eLine Technology EEOHT User Manual

BRIEF OF PRODUCT

* Sensor (CCD)

Adopt SONY 1/3" CCD Sensor. * Auto Gain Control (AGC)

Built-in auto gain control (AGC) circuit. The color camera can get high definition picture in low Lux condition.

* Scanning Mode NTSC or PAL mode.

* Water Resistance

IP66. * OSD SETTING

OSD

SET

Standard AE

SWDR Level :0~8, DWDR: On/Off

BLC Level : Auto/Low/Middle/High

mode

Color adjust

Image Adjust

Intelli-

System

setting

Infor-

mation

HLC Set range, Level : Low/Middle/High, Mask grayscale:1~6

Face AE Frame : Off/On ,Sensitivity : 0~11

Face

auto zoom

Demist Level : Auto/Low/Middle/High

CR suppress Off, On

Day & Night Off, On, Auto, Ext

Digital slow

shutter

detectoin

Motion

detection

gent

D-Zoom D-Zoom: 1~256, Tilt: -100~100, Pan: -100~100

Privacy mask

IR input level High/Low

Smart IR

control

Camera ID 0~255

Baud rate

AC Freq 50Hz, 60Hz

Language

Show ID/Icon show icon, show ID, show ID/Icon, Off

Version

information

Frame:Off/On, Sensitivity : 0~11, Warning trigger :High/Low/

AWB AWB,ATW,F/A,U30,CWF,D50,D65,D75

Brightness:0~99,Color-Red:0~99,Color-Green:0~99,Color-

Face

Lens Manual/DC-Indoor/DC-Outdoor

Blue:0~99,Contrast:0~99,Saturation:0~99

(1/60),1/100,1/250,1/500,1/2000,1/5000,1/10000,1/100000,1x

,2x,3x,4x,5x,6x,7x,8x,16x,32x,64x,128x,256x

3D-NR: 0~3, 2D-NR-1: 0~32, 2D-NR-2: 0~32, Sharpen:

0~32, FC-suppress: 0~15, Blemish compensation: 0~3

Switch: Off/On, Frame: Off/On, Sensitivity: 0~11, Warning

trigger: High/Low/Off, Warning seconds: 0~65535

Switch: Off/On, Set range, Sensitivity: -2~2, Warning trigger:

High/Low/Off, Warning seconds: 0~65535

Opacity: 0~3, Mask select :1~8, Set mask area, Switch: Off/

1200/2400/4800/9600/19200/38400/57600/115200/230400/

On, Mask color: 0~65535

English, Francais, Espanol,Pyccknn, Chinese

Off, Warning seconds

Auto,1/50,

Off/On

460800

CONNECTING

LEFT

KEY BOARD

DOWN

Monitor

RIGHT

PRESS

DC12V Power Supply

Link wire rule：

Video

Power

Video

DC12V

TROUBLE AND SOLUTION

1. No Picture after providing power

. May be the power supply voltage abnormity, please check the power supply voltage and pole whether exactitude. . Please check all the connecting cable and monitors whether be connected correctly or not.

2. The picture level direction have flowing interference ripples

. May be caused by the power supply AC ripples, it need filter the wave of the power supply. . Check the monitor and peripheral equipments used.

3. The picture background color changes continuously

. The fluorescent lamp’s electromagnetic field cause color roll. This is proper phenomenon of the cameras. . Reduce the fluorescent lamp numbers or increase the distance between the camera and the fluorescent lamps can improve it. . Use power supply external sync. camera can solve it.

4. The picture smear too mass

. The power supply’s voltage unstable. . Connecting cables not connect correctly or have high impedance.