e-Line Technology ELI-IP5-B5-49MR User Manual

5MP IP Network Camera User’s Manual

ELI-IP5-B5-49MR

IP

5

Network

800.683.6835

MP

Resolution

yr

2

Warranty

Motion
Activated
Recording

Free

Tech-Support

eLineTechnology.com

i

Welcome

Thank you for purchasing our network camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

ii

Important Safeguards and Warnings

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1. (Refer to general introduction) Please

note: Do not connect two power supplying sources to the device at the same time; it may result
in device damage! The product must be grounded to reduce the risk of electronic shock.

We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Transportation security

Heavy stress, violent vibration or water splash are not allowed during transportation, storage and
installation.

3．Installation

Do not apply power to the camera before completing installation.
Please install the proper power cut-off device during the installation connection.
Always follow the instruction guide the manufacturer recommended.

4．Qualified engineers needed

All the examination and repair work should be done by the qualified service engineers.
We are not liable for any problems caused by unauthorized modifications or attempted repair.

5．Environment

This series network camera should be installed in a cool, dry place away from direct sunlight,
inflammable, explosive substances and etc.
Please keep it away from the electromagnetic radiation object and environment.
Please make sure the CCD (CMOS) component is out of the radiation of the laser beam device.
Otherwise it may result in CCD (CMOS) optical component damage.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the camera.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.

6. Daily Maintenance

Please shut down the device and then unplug the power cable before you begin daily maintenance
work.

iii

Do not touch the CCD (CMOS) optic component. You can use the blower to clean the dust on the lens
surface.
Always use the dry soft cloth to clean the device. If there is too much dust, please use the water to
dilute the mild detergent first and then use it to clean the device. Finally use the dry cloth to clean the
device.
Please put the dustproof cap to protect the CCD (CMOS) component when you do not use the camera.
Dome enclosure is the optical component, do not touch the enclosure when you are installing the
device or clean the enclosure when you are doing maintenance work. Please use professional optical
clean method to clean the enclosure. Improper enclosure clean method (such as use cloth) may result
in poor IR effect of camera with IR function.

7. Accessories

Be sure to use all the accessories recommended by manufacturer.
Before installation, please open the package and check all the components are included.
Contact your local retailer ASAP if something is broken in your package.

Accessory Name

Amount

Network Camera Unit

1

Quick Start Guide

1

Installation Accessories Bag

1

12V to 24V Conversion Cable
(For AC 24V series product only)

1

CD

1

iv

Table of Contents

1 General Introduction ...................................................................................................... 1

1.1 Overview ........................................................................................................... 1

1.2 Features ............................................................................................................ 1

1.3 Specifications (ELI-IP5-B5-49MR)..........................................................2

1.3.1 Performance ............................................................................................... 2

2 Framework ..................................................................................................................... 4

2.1 Multiple-function Combination Cable................................................................. 8

2.2 Framework and Dimension ............................................................................... 9

2.3 Bidirectional talk .............................................................................................. 10

2.3.1 Device-end to PC-end............................................................................... 10

2.3.2 PC-end to the device-end ......................................................................... 10

2.4 Alarm Setup .................................................................................................... 10

3 Device Installation ....................................................................................................... 12

3.1 Device Installation ........................................................................................... 12

3.2 Install Micro SD Card ...................................................................................... 12

3.3 Adjust Lens ..................................................................................................... 13

3.4 Adjust Bracket ................................................................................................. 14

3.5 Button .............................................................................................................. 15

4 Quick Configuration Tool ............................................................................................. 17

4.1 Overview ......................................................................................................... 17

v

4.2 Operation ........................................................................................................ 17

5 Web Operation ............................................................................................................ 19

5.1 Network Connection ........................................................................................ 19

5.2 Login and Main Interface ................................................................................. 19

6 FAQ ............................................................................................................................. 21

Appendix Toxic or Hazardous Materials or Elements ........................................................ 22

1

1 General Introduction

1.1 Overview

This series network camera integrates the traditional camera and network video technology. It adopts
audio and video data collection, transmission together. It can connect to the network directly without
any auxiliary device.

This series network camera uses standard H.264 video compression technology and G.711a audio
compression technology, which maximally guarantee the audio and video quality.

It supports the IR night vision function. In the night environments, the device can use the IR light to
highlight the object which is suitable for the surveillance function in the low illumination environments.
The built-in protection enclosure and waterproof design conforms to the IP 66 level. It has the sound
waterproof function suitable for use in the outdoor environments.

It supports real-time monitor and listening at the same time. It supports analog video output and dual­way bidirectional talk.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its multiple functions and various uses, this series
network camera is widely used in many environments such office, bank, road monitor and etc.

Assistant

Function

 Log function
 Support system resource information and running status real-time display.
 Day/Night mode auto switch.
 Built-in IR light. Support IR night vision.
 Support picture parameter setup such as electronic shutter and gain setup.
 Backlight compensation: screen auto split to realize backlight compensation

to adjust the bright.

 Support video watermark function to avoid vicious video modification.
 The enclosure conforms to the IP 66 protection. Has the waterproof function.

1.3 Specifications

1.3.1 Performance

Please refer to the following sheet for network camera performance specification.

6

Model

Parameter

ELI-IP5-B5-49MR

System

Main Processor

High performance DSP

OS

Embedded LINUX

System
Resources

Support real-time network monitoring, local record, and remote
operation at the same time.

User Interface

Remote operation interface such as WEB, DSS, PSS

System Status

Micro SD card status info, bit stream statistics, log, and software
version.

Video Parameter

Image Sensor

1/2.5-inch CMOS

Pixel

2560(H)*1920(V)

Day/Night Mode

Support day/night mode switch and IR-CUT at the same time.
(embedded IR-CUT)

Auto Aperture

Enable

Gain Control

Fixed/Auto

White Balance

Manual/Auto

BLC

Off/BLC(default or custom)/WDR (0-100 adjustable)/HLC(0-100
adjustable)

Exposure Mode

Manual/Auto
It ranges from 1/3 to 1/100000)

Video
Compression
Standard

H.264/H.264H/MJPEG

Video Frame
Rate

PAL:
Main stream (2560*1920@12fps)
Extra stream 1 (704*756@12fps,
Extra stream 2 (1280*720@9fps);
Main stream (1920*1080@25fps)
Extra stream 1 (704*576@25fps,
Extra stream 2 (1280* 720@11fps)

NTSC:
Main stream (2560*1920@12fps)
Extra stream 1 (704*480@12fps,
Extra stream 2 (1280*720@10fps);
Main stream (1920*1080@30fps)
Extra stream 1 (704*480@30fps,

Extra stream 2 (1280* 720@1fps)

Note:
The exact frame rate of extra stream 2 is decided by the device max
capacity set, and it is dynamic and adjustable during the range of
capacity set.

Video Bit Rate

H.264H: 40-8192Kbps, adjustable
MJPEG:40-16384kbps, adjustable and bit rate is adjustable.
Support customized setup.

Video Flip

Support mirror, flip and rotation mode function.

Snapshot

Max 1f/s snapshot. File extension name is JPEG.

Privacy Mask

Supports max 4 privacy mask zones

Video Setup

Support parameter setup such as bright, contrast.

Video
Information

Channel title, time title, motion detect, tampering, overlay.

Lens

Motorized 3~9mm@F1.4 (subject to actual product)

Lens Interface

Φ14. Lens is the default accessories

7

Audio

Audio Input

1-channel,RCA

Audio Output

1-channel, RCA

Bidirectional
Talk Input

Reuse the first audio input channel

Audio Bit Rate

8kbps 16bit/16kbps 16bit

Audio
Compression
Standard

G.711A/G.711Mu

Video

Motion Detect

396 (18*22) detection zones; sensitivity level ranges from 0 to 100;
area threshold ranges from 0 to 100.
Activation event: alarm device, audio and video storage, image
snapshot, log, email function and etc.

Alarm Port

2-channel input,1-channel output

Record

and

Backup

Record Priority

Manual>External alarm >Video detect>Schedule

Storage
Management

Support Micro SD card (64G) disconnection local storage, NAS
storage.

Network

Wire Network

1-channel wire Ethernet port, 10/100 Base-T Ethernet

Network Protocol

HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP,UDP, RTCP, SMTP,
FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP, QoS,

802.1x

Protocol

PSIA, ONVIF

Remote
Operation

Monitor, system setup, file download, log information, maintenance ,
upgrade and etc

AUX

Interface

Video Output

1-channel analog video output,BNC port

Reset

Reset button

General Parameter

Power

AC 24V/PoE or DC 12V/PoE (optional), can’t be supported at the same
time.

Power
Consumption

9W MAX (-H series≤11.5W, PoE (AT standard))

Working
Temperature

-30℃~+60℃(-H series: -40℃～+60℃)

Working
Humidify

≤95%

Dimensions(mm)

φ104×306.7

Weight

1250g(Excluding box)

Installation

Bracket is included as default.

IR Distance

20~30m

Protection Level

IP66

Note

Model with “-H” means it has electrical heating, otherwise, it does not
have. (Subject to actual product)

8

2 Framework

2.1 Multiple-function Combination Cable

You can refer to the following figure for multiple-function combination cable information. See Figure
2-1.

Figure 2-1 Multiple-function combination cable

Please refer to the following sheet for detailed information.

SN

Port Name

Function

Connection

Note

1
DC12V/AC24V

Power input
port

/

Power port. Input DC 12V or AC 24V.
(convertor is required)

Note:
Please refer to actual device label.

2

RESET

Reset button

/

The reset button is to restore device factory
default setup. Press 3~5 seconds.

3

I/O

I/O cable
port

/

Includes alarm input and output.

4

LAN

Network port

Ethernet
port

 Connect to standard Ethernet cable.

5

AUDIO IN

Audio input
port

RCA

Input audio signal. It can receive the
analog audio signal from the pickup.

6

AUDIO OUT

Audio output
port

RCA

Output audio signal to the devices such as
the sound box.

7

VIDEO OUT

Video output
port

BNC

Output analog video signal. It can connect
to the TV monitor to view the video.

Please refer to the follow sheet for detailed pin information.

9

Port Name

SN

Name

Note

I/O Port

1

ALARM_COM

Alarm output public port.

2

ALARM_NO

Alarm output port. It is to output the alarm signal to
the alarm device.

NO: normal open alarm output port.
It shall work with ALARM_COM port.

3

ALARM_IN1

Alarm input port 1. It is to receive the on-off signal
from the external alarm source.

4

ALARM_IN2

Alarm input port 2. It is to receive the on-off signal
from the external alarm source.

5

GND

Ground port

2.2 Framework and Dimension

Please refer to the following figure for dimension information. The unit is mm. See Figure 2-2 and
Figure 2-3.

Figure 2-2 Dimension illustration 1

Figure 2-3 Dimension illustration 2

10

2.3 Bidirectional talk

2.3.1 Device-end to PC-end
Device Connection

Please connect the speaker or the MIC to the audio input port of the device. Then connect the
earphone to the audio output port of the PC.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the bidirectional talk function.
Click Talk button again to stop the bidirectional talk function.

Listening Operation

At the device end, speak via the speaker or MIC, and then you can get the audio from the earphone or
sound box at the pc-end.

2.3.2 PC-end to the device-end
Device Connection

Connect the speaker or the MIC to the audio input port of the PC and then connect the earphone to
the audio output port of the device.
Login the Web and then click the Talk button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Talk button again to stop the bidirectional talk function.

Please note the on-site listening operation is null during the bidirectional talk process.

Listening Operation

At the PC-end, speak via the speaker or MIC, and then you can get the audio from the earphone or
sound box at the device-end.

2.4 Alarm Setup

The alarm interface is shown as in Figure 2-4. Please follow the steps listed below for local alarm input
and output connection.

1) Connect the alarm input device to the alarm input port (No.3 pin or No.4 pin) of the I/O cable.

2) Connect the alarm output device to the alarm output port (No.2 pin) and alarm output public port
(No.1 pin). The alarm output port supports NO (normal open) alarm device only.

3) Open the Web, go to the Figure 2-4. Please set the alarm input 01 port for the first channel of the
I/O cable (No.3 pin). The alarm input 02 is for the 2nd channel of I/O cable (No.4 pin). Then you can
select the corresponding type (NO/NC.)

4) Set the WEB alarm output. The alarm output 01 is for the alarm output port of the device. It is the
No.2 pin of the I/O cable.

11

Figure 2-4 Alarm

Please refer to the following figure for alarm input information. See Figure 2-5.
Alarm input: When the input signal is idle or grounded, the device can collect the different statuses of
the alarm input port. When the input signal is connected to the 5V or is idle, the device collects the
logic “1”. When the input signal is grounded, the device collects the logic “0”.

Figure 2-5 Alarm input

Please refer to the following figure for alarm output information. See Figure 2-6.
Port NO and Port C composes an on-off button to provide the alarm output.
If the type is NO, this button is normal open. The button becomes on when there is an alarm output.
If the type is NC, this button is normal off. The button becomes off when there is an alarm output.

Figure 2-6 Alarm output

12

3 Device Installation

3.1 Device Installation

Please follow the steps listed below to install the device. Please refer to Figure 3-1 for reference.

 Dig three holes in the wall or the surface, and then input the three expansion bolts to

the holes and secure.

 Put the three fixed holes of the bottom of the bracket to the three holes you just dug in

the wall or surface. Put the three fixed screws to the three holes of the bracket and
then secure firmly. Finally you can fix the bracket in the wall or surface.

Figure 3-1 Device installation illustration

3.2 Install Micro SD Card

Step 1. Rotate front cover counterclockwise and take it down, and you can see SD card clot.
Step 2. Insert Micro-SD card into SD card slot according to Figure 2-2.
Step 3. Put back front cover by clockwise rotating.
Note:
Please properly install Micro SD card, otherwise, may cause SD card error.
Please properly put back the front cover for waterproof purpose.

13

Figure 3-2 Micro-SD card

3.3 Adjust Lens

Rotate lens counterclockwise, and take it down. You can see its front and rear adjusting rod. Front rod
adjusts focus while rear rod adjusts zoom. After adjusting rod, rotate lens cover clockwise to fasten it.
See Figure 2-3.
Note:

 If you cannot rotate lens cover, you can take down sunshield first.
 Please properly put back the front cover for waterproof purpose.
 Motorized series device has default motorized lens which do not need manual adjustment.

14

Figure 3-3 Adjusting lens

3.4 Adjust Bracket

You adjust bracket with a M4 inner hex screw. Before adjustment, you loosen the screw with inner hex
wrench in accessories bag. Rotate rear cover 360°horizontally, and 90°vertically. Rotate pedestal
360°.
Secure the screw with inner hex wrench after adjustment. See Figure 2-4.
Note:
M4 inner hex wrench must be secured, otherwise the pedestal will be unstable and device cannot be
fixed to specific angle.

15

Figure 3-4 Adjusting bracket

3.5 Button

You can switch button to up/down to zoom in/out. You also can switch button to left/right to focus.
Long press button for 2s for auto focus which makes video clear. See Figure 2-5 and 2-6.

Note:
The button is for motorized series only.

16

Figure 3-5 Button Position

Figure 3-6 Button

17

4 Quick Configuration Tool

4.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you can
use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation

Double click the “ConfigTools.exe” icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.

Figure 4-1 Search interface

Select one IP address and then right click mouse, you can see an interface is shown as in Figure 4-2.
Select the “Open Device Web” item; you can go to the corresponding web login interface.

Figure 4-2 Search interface 2

If you want to modify the device IP address without logging in the device web interface, you can go to
the configuration tool main interface to set.

18

In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the Login
button to go to the login interface. See Figure 4-3.
In Figure 4-3, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in Web
Network interface. Otherwise, you cannot login the device.
If you are using device background upgrade port 3800 to login, other setups are all invalid.

Figure 4-3 Login prompt

After you logged in, the configuration tool main interface is shown as below. See Figure 4-4.

Figure 4-4 Main interface

For detailed information and operation instruction of the quick configuration tool, please refer
to the Quick Configuration Tool User’s Manual included in the resources CD.

19

5 Web Operation

This series network camera products support the Web access and management via PC.
Web includes several modules: Monitor channel preview, system configuration, alarm and etc.

5.1 Network Connection

Please follow the steps listed below for network connection.

 Make sure the network camera has connected to the network properly.
 Please set the IP address, subnet mask and gateway of the PC and the network camera

respectively. Network camera default IP address is 192.168.1.108. Subnet mask is 255.255.255.0.
Gateway is 192.168.1.1

 Use order ping ***.***.***.***(* network camera address) to check connection is OK or not.

5.2 Login and Main Interface

Open IE and input network camera address in the address bar. See Figure 5- 1.

Figure 5- 1 IP address

The login interface is shown as below. See Figure 5- 2.
Please input your user name and password.
Default factory name is admin and password is admin.

Note: For security reasons, please modify your password after you first login.

Input your IP
address here

20

Figure 5- 2 Web login

After you successfully logged in, please install WEB plug-in unit. Please refer to the Web Operation
Manual included in the resource CD for detailed operation instruction.
See Figure 5- 3.

Figure 5- 3 Web monitoring window

21

6 FAQ

Bug

I can not boot up
the device.

Please click RESET button for at least five seconds to restore
factory default setup.

Micro SD card
write times

Do not set the Micro SD card as the storage media to storage the
schedule record file. It may damage the Micro SD card duration.

I can not use the
disk as the storage
media.

When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).

I can not upgrade
the device via
network.

When network upgrade operation failed, you can use port 3800 to
continue upgrade.

Recommended
Micro SD card
brand

Support Micro SD card, we recommend 4GB or higher industry-level
high speed card.

Audio function

Please use active device for the audio monitor input, otherwise there
is no audio in the client-end.

To guarantee
setup update

After you modified the important setup, please reboot the device via
the software to make sure the setup has been updated to the
storage medium.

Power adapter

The general power adapter included in the accessories bag can
work ranging from 0℃ to 40 ℃. The device may result in unstable
power supply when the temperature exceeds the working
temperature.

Please replace an industry-level power adapter if you are using in
the harsh environments.

Rear bracket is not
stable

The rear bracket requires to be tightened with a S3 inner hex
wrench, and user shall manually check if it is fastened or not.

SD card reading
error

Re-plug in SD card, if it still does not work, the SD card may be
damaged.

22

Appendix Toxic or Hazardous Materials or Elements

Component

Name

Toxic or Hazardous Materials or Elements

Pb

Hg

Cd

Cr VI

PBB

PBDE

Circuit Board

Component

○ ○ ○ ○ ○

○

Device

Construction

Material

○ ○ ○ ○ ○

○

Wire and Cable

○ ○ ○ ○ ○ ○ Packing

Components

○ ○ ○ ○ ○

○

Accessories

○ ○ ○ ○ ○

○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in the
parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all homogeneous
materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard. During the
environmental-friendly use period (EFUP) period, the toxic or hazardous substance or elements
contained in products will not leak or mutate so that the use of these (substances or elements) will not
result in any severe environmental pollution, any bodily injury or damage to any assets. The consumer
is not authorized to process such kind of substances or elements, please return to the corresponding
local authorities to process according to your local government statutes。

Note

 This user’s manual is for reference only. Slight difference may be found in user interface.
 All the designs and software here are subject to change without prior written notice.
 If there is any uncertainty or controversy, please refer to the final explanation of us.
 Please visit our website for more information.

 All trademarks and registered trademarks are the properties of their respective owners.