.
1-26
Note: When the computer is already in Windows and the Player Button is
pressed, the system enables the Silent Mode to reduce fan noise.
■ chapter 1 getting to know the basics
Use the ←→ keys to select the Media Mode.
Use F1 to show the Instruction Menu for that Media Mode.
Shutting Down the Instant-On Player:
Press the Instant-On Player button to shut down the computer.
1-27
■ chapter 1 getting to know the basics
Modem
Your computer comes with a 56K V.92 internal fax/modem and a phone
jack (RJ-11), which is located on the left side of your computer.
Use a telephone cable to connect the computer to the telephone wall
outlet.
For certain configuration, there is no Modem Port or Function.
Note:
Connecting the Modem
1. Plug one end of the phone line into the modem port located on
the rear side of the computer. (For EMI compliance, you need to clip
the included EMI CORE to the phone line.)
2. Plug the other end of the line into the analog phone wall outlet.
Depending on where your computer is used, you may need to change
settings in the modem. Correct setting will allow you to maintain a stable
connection in a country where its telecommunication system may be
different to others.
To change the modem setting, do the following:
1. Go to [Start > Settings > Control Panel > Phone and
Modem Options]. Go to Dialing Rules and Edit My Location.
You will see a similar dialog box.
1-28
■ chapter 1 getting to know the basics
2. Click on the pull-down menu and select the country where it is
applicable. Click on OK to exit.
1-29
■ chapter 1 getting to know the basics
Ethernet
Your computer is equipped with a 10/100/1000Base-TX Fast
Ethernet network adapter. Connect the active LAN cable to the
RJ-45 LAN port located on the left side of the computer. This allows
you to access and transmit data in the local area network.
Connecting to the Network
Use Unshielded Twisted Pair (UTP) Ethernet cable only.
1. Insert one end of the UTP cable into the network connector
until the connector snaps securely into the receptacle.
2. Either connect the other end of the cable to an RJ-45 jack
wall outlet or to an RJ-45 port on a UTP concentrator or hub in
the network.
Cabling Restriction for Networks
The following restrictions should be observed for
10/100/1000BASE-TX networks:
The maximum cable run length is 100 meters(m) (328
feet[ft]).
For 100Mbps or 1000Mbps operations, use Category 5
wiring and connections.
1-30
Note:
Consult Windows manual and / or Novell Netware user’s guide for the
software installation, configuration, operation of the network.
■ chapter 2 bios setup and security feature
CHAPTER▼ TWO
BIOS SETUP AND SECURITY FEATURE
In this chapter, you will learn how to
enter the BIOS Setup Menu and
manipulate various hardware control
settings. You will also learn how to use
the built-in security features.
2-1
■ chapter 2 bios setup and security feature
The Setup Utility is a hardware configuration program built into
your computer’s BIOS (Basic Input/Output System). It runs and
maintains a variety of hardware functions. It is a menu-driven
software, which allows you to easily configure and change the
settings.
The BIOS contains manufacture’s default settings for the
computer’s standard operations. However, there are occasions
when you may be required to modify the default settings in the
BIOS.
The BIOS allows you to set up passwords to limit access to users.
This is an important feature because a great deal of vital
information is carried within the computer nowadays. Unauthorized
access can be prevented. Later in this chapter, you will learn how to
use this security feature.
2-2
■ chapter 2 bios setup and security feature
Entering the BIOS Setup Screen
First turn on the power. When the BIOS performs the POST
(Power-On Self Test), press F2 key quickly to activate the AMI
BIOS Setup Utility.
Note:
You may need to press F2 key fairly quickly. Once the system begins to load
Windows, you may have to retry by cycle-power on again
Leaving the BIOS Setup Screen
When you have finished modifying the BIOS settings, exit the BIOS.
It takes a few seconds to record changes in the CMOS.
BIOS Action Keys
Function Key Command Description
Leaves a sub-menu to return to the
ESC Exit
previous menu OR exits the BIOS setup
while saving changes.
Enter Go to Sub Screen Shows the Sub Menu
F1 General Help Shows the Help Screen
F9 Setup Defaults Load default values
F10 Save and Exit
<Tab> Select a field Selects the next field.
↑ Select an item Selects the next upper item.
↓ Select an item Selects the next lower item.
- Lower value Selects the next value within a field.
+ Higher value Selects the next value within a field.
Saves changes and reboots the
computer.
2-3
■ chapter 2 bios setup and security feature
Modifying the BIOS Settings
The AMIBIOS setup main menu is subdivided into sub-menus.
Each menu item is described in this section.
Main Setup
Under this menu, you may change time/date and view basic
processor and system memory information.
Item Selections /
Sub-menu
Date N/A Type in the current date, in MM/DD/YY
Time N/A Type in the current date, in HH:MM:SS
Description
format.
format.
Advanced Setup
►IDE Configuration
Item Selections /
Sub-menu
Primary
IDE
Master
Secondary
IDE
Master
Hard Disk Primary Master is where BIOS tries to
ATAPI CDROM The secondary master controls the
Description
boot from first. The primary master
controls the hard drive.
ATAPI CD-ROM drive.
2-4
The sub-menu is not selectable. Press enter to view information of the
Note:
■ chapter 2 bios setup and security feature
storage device.
Item Selections /
Description
Sub-menu
TouchPad
Support
LCD Auto
DIMM
Function
Enabled
Disabled
Enable
Disable
Enable or disable the built-in touchpad.
[Enable]: The system automatically
reduces the LCD brightness when AC
power is removed to save power.
[Disable]: The LCD brightness remains
the same whether or not AC power is
present.
Security Setup
►Boot Settings Configuration
Item Selections /
Sub-menu
Change
N/A Install or Change the Password
Supervisor
Password
Change
N/A Install or Change the Password
User
Password
Using Password Protection
Two Levels of Password Protection are available. The BIOS
provides both a Supervisor and a User password. If you try to
activate both passwords, the Supervisor password must be set first.
The passwords activate two different levels of protection:
Description
2-5
■ chapter 2 bios setup and security feature
1. System always asks for password every time it is powered on.
2. System asks for password only when you attempt to enter
BIOS utility.
The passwords are encrypted and stored in NVRAM. Make sure
you write them down or memorize them. If you lost the passwords,
the computer may need to be sent back to the factory or to an
authorized service dealer to reset the passwords.
Power Setup
Item Selections /
Sub-menu
Power Button
Mode
High
Performance
Mode
Long Battery
Life Mode
On/Off
Suspend
Enable
Disable
Enable
Disable
Description
[On/Off]: When the power button is
pressed, the system is turned off.
[Suspend]: When the power button is
pressed, the system enters the suspend
mode.
When Enabled, maximum processor
performance can be achieved. The
battery life is lowered.
When Enabled, maximum battery life
can be achieved. The processor
performance is lowered.
Note:
In Windows XP, suspend mode and settings are determined by settings in
the Power Options Properties (Start > Control Panel > Power Options).
2-6
■ chapter 2 bios setup and security feature
Boot Setup
►Boot Settings Configuration
Item Selections /
Sub-menu
Quiet Boot Disabled
Enabled
►Boot Device Priority
Item Selections /
Sub-menu
1st Boot
Device
Removable Dev.
CD/DVD
Hard Drive
Network
Disabled
2nd Boot
Device
3rd Boot
Device
Description
When Enabled, the system will display
OEM logo instead of the POST
messages.
When Disabled, the system will display
POST messages (i.e. devices
information.)
Description
Set the type of device for the 1st drive
BIOS attempts to boot from. If Network is
selected, system will attempt to load boot
sector from the Ethernet port.
Set the type of device for the 2nd drive
BIOS attempts to boot from.
Set the type of device for the 3rd drive
BIOS attempts to boot from.
Note:
If you select Network, the system will attempt to boot from the network.
Note: When the BIOS performs POST, you may also press F12 Key to enable the
Boot Device selection menu. You may choose CD/DVD, Hard Drive, or Network as
the first storage device to boot from. If you have already connected a USB Floppy
Disk Drive before powering up, it will appear as a Removable Device in the Boot
Device selection menu
2-7
■ chapter 2 bios setup and security feature
Exit Setup
Item Selections /
Sub-menu
Saves
N/A After you have completed the BIOS
Changes and
Exit
Discard
N/A Discards changes done so far to any of
Changes and
Exit
Discard
N/A Discards changes done so far to any of
Changes
Load Optimal
N/A Load Optimal Default value for all the
Defaults
Description
settings, select this item to save all
settings, exit BIOS Setup utility, and
reboot. New system settings will take
effect on next power-up. F10 key can be
used for this operation.
the setup questions and exit.
the setup questions.
setup questions. F9 key can be used for
this operation.
2-8
■ chapter 3 battery power & power management
CHAPTER▼ THREE
BATTERY POWER & POWER
MANAGEMENT
In this chapter, you will learn the
fundamentals of power management
and how to use it to achieve longer
battery life.
3-1
■ chapter 3 battery power & power management
In this chapter, you will learn how to operate your notebook on
battery power, how to handle and maintain the battery pack, and
learn about the system’s power saving features.
TFT display, central processor, hard disk drive are the major
hardware subsystems that consume the most power. Power
management deals how these key components should behave to
conserve power . For example, you can have the system turn off its
display after 2 minutes of inactivity to save power. Efficient power
management can help you work longer sessions before having to
recharge the battery.
The Battery Pack
Lithium-Ion Battery
Your notebook uses a six-cell Lithium-Ion battery pack
that provides power when you don’t have access to an
AC outlet.
3-2
Note:
It is necessary that you charge the battery pack for at least 6
hours before using it for the first time.
Note: In the Standby Suspend mode, a fully charged battery loses its
power in roughly 1/2 day or less. When not being used, the battery’s
power will deplete in 1-2 month.
■ chapter 3 battery power & power management
Battery Low-Power Warning
1. Low Battery Warning
Low battery condition occurs when battery power is
reduced to 6%. The green battery status LED indicat or
blinks and the system beeps once every 16 seconds or
so.
2. Very Low Battery Warning
Very Low battery condition occurs at 3 % power
remaining. The green battery status LED indicator blin ks
and the system beeps at 4-second interval.
When the notebook warns you of its low battery condit ion,
you will have about 3-5 minutes to save your current
work.
Warning:
degree Celsius (32 degree F) or above 60 degree C (140F). This may
adversely affect the battery pack.
Do not expose battery packs to temperatures below 0
Note:
Press Fn+F3 to turn off the battery warning beep.
3-3
■ chapter 3 battery power & power management
Installing and Removing the Battery Pack
To Remove the Battery Pack:
1. Place the notebook bottom-side up on a flat and
secured surface.
2. Push the latch and pull the battery’s hard case
away from the notebook.
3-4
■ chapter 3 battery power & power management
To Install the Battery Pack:
1. Place the notebook bottom-side up on a flat and
secured surface.
2. Carefully insert the battery pack into the battery
compartment of the notebook.
Charging the Battery and Charging Time
To charge the battery, while the battery pack is in the noteboo k,
plug the AC adapter into the notebook and an electrical outlet.
The charging time is approximately 4-6 hours when the
notebook is turned off and approximately 6-10 hours when the
notebook is turned on.
When the battery is fully charged, the battery charge indicator
becomes green.
If system runs at heavy loading or in a high temperature environment,
Note:
the battery may not be fully charged. You need to continue to charge it with the
AC adapter plugged in until the charging LED turns green.
3-5
■ chapter 3 battery power & power management
Checking the Battery Level
You can check the remaining battery power in the Windows
battery status indicator, which is located at the lower right-hand
corner of the task bar. (If you do not see a battery or AC-in icon
on the task tray, go to Power Options Properties box and click
on the Advanced tab. Check off ``Always show icon on the task
bar``.)
Alternatively, you can access the power meter by clicking the
Power Options icon in the Windows Control Panel.
Prolonging the Battery’s Life and Usage Cycles
There are ways you can do to prolong the use of battery.
Use the AC adapter wherever AC wall outlet is available.
This will ensure uninterrupted computing.
Purchase additional battery pack.
Store the battery pack in room temperature. Higher
temperature tends to deplete the battery’s power faster.
Make good use of the power management function. Save
To Disk (Hibernate) saves the most energy by storing current
system contents in a hard disk space reserved for this function.
The life expectancy of the battery is approximately 300
recharges.
See the notices section in the beginning of the user
manual on how to care for the battery pack.
Note:
Read Section Protecting Your Notebook in the beginning of this manual
for tips about how to maintain the battery pack.
Note: To achieve optimal battery performance, you may need to do a battery
calibration at a 3-month interval. To do this:
1. Fully charge the battery.
2. Then discharge the battery by entering the BIOS setup screen. (Press F2
key as soon as you turn on the computer. And let it remain at the setup screen
until the battery runs out.
3. Fully charge the battery again.
3-6
■ chapter 3 battery power & power management
Using Windows Power Options
Windows Power Management provides basic power saving
features. In the Windows Power Options Properties [Start >
Settings > Control Panel > Power Options] dialogue box, you
may enter time-out values for display and hard disk drive.
Windows power manager saves power by turning off hard drive
after 1 minute of inactivity, for example.
Windows’ Power Schemes
The power management control panel in Windows XP,
known as Power Schemes, is designed to provide the
user with an easy-to-use interface. The Power Schemes
tab can be found in the Power Options Properties panel
that is accessible via the control panel window.
Schemes are easy to understand, based on notebook
usage scenarios, and control not only processor power
usage but other system peripherals as well.
Go to [Start > Settings > Control Pan el] and double-click
the Power Options icon.
Always on mode puts the processor into maximum
performance mode, which provides no power saving.
The other schemes control processor performance
based on demand. For example, Max Battery mode
lowers the processor’s speed and voltage to conserve
power as much as possible.
3-7
■ chapter 3 battery power & power management
In this dialog box, you can manually set the LCD and
hard drive’s time-out values in the Plugged in colu mn and
in the Running on batteries column. Lower time-out
values will save more battery power.
3-8
Note:
Also consult Windows user guide for more information on how
to use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management
Suspend Mode
Standby Suspend
The system automatically enters this mode after a period
of inactivity, which is set in the Power Schemes dialog
box. In Standby mode, hardwa re devices, such as
display panel and hard disk, are turned off to conse rve
energy.
Hibernate Suspend
In this mode, all system data are saved in the hard disk
before powering down. When this mode is activated, all
system state and contents are saved to the hard disk
drive after a period of inactivity defined by the user. No
power or very little power is drawn from the battery
module under this mode.
However, depending on how much RAM that have been
installed on your computer, the amount of time the
system requires to restore all its previous contents can
range from 5 to 20 seconds.
For Windows 2000 / XP users, hibernation is handled by
the operating system; therefore, no special disk partition
or disk file is necessary.
If you wish to activate Hibernate mode, you need enable
Hibernate Support in the Hibernate tab of the Power
Options menu.
3-9
■ chapter 3 battery power & power management
3-10
Note:
Do not install or remove the memory module when the system
is in the suspend mode.
Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management
Power Button Action
The notebook PC’s power button can be set to turn of f
the system or activate the suspend mode.
Go to [Start > Settings > Control Panel > Power Options]
and click on the Advanced tab. In the pull-down menu,
select how you wish the power button to work as.
Note:
Actual dialogue box shown above may appear slightly different.
Warning:
pull-down menu, DO NOT select Do nothing – otherwise the system will
still run at high speed while the processor’s fan grill is fully blocked by
the closed LCD panel. The heat will damage the LCD panel.
In the When I close the lid of my portable computer
3-11
■ chapter 3 battery power & power management
Low Battery Warning
You can define when and how the system warns you of
its battery-low condition.
Go to the Alarms tab in the Power Options Properties box.
If you wish to hear audible beeps, click on the Alarm
Action button and put a check on Sound Alarm.
3-12
Note:
Consult Windows user guide for more information on how to
use Windows power management functions.
Note: Actual dialogue box shown above may appear slightly different.
■ chapter 3 battery power & power management
Power Menu Quick Access
Instead of making specific selections in the Power
Options Properties box, you can quickly and easily
specify which pre-set power saving function you desire
by clicking on the Battery icon at the lower right-hand
corner of the task bar. (If you do not see a battery or
AC-in icon, go to Power Options Properties box and click
on the Advanced tab. Check off ``Always show icon on
the task bar``.) Select Max Battery if you want the system
to enter suspend mode more often. Or, select Always On
if your notebook PC is plugged into an AC power source.
Actual dialogue box shown above may appear slightly different.
Note:
3-13
■ chapter 4 upgrading your computer
CHAPTER▼ FOUR
UPGRADING YOUR COMPUTER
In this chapter, you will learn how to
upgrade the DRAM, hard disk drive, and
to install the optional wireless LAN
mini-Card and DVB-T Module.
Warning:
the dealer or the shop for the hardware upgrade.
Before you perform the hardware upgrade, please turn off the system,
unplug the AC adapter, remove the battery pack and also disconnect
the LAN and Modem cables first for your safety.
When the hardware upgrade is completed, please be sure to fasten all
the screws before turning on the notebook.
We strongly recommend that you return the notebook to
4-1
■ chapter 4 upgrading your computer
Upgrading the Hard Disk Drive
Replacing the original drive with one of larger capacity can in crease
the hard drive capacity of your computer. The computer uses a 9.5
mm (height), 2.5-inch Serial ATA type hard disk.
Be sure to make a backup copy of all your data before attempting
this operation.
Warning:
instructions carefully or have a qualified technician install it for you. Damages due to
mishandling of this procedure are NOT covered by the manufacture’s warranty.
Hard drive upgrade is a delicate process. Please observe the following
Warning:
Do not drop or apply any shock.
Do not press on the cover.
Do not touch the connector with your fingertips.
Mishandling of the hard drive can result in permanent loss of data. Make a
backup copy of the drive s content before you remove it.
Apply care when handling the hard disk.
Note:
Certain models that come with the IBM-brand hard drive emit a clattering
sound when it is being rattled. This is a normal condition.
4-2
■ chapter 4 upgrading your computer
Upgrading the Hard Disk Drive
To replace the hard disk drive, do the following:
1. Turn OFF the computer. Unhook the AC cord and all
cables/devices attached to the notebook. Remove the battery.
2. Place your hand on a large metal object momentarily to
discharge any static electricity.
3. Locate and remove 7 Screw A’s.
4. Remove the System Device Cover.
4-3
■ chapter 4 upgrading your computer
5. Locate and remove 1 Screw B.
4-4
6. Push the HDD module to the right and separate it from
the connector. Lift the module away from the bay.
7. Locate and remove 4 Screw C’s from the HDD module.
■ chapter 4 upgrading your computer
Remove the metal case.
8. Re-attach the metal cover to the new hard drive and
tighten 4 Screw C’s.
9. Re-attach the HDD module to the HDD connector. And
re-attach Screw B.
10. Put the System Device Cover back and re-attach 7
Screw A ’s.
4-5
■ chapter 4 upgrading your computer
Congratulations! You have now completed the hard drive
upgrade. When you boot up the PC, you may need to create a
primary HDD partition and reformat the new drive and re-install
O/S, drivers, and all the necessary applications.
4-6
■ chapter 4 upgrading your computer
Upgrading the System Memory
Many applications will generally run faster when the computer’s
dynamic memory capacity is increased. The computer provides two
DDR2 memory sockets. There is one located underneath the
System Device Cover and another one located underneath the
keyboard. You can increase the amount of memory by replacing the
existing one with a dual inline memory module (commonly known
as SO-DIMM) of a higher capacity. The SO-DIMM can be 256MB,
512MB, or 1024MB in capacity. The SO-DIMM is of type DDR2
SDRAM, has 200 pins and runs on 1.8V.
Warning:
instructions carefully or have a qualified technician install it for you. Damages due to
mishandling of this procedure are NOT covered by the manufacture’s warranty.
Memory upgrade is a delicate process. Please observe the following
Warning:
mode may cause permanent damage to the hardware. Make sure you turn off the
power and unplug the AC cord before proceeding with a memory upgrade.
Changing memory while your computer is in suspend or power-saving
Warning:
or the manufacturer; otherwise the system may become unstable.
You should only use the DIMM module that is approved by the reseller
4-7
■ chapter 4 upgrading your computer
Installing a memory module (DIMM) into the system
To install the DIMM under the System Device Cover, do the
following:
1. Power OFF the notebook. Unplug the AC cord and all
cables/devices attached to the notebook. Remove the battery.
2. Place your hand on a large metal object momentarily to
discharge any static electricity. Place the notebook on a flat
surface and fully close the LCD lid.
3. Locate and remove 7 Screw A’s on the System Device
Cover.
4-8
4. Remove the System Device Cover. The DIMM socket is
now seen as shown below.
■ chapter 4 upgrading your computer
5. If you need to remove an old DIMM from the socket,
press out on the latches located on both edges of the socket at
the same time. The DIMM should pop up to an angle of 30
degree (see diagram below). Pull the DIMM module out of the
memory socket. Store away the DIMM for the future use.
6. Install the new DIMM module into the memory socket.
The DIMM will only fit in one orientation. Insert the DIMM at an
angle of approximately 30 degrees into the empty memory
socket. Then press it firmly so that the contact edge is driven
into the receiving socket.
4-9
■ chapter 4 upgrading your computer
7. Pivot the DIMM until the latches on both sides of the
socket snap into place.
Note:
Notice the notch on the DIMM. The notches should fit nicely with the
socket.
8. Put the System Device Cover back and tighten 7 Screw
A’s.
4-10
■ chapter 4 upgrading your computer
To install the DIMM under the keyboard, do the following:
1. Remove Screw D.
2. Find the keyboard latches near the edges of the
keyboard. The latch is spring-loaded. It will retract when
pressed and revert back to its original position when released.
Use a small blade to press the latch inward. The keyboard tray
should pop up slightly over the latch. If the keyboard tray does
not pop up, try to gently lift it up slightly above the latch. Repeat
this step for the other keyboard latches.
4-11
■ chapter 4 upgrading your computer
3. Carefully lift up the top edge and position the keyboard
out of the way and the following is revealed.
4-12
4. Carefully remove the Metal Cover and the DDR Socket is
■ chapter 4 upgrading your computer
shown. See the illustration below.
5. If you need to remove an old DIMM from the socket,
press out on the latches located on both edges of the socket at
the same time. The DIMM should pop up to an angle of 30
degree (see diagram below). Pull the DIMM module out of the
memory socket. Store away the DIMM for the future use.
6. Install the new DIMM module into the memory socket.
The DIMM will only fit in one orientation. Insert the DIMM at an
4-13
■ chapter 4 upgrading your computer
angle of approximately 30 degrees into the empty memory
socket. Then press it firmly so that the contact edge is driven
into the receiving socket.
7. Pivot the DIMM until the latches on both sides of the
socket snap into place.
Note:
Notice the notch on the DIMM. The notches should fit nicely with the
socket.
8. Put the Metal Cover back. Put the keyboard back to its
original position. Make sure the edge of the keyboard now
resides under the spring-loaded latches.
4-14
■ chapter 4 upgrading your computer
9. Re-attached Screw D.
Congratulations! You have just completed the memory upgrade.
When you boot up the computer , you should expect to see an
increase in DRAM capacity.
Your computer has been tested with a wide range of DIMM on the
Note:
market. However, not all memory modules are compatible. Check with your
system vendor for a list of compatible DIMM for your computer.
4-15
■ chapter 4 upgrading your computer
Adding the Mini-Card Type Wireless LAN Card
(Optional Device)
Your computer comes with a unique Mini-Card socket, which is
located underneath the System Device Cover . The socket allows
the computer to add unique features such as wireless LAN
(IEEE802.11x). Ask your dealer on the av ailability of the mini-card.
Warning:
instructions carefully or have a qualified technician install it for you. Damages due to
mishandling of this procedure are NOT covered by the manufacture’s warranty.
Warning:
power-saving mode may cause permanent damage to the hardware. Make sure you
turn off the power and unplug the AC cord before proceeding with the card upgrade.
Installing a mini-card is a delicate process. Please observe the following
Installing the mini-card while your computer is in suspend or
4-16
■ chapter 4 upgrading your computer
Installing the Mini-Card into the System
To install a new Mini-card, do the following:
1. Follow steps in the previous section, Installing a memory
module (DIMM) into the system, to access the Mini-Card
Socket underneath the System Device Cover.
2. The mini-card will only fit in one direction. Align the small
notch in the module with the socket on the connector and insert
the card at an angle of approximately 30 degrees into the
empty socket. Then press it firmly so that the contact edge is
driven into the receiving socket. Pivot the mini-card and fasten
2 Screw-F’s to hold the card down.
Note:
If you want to remove the mini-card from the socket, remove 2
Screw-F’s. The card should pop up to an angle of 30 degree.
3. Locate 2 antenna cables with connectors. Snap the cable
4-17
■ chapter 4 upgrading your computer
onto the golden connector on the wirelss mini-card. (Note: The
connectors are fairly small! This may take some maneuvering.
You may want to connect the antenna cables before inserting
the wireless card into the socket. )
4. Replace the System Device Cover and 7 Screw A’s.
Congratulations! You have now completed the wireless
mini-card installation. During the next time the system boots to
Windows, the system will prompt for driver location. Insert the
Factory CD-ROM and point to the directory where the Wireless
LAN driver can be found. In addition to installing the driver, you
may also need to run a Setup.exe program to install the card’ s
utility applications before it is fully operational.
4-18
■ chapter 4 upgrading your computer
Adding the DVB-T Module (Optional Device)
This section explains how to install the optional DVB-T Module to
your computer.
Warning:
following instructions carefully or have a qualified technician install it for you.
Damages due to mishandling of this procedure are NOT covered by the
manufacture’s warranty.
Warning:
power-saving mode may cause permanent damage to the hardware. Make sure you
turn off the power and unplug the AC cord before proceeding with the upgrade.
Installing the DVB-T Module is a delicate process. Please observe the
Installing the DVB-T Module while your computer is in suspend or
4-19
■ chapter 4 upgrading your computer
Installing the DVB-T Module into the System
To install a new DVB-T Module, do the following:
1. Power OFF the notebook. Unplug the AC cord and all
cables/devices attached to the notebook. Remove the battery.
2. Place your hand on a large metal object momentarily to
discharge any static electricity. Place the notebook on a flat
surface and fully close the LCD lid.
3. Remove Screw G and remove the DVB-T Device Cover.
4-20
4. The DVB-T Module will only fit in one direction. Align the
small notch in the module with the socket on the connector and
insert the card at an angle of approximately 30 degrees into the
empty socket. Then press it firmly so that the contact edge is
driven into the receiving socket. Pivot the mini-card and fasten
2 Screw-H’s to hold the card down.
Note:
If you want to remove the DVB-T Module from the socket, remove 2
Screw-H’s. The card should pop up to an angle of 30 degree.
■ chapter 4 upgrading your computer
5. Locate the antenna cable with connector. Snap the cable
onto the golden connector on the DVB-T Module. (Note: The
connector is fairly small! This may take some maneuvering.
You may want to connect the antenna cables before inserting
the card into the socket.)
6. Replace the DVB-T Device Cover and re-attach Screw G.
7. Connect the Antenna to DVB-T Antenna Connector on
the left side of the computer.
Note:
You also need to install the NewSoft Presto!PVR application from the
CD to watch and record TV programs.
4-21
■ chapter 5 trouble shooting
CHAPTER▼ FIVE
TROUBLE SHOOTING
In this chapter, you will learn how to
solve common hardware and software
problems.
5-1
■ chapter 5 trouble shooting
Your computer has been fully tested and complies with the
system specifications before shipping. However, incorrect
operations and/or mishandling may cause problems.
This chapter provides a reference for identifying and correcting
common hardware and software problems that you may encounter.
When you encounter a problem, you should first try to go through
the recommendations in this chapter. Instead of returning the
computer and waiting for repair, you may easily solve the problems
by considering the following scenarios and possible solutions. If the
error continues, contact your reseller for service information.
Before taking further actions, consider the following
suggestions:
Check to see if the problem persists when all the external
devices are removed.
Check to see that the green light indicator on the AC adapter
is lit.
Check to see the power cord is properly plugged to the wall
outlet and to the computer.
Check to see the power indicator of the compute r is on .
Check to see if your keyboard is operati onal by pressing and
holding any key.
Check for any incorrect or loose cable connections. Make
sure the latches on the connectors latch securely on to the receptor
end.
Be sure you have not performed an incorrect setting on the
5-2
■ chapter 5 trouble shooting
hardware devices in the BIOS Setup utility. A faulty setting may
cause the system to misbehave. If you are not sure of the changes
you made, try to restore all the settings to factory defaults.
Be sure all the device drivers are installed properly. For
example, without the audio driver properly installed, the speakers
and microphone will not work.
If external devices such as USB camera, scanner, printer do
not function correctly when connected to the system, it is usually
the device’s own problem. Consult the device’s manufacturer first.
Some software programs, which have not gone through
rigorous coding and testing, may cause problems during your
routine use. Consult the software vendor for problem solving.
Legacy peripheral are not plug-and -play capable. You need
to restart the system with these devices powered up and connected
first.
Be sure to go to BIOS SETUP and load DEFAULT SETTING
after BIOS re-flash.
Be sure the Quick Key Lockout Switch on the bottom of the
computer is not engaged; otherwise the quick keys will not work.
5-3
■ chapter 5 trouble shooting
Audio Problems
No speaker output -
Software volume control is turned down in Microsoft
Sound System or is muted. Double-click the speaker icon on
the lower right corner of the taskbar to see if the speaker has
been muted or turned down all the way.
Most audio problems are software-related. If your
computer worked before, chances are software may have been
set incorrectly.
Go to [Start > Settings > Control Panel] and double-click
the Sounds and Audio Devices icon. In the Audio page, make
sure that Realtek HD Audio is the default playback device.
Sound cannot be recorded -
You will need to plug-in an external microphone to the
microphone connector to record sound.
Double-click the speaker icon on the lower right corner of
the taskbar to see if the microphone has been muted.
1. Click Options and select Properties.
2. Select Recording and click the OK button.
3. After Click OK button, the recording volume control panel
will appear.
Go to [Start > Settings > Control Panel] and double-click
the Multimedia icon (or Sounds and Audio Devices icon). In the
Volume or Audio page, make sure that Realtek HD Audio is the
default recording device.
5-4
■ chapter 5 trouble shooting
Hard Disk Problems
The hard disk drive does not work or is not recognizable -
If you had just performed a hard disk upgrade, make sure
the hard drive connector is not loose and the hard disk drive is
also correctly seated. Remove it and reinsert it firmly, and
restart your PC. (Refer to Chapter 4 for details.)
The new HDD may need to be partitioned and
reformatted. O/S and drivers will need to be re-installed as well.
Check the hard disk indicator LED. When you access a
file, the LED lamp should light up momentarily.
The new HDD may be defective or is not compatible.
If your computer has been subjected to static electricity
or physical shock, you may have damaged the disk drive.
The hard drive is making abnormal whining noises -
You should back up your files as soon as possible.
Make sure the source of noise is indeed from the hard
drive and not the fan or other devices.
The hard disk drive has reached its capacity -
Run Disk Cleanup utility in Windows. [Start > All
Programs > Accessories > System Tools > Disk Cleanup] The
system will prompt you for what to do.
Archive files or programs that you had no longer used by
moving them to an alternative storage medium (floppy disk,
optical record-able disk, etc.) or uninstall programs that no
longer use.
Many browsers store files in the hard drive as a cache to
speed up the performance. Check the program’s Online Help
5-5
■ chapter 5 trouble shooting
for instructions on decreasing the cache size or on removing
temporary Internet files.
Empty the Recycle Bin to create more disk space. When
you delete files, Windows saves them to the Recycle Bin.
The hard disk takes longer to read a file -
If you have been using the drive for a period, the files
may be fragmented. Go to [Start > Programs > Acce ssories >
System Tools > Disk Defragmenter] to perform a disk
defragmentation. This operation may take a while.
Interrupt request s or p roblems with other hardware
devices may have occupied the CPU and therefore slows down
the system performance.
The files are corrupted -
Run the Error-checking utility in Windows to check the
HDD. Double-click My Computer . Right -cli ck C: and select
Properties. Click Check Now in Error- checking in Tools.
5-6
■ chapter 5 trouble shooting
Optical Drive Problems
The optical drive does not work -
Try rebooting the system.
The disk is damaged or files are not readable.
After you have inserted a CD-ROM di sk, it may take a
moment before you can access its content.
The drive dose not read any disks -
The CD may not be properly seated in the tray. Make
sure the disk is firmly seated onto the spindle.
The disk is damaged or not readable.
The disk cannot be ejected -
Normally, it takes a few seconds to eject the disk.
If the disk cannot be ejected, it may be mechanically
jammed. Straighten out a paper clip and insert it to a tiny hole
next to the eject button. This should reject the disk tray. If not,
return the unit for repair. Do not forcefully pull on the disk tray.
The Combo or DVD Dual or Supermulti drive (optional
device) cannot record -
You need to purchase and install a burner utility program
to record files to a blank media.
5-7
■ chapter 5 trouble shooting
Display Problems
The display panel is blank when the system is turned on -
Make sure the computer is not in the Standby or
Hibernate suspend modes. The display is turned off to
conserve energy in these modes.
The screen is difficult to read -
The display resolution should at least be set to at
least1024x768 for optimal viewing.
1. Go to [Start > Settings > Control Panel] and double-click
the Display icon.
2. Under the Settings page, set screen resolution to at least
1024x768 and choose at least 256 colors.
The screen flickers -
It is normal if the display flickers a few times during
shutting down or powering up.
5-8
■ chapter 5 trouble shooting
Keyboard and Mouse Problems
The built-in touch pad performs erratically -
Make sure there is no excess perspirati on or humidity on
your hand when using the touch pad. Keep the surface of the
touch pad clean and dry.
Do not rest your palm or wrist on the surface of the touch
pad while typing or using the touch pad.
The built-in keyboard accepts no input -
If you are connecting an external keyboard to the system,
the built-in keyboard may not work.
Try restarting the system.
The characters on the screen repeat while I type.
You may be holding the keys down too long while you’re
typing.
Keep the keyboard clean. Dust and dirt under the keys
could cause them to stick.
Configure the keyboard to wait longer before the auto
repeat feature starts. To adjust this feature, Go to [Start >
Settings > Control Panel], and double-click the Keyboard icon.
A dialogue bo x shows up with the adjustable settings for the
keyboard.
5-9
■ chapter 5 trouble shooting
CMOS Battery Problem
A message “CMOS Checksum Failure” displays during the
booting process or the time (clock) resets when booting -
Try to reboot the system.
If the message “CMOS Checksum Failure” a ppears
during the booting procedure even after rebooting, it may
indicate failure of the CMOS battery. If so, you need to replace
the battery. This battery normally lasts two to five years. The
battery is of type CR2032 (3V). You may replace it by yourself.
The battery is located under the System Device Cover on the
bottom of the notebook. See Chapter 4 for more details.
5-10
■ chapter 5 trouble shooting
Memory Problems
The POST does not show an increased memory capacity
when you have already installed additional memory -
Certain brands of memory module m ay not be
compatible with your system. You should ask your vendor for a
list of compatible DIMM.
The memory module may not be inst alled properly. Go
back to Chapter 4 to review the details of this operation.
The memory module may be defective.
The O/S issues an insufficient memory error message
during operation -
This is often a software or Windows-related problem. A
program is draining the memory resources.
Close the application programs you’re not using and
restart the system.
You need to install additional memory module. For
instructions, go to Chapter 4 Upgrading Your Computer.
5-11
■ chapter 5 trouble shooting
Modem Problems
The built-in modem does not respond -
Make sure the modem driver is loaded p rope rly.
Go to [Start > Settings > Control Panel > Phone and
Modem Options] and go to Modems tab. Make sure Motorola
SM56 Data Fax Modem is listed. Otherwise, click the Add
button to add the modem drive, which is located in the factory
CD-ROM (or floppy diskette).
Go to [Start > Settings > Control Panel > System] and
click Device Manager button in the Hardware page to check for
possible resource or driver conflict. See Windows on-line help
or manual for how to handle such problems.
Make sure the phone line, which the co mputer is
connected to, is working.
Connection difficulties -
Be sure to disable Call W aiting on the phone line.
Be sure to have the correct country setting where your
computer is used. Go to [Start > Settings > Control Panel >
Phone and Modem Options]. Go to Dialing Rules and Edit My
Location. In the Country/Region pull-down menu, select the
appropriate country setting.
Excessive line noise might cause the connection to be
dropped. To check this, put the regular phone handset on the
line and placing a phone call. If you do hear abnormal noise, try
to make the modem connection with a different line or contact
your local telephony company for service.
Make sure the cable connection is firm.
Try a different receiver number and see if the problem
persists.
5-12
■ chapter 5 trouble shooting
Network Adapter / Ethernet Problems
The Ethernet adapter does not work -
Go to [Start > Settings > Control Panel > System >
Hardware > Device Manager]. Double-click on Network
Adapters and check if Generic Marvell Yukon Chipset based
Gigabit Ethernet Controller appears as one of the adapters. If it
does not exist, Windows has not detected the Generic Marvell
Yukon Chi pset based Gigabit Ethernet Controller or the device
driver has not been installed properly. If there is a yellow mark
or red-cross on the network adapter, it may be a device or
resource conflict. Replace or update the device driver from the
factory CD-ROM disk or consult Windows manual on how to
solve the resource conflict problem.
Make sure the physical connections on both ends of the
cable are good.
The hub or concentrator may not be working properly.
Check to see if other workstations connected to the same hub
or concentrator is working.
The Ethernet adapter does not appear to operate in the
1000Mbps transmission mode -
Make sure the hub you are using supports 1000Mbps
operation.
Make sure that your RJ-45 cable meets the
1000Base-TX requirements.
Make sure the Ethernet cable is connected to the hub
socket that supports 1000Base-TX mode. The hub may have
both 100Base-TX and 1000Base-T sockets.
5-13
■ chapter 5 trouble shooting
Performance Problems
The computer becomes hot -
In a 35
computer’s back case are expected to reach 50 degrees.
Make sure the air vents are not blocked.
If the fan does not seem to be working at high
temperature (50 degrees Celsius and up), contact the service
center.
Certain programs that are processor-int ensive may
increase the computer temperature to a degree where the
computer automatically slows down its CPU clock to protect
itself from thermal damage.
The program appears stopped or runs very slowly -
Press CTRL+ALT+DEL to see if an application is still
responding.
Restart the computer.
This may be normal for Windows when it is processing
other CPU-intensive programs in the background or when the
system is accessing slow-speed devices such the floppy disk
drive.
You may be running too many applications. Try to close
some applications or increase system memory for higher
performance.
The processor may have been overheated due to the
system’s inability to regulate its internal heat. Make sure the
computer’s ventilation grills are not blocked.
o
C environment, the certain areas of the
5-14
■ chapter 5 trouble shooting
Firewire (IEEE1394) and USB2.0 Problems
The USB device does not work -
Windows NT 4.0 does not support USB protocols
Check the settings in the Windows Control Panel.
Make sure you have installed the necessary device
drivers.
Contact the device vendor for additional support.
The IEEE1394 port does not work -
Go to [Start > Settings > Control Panel > System >
Hardware > Device Manager]. You should see an entry which
reads “OHCI Compliant IEEE 1394 Host Controllers”. If it does
not exist, Windows has not detected the host controller or the
device driver has not been installed properly. If there is a yellow
mark or red-cross on the 1394 host controller, it may be a
device or resource conflict. Replace or update the device driver
from the factory CD-ROM disk or consult Windows manual on
how to solve the resource conflict problem.
Make sure the cable is fully connected.
Make sure you have installed the necessary device
drivers.
Contact the device vendor for additional support.
5-15
■ appendix A product specification
A
APPENDIX▼ A
PRODUCT SPECIFICATION
-1
■ appendix A product specification
A
▼ Processor and Core Logic
Processor
Core Logic
z Mobile Intel Pentium M Duo Dual-Core Processor
(Yonah), up to 2.16GHz, 2 MB L2 cache or
z Mobile Intel Pentium M Solo Single-Core
Processor (Yonah), up to 1.66GHz, 2MB L2
cache
Intel Calistoga 945GM + ICH7-M chipset with audio,
modem, and USB2.0 controllers integrated
667MHz Front Side Bus
533 / 667MHz DDR2 interface
▼
System Memory
Memory Type
Default
Memory
Expansion
DDR2 SDRAM 533 / 667
256 / 512 / 1024MB
Two 200-pin DIMM sockets, Max 2 GB
▼
Display
LCD Panel
Graphic
Accelerator
Motion
Playback
Other
Features
14.1-inch Wide-Viewing-Angle WXGA TFT LCD
Intel Integrated GMA950 Graphic Engine
Hardware Motion Compensation and IDCT Supported
for MPEG1/2 Playback
DirectX compatible
-2
■ appendix A product specification
A
▼ Audio
Chipset
Audio Codec
Sound
Capabilities
Chipset
Transmission
Rate
Module
Transmission
Protocol
Chipset
PnP Function
Flow Control
Speed
Selection
Other
Features
Intel (ICH7M) integrated audio controller
Realtek Audio Codec
DirectSound 3D, EAX 1.0 & 2.0 compatible
A3D, I3DL2 compatible
AC97 V2.3 compatible
Azalia compatible
2 Stereo Speakers
▼
Modem (Optional)
Intel ICH7-M integrated Modem Controller with MDC
card, support 56K MDC Modem Card with Azalia
standard
V.92 / V.90 / K56flex for download data speed up to
56Kbps.
V.34, V.17, V.29 protocol supported
▼
Wireless LAN
Intel PRO/Wireless 3945ABG Card
Mini-Card Interface IEEE802.11 B&G
▼
LAN / Ethernet
Marvell Ethernet function for 10/100/1000Base-TX
network standards
Windows XP Plug and Play compatible
Automatic Jam and auto-negotiation for flow control
Auto Negotiation and Parallel detection for automatic
speed selection (IEEE 802.3u)
High performance 32-bit PCI bus master architecture
with integrated DMA controller for low CPU and bus
utilization
Remote Wake-up Scheme supported
Hot Insertion supported
-3
■ appendix A product specification
A
▼ Firewire IEEE1394(a)
Chipset
Capabilities
Hard Drive
Combo Drive
DVD-Dual or
Super-Multi
Standards
Keyboard
Touch pad
02 Micro 0Z128 IEEE1394 OHCI Host Controller
Up to 400 Mbps
Expandable up to 63 devices in chains
▼
Storage
S-ATA 2.5-inch format hard disk drive
5.25-inch format (12.7mm height) fixed module
(Optional Purchase)
5.25-inch format (12.7mm height) fixed module
(Optional Purchase)
▼
Keyboard & Touch pad
86/87-key QWERTY keyboard with numeric keypad
and Windows keys, 19.05mm Pitch
Built-in Touch Pad
▼
ExpressCard (NewCard) & Multiple
Card Reader
Chipset
Express Card /
New Card
4-in-1 Card
Reader Format
Support
02 Micro 0Z128 (Card Reader)
Single Slot, 34mm type I supported
Multimedia Card (MMC), Secure Digital Card (SD),
Memory Stick (MS), and MS Pro Card
-4
Loading...