eLine Technology DFB User Manual

eLineTechnology.com

Megapixel Indoor IP Camera User’s Manual

Version 3.5.0

Welcome

eLineTechnology.com

Thank you for purchasing our IP camera!
This user’s manual is designed to be a reference tool for your system.
Please read the following safeguard and warnings carefully before you use this series product!
Please keep this user’s manual well for future reference!

i

Important Safeguards and Warnings

eLineTechnology.com

1．Electrical safety

All installation and operation here should conform to your local electrical safety codes.
The power shall conform to the requirement in the SELV (Safety Extra Low Voltage) and the Limited
power source is rated 12V DC or 24V AC in the IEC60950-1.
Before you replace the SD card, please unplug the power cable and then remove the shell
We assume no liability or responsibility for all the fires or electrical shock caused by improper handling
or installation.
We are not liable for any problems caused by unauthorized modification or attempted repair.

2．Installation

Do not apply power to the IP camera before completing installation.
Do not put object on the IP camera.

3．Environment

This series IP camera should be installed in a cool, dry place away from direct sunlight, inflammable,
explosive substances and etc.
The working temperature ranges from -10℃ to +60℃. Please keep it away from the electromagnetic
radiation object and environment.
Please keep the sound ventilation.
Do not allow the water and other liquid falling into the IPC.
Thunder-proof device is recommended to be adopted to better prevent thunder.
The grounding studs of the product are recommended to be grounded to further enhance the reliability
of the camera.

4. Daily Maintenance

Current series IPC has no power button. Please unplug all corresponding power cables before your
installation.
Do not touch the CCD or CMOS part; you can use the blower to clean the dust on the surface of the
lens. You can use the dry cloth with some alcohol to clear if necessary.
Please keep the dustproof cap back to protect the CCD or CMOS part if the IP camera does not work
for a long time.

If there is too much dust on the housing, please use the water to dilute the mild detergent first and then
use it to clean the device with the clear dry cloth. Finally use the dry cloth to clean the device.

5. Accessories

Please open the accessory bag to check the items one by one in accordance with the list below.
Contact your local retailer ASAP if something is missing or damaged in the bag.

Accessory Name Amount
IPC Unit
C/CS adapter

■ 1

■ 1

ii

Quick Start

eLineTechnology.com

Guide

■ 1

CD

■ 1

iii

Table of Contents

eLineTechnology.com

1 General Introduction ..................................................................................................................1

1.1 Overview........................................................................................................................1

1.2 Feature...........................................................................................................................1

1.3 Specifications................................................................................................................2

1.3.1 Performance...........................................................................................................2

1.3.2 Factory Default Setup...........................................................................................4

2 Framework.................................................................................................................................13

2.1 Rear Panel...................................................................................................................13

2.2 Side Panel ...................................................................................................................17

2.3 Front Panel..................................................................................................................17

2.4 Bidirectional talk .........................................................................................................18

2.4.1 Device-end to PC-end........................................................................................18

2.4.2 PC-end to the Device-end..................................................................................18

2.5 Alarm Setup.................................................................................................................19

2.5.1 Alarm Input and Output Connection.................................................................19

2.5.2 IR Light Connection ............................................................................................20

3 Installation .................................................................................................................................21

3.1 Lens Installation..........................................................................................................21

3.1.1 Auto Aperture Lens.............................................................................................21

3.1.2 Manual Lens.........................................................................................................21

3.1.3 Remove Lens.......................................................................................................22

3.2 SD Card .......................................................................................................................22

3.2.1 Installation ............................................................................................................22

3.2.2 Remove.................................................................................................................23

3.3 3G Card .......................................................................................................................23

3.4 3G/WIFI Antenna........................................................................................................25

3.3.1 Installation ............................................................................................................23

3.3.2 Remove.................................................................................................................24

iv

3.4.1 Installation ............................................................................................................25

eLineTechnology.com

3.4.2 Remove.................................................................................................................25

3.5 I/O Port.........................................................................................................................26

4 Quick Configuration Tool.........................................................................................................28

4.1 Overview......................................................................................................................28

4.2 Operation .....................................................................................................................28

5 Web Operation..........................................................................................................................31

5.1 Network Connection...................................................................................................31

5.2 Login and Logout........................................................................................................31

6 FAQ ............................................................................................................................................34

Appendix Toxic or Hazardous Materials or Elements ...............................................................35

v

eLineTechnology.com

1 General Introduction

1.1 Overview

This series IP camera integrates the traditional camera and network video technology. It adopts
audio video data collection, transmission, storage together. It can connect to the network directly
without any auxiliary device.

This series IPC uses standard H.264 video compression technology and PCM, G.711a/u audio
compression technology, which maximally guarantees the audio and video quality.

This series IPC has mega pixel resolution and supports 12V DC/24V AC power. It supports the
wireless network application, bidirectional talk, digital water mark and etc.

It can be used alone or used in a network area. When it is used lonely, you can connect it to the
network and then use a network client-end. Due to its high definition, multiple functions and
various applications, this series IPC is widely used in many indoor environments and other
important area surveillance.

1.2 Feature

User

Management

Data

Transmission

Storage

Function

Alarm

Function

Network

Monitor

Network

Management

Peripheral

Equipment

Power

z Different user rights for each group, one user belongs to one group.
z The user right can not exceed the group right.

z Support cable network data transmission via Ethernet
z Wireless device supports WIFI/3G wireless data transmission.

z Support central server backup function in accordance with your configuration and

setup in alarm or schedule setting

z Support record via Web and the recorded file are storage in the client-end PC.
z Support local SD card hot swap. Support short-time storage when encounter

disconnection.

z Support network storage such as FTP.
z Real-time respond to external on-off alarm input, and video detect as user pre-

defined activation setup and generate corresponding message in screen and audio
prompt(allow user to pre-record audio file)

z Real-time video detect: motion detect, camera masking.
z IPC supports one-channel audio/video data transmit to network terminal and then

decode. Delay is within 270ms (network bandwidth support needed)

z Max supports 20 connections.
z Adopt the following audio and video transmission protocol: HTTP, TCP, UDP,

MULTICAST, RTP/RTCP, RTSP and etc.

z Support web access.
z Realize IPC configuration and management via Ethernet.
z Support device management via web.
z Support various network protocols.
z Support peripheral equipment connection via the RS232 port, each peripheral

equipment control protocol and interface can be set freely.

z Support serial port (RS232/RS485) transparent data transmission.
z Support the on-off alarm device to alarm via the sound or the light.
z External power adapter. Support DC 12V/AC 24V power supply.

PoE

z Support Power over Ethernet (PoE). Conform to the IEEE802.3af standard.
z Connect the device to the switcher or the router that supports the PoE function to

1

eLineTechnology.com

realize the network power supply.

z To guarantee proper performance, please make sure the power sourcing device

can supply at least 10W power.

z Usually, do not use the PoE for the WIFI/3G device.
z Day/Night mode auto switch (ICR switch.)
z Backlight compensation: screen auto split to realize backlight compensation to

adjust the bright.

Assistant

Function

z Support system resource information and running status real-time display. Support

log function.

z Support video watermark function to avoid vicious video modification.
z Support auto aperture.
z Support picture parameter setup such as electronic shutter and gain setup.
z Support dual-stream, ACF(Active frame control )

1.3 Specifications

1.3.1 Performance

Please refer to the following sheet for IPC performance specification.

Model
Parameter

System

Main
Processor
OS Embedded LINUX

System
Resources

User Interface Remote operation interface such as WEB, DSS, PSS
System Status SD card status, bit stream statistics, log, and software version.

Video Parameter

Image Sensor

Pixel
Day/Night

Mode
Auto Aperture Optional

Gain Control Fixed/Auto

IPC-HF3500
Series

TI Davinci high performance DSP

Support real-time network, local record, and remote operation at the same
time.

1/2.5-inch
CMOS

2560(H)*192
0(V)

Support day/night mode switch and IR-CUT at the same time.

IPC-HF3300
Series

1/2.8-inch
CMOS

2080(H)*155
3(V)

IPC-HF3200
Series

1/2.9-inch
CMOS

1920(H)*120
0(V)

IPC-HF3100
Series

1/3-inch
CMOS

1280(H)*960(
V)

IPC-HF3110
Series

1/3-inch CCD
1280(H)*960(

V)

White Balance On/off
BLC On/off

Electronic
Shutter

Video
Compression
Standard

Manual/Auto
PAL: It ranges from 1/3 to 1/10000.
NTSC: It ranges from 1/4 to 1/10000.

H.264/H.264B/MJPEG

Manual/Auto
PAL: It
ranges from
1/3 to
1/100000.
NTSC: It
ranges from
1/3 to
1/100000.

2

eLineTechnology.com

Video Frame
Rate

Video Bit Rate

PAL: Main
stream
(2560*1920
@8fps)
Extra
stream(704*5
76@8fps)
Main stream

(1920*1080
@25fps)

Extra stream

(704*576@2
5fps)

NTSC：Main
stream
(2560*1920
@8fps)
Extra stream
(704*480@8f
ps)
Main stream
(1920*1080
@30fps)
Extra stream
(704*480@3
0fps)

H.264: 56Kbps-8192Kbps.
ＭJPEG is adjustable and bit rate is adjustable.
Support customized setup.

PAL: Main
stream
(2048*1536
@15fps)
Extra
stream(704*5
76@15fps)
Main stream

(1920*1080
@25fps)

Extra stream

(704*576@2
5fps)

NTSC：Main
stream
(2048*1536
@15fps)
Extra stream
(704*480@1
5fps)
Main stream
(1920*1080
@30fps)Extra
stream
(704*480@3
0fps)

PAL: Main
stream
（ 1920*1080

@25fps）
extra stream

（ 704*576
@25fps）

NTSC： Main
stream
(1920*1080
@30fps)
Extra stream
(704*480@3
0fps)

PAL: Main
stream
（ 1280*960

@25fps），
extra stream,
（ 704*576@
25fps）

NTSC： Main
stream
(1280*960@
30fps)
Extra stream
(704*480@3
0fps)

PAL: Main
stream
（ 1280*960

@12.5fps ）
，
extra stream,
（ 704*576@

12.5fps）
Main stream

（ 1280*720
@25fps），
extra stream

(704*576@2
5fps）

NTSC：Main
stream
(1280*960@

12.5fps)Extra
stream
(704*480@1

2.5fps)
Main stream
(1280*720@
30fps)
Extra stream
(704*480@3
0fps)

Flip Support
Mirror Support

Snapshot Max 1f/s snapshot. File extension name is JPEG
Privacy Mask Each channel supports max 4 privacy mask zones
Video Setup Support parameter setup such as bright, contrast.

Video
Information

Lens Optional
Lens Interface C/CS optional
Audio Input

Audio

Audio Output
Bidirectional

Talk Input
Audio Bit Rate 16kbps 16bit
Audio

Compression
Standard

Video

Motion Detect

Camera
Masking

Channel title, time title, motion detect, privacy mask.

1-channel， 3.5mm JACK LINE IN
1-channel， 3.5mm JACK SPEAK OUT

Reuse the first audio input channel

G.711A/G.711Mu/PCM

396 (18*22) detection zones；sensitivity level ranges from 1 to 6 (The 6th
level has the highest sensitivity)
Activation event, alarm device, audio/video storage, image snapshot, log,
email function and etc.
Sensitivity level ranges from 1 to 6. Each sensitivity level is the percentage of
the privacy mask zone.

3

eLineTechnology.com

Activation event, alarm device, audio/video storage, image snapshot, log,
email SMTP function and etc.

Alarm Input

Record and

Backup

Record
Priority

Local Storage Support local SD card hot swap

1-channel input，1-channel output
Manual>External alarm >Video detect>Schedule

Storage
Management

Network

Wire Network 1-channel wire Ethernet port, 10/100 Base-T Ethernet
Network

Protocol
Remote

Operation

AUX Interface

Video Output
Network

Interface
3G Port

Antenna Port
RS485 port PTZ control interface. Support various protocols.

General Parameter

Power
Power

Consumption
Working

Temperature

Working
Humidify

Dimensions 70*63.2*149.5
Weight 650g
Installation

Support display local storage status

Standard HTTP, TCP/IP, ARP, IGMP, ICMP, RTSP, RTP, UDP, RTCP, SMTP,
FTP, DHCP, DNS, DDNS, PPPOE, UPNP, NTP, Bonjour, SNMP.

Monitor, PTZ control, system setup, file download, log information,
maintenance , upgrade and etc

1-channel analog video output，BNC port
1-channel Ethernet, 10/100 Base-T Ethernet (The IPC-HF3110-F series

product has the optical port.)
Support 3G SIM card, TD/EVDO/WCDMA function. (For 3G series product

only.)
Support to receive the wireless signal (This function is for 3G and WIFI series
product only.)

Support AC24V/DC12V power and PoE. (The IPC-HF3110-F/W/E/T/C series
product does not support the PoE function.)

<10W (For WIFI and 3G device, it is below 12W.)

-10 ~+60℃℃ (For –W device, it is from -10 ~+℃ 55℃. For 3G device, it is from -
10 ~+℃ 50℃ )

10%~90%

Support various installation modes（Enclosure and bracket is optional）

1.3.2 Factory Default Setup

Please refer to the following sheet for factory default setup information.

Default Setup

Setup Item

Camera

Conditions

Brightness 50
Contrast 50
Hue 50
Saturation 50

Exposure Mode Auto
Gain Scope 0~80

IPC­HF3500

Series

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

4

eLineTechnology.com

Default Setup

Setup Item

Auto Iris On
Profile Auto
Day&Night Auto
Backlight Off

Mirror Off
Flip Off

Video bit stream

Video

Main
Stream

Sub
Stream

IPC­HF3500

Series

Bit stream
type

Encode
mode

Resolution 1080P（1920*1080） 720P（1280*720）
Frame

Rate
（FPS）

Bit Rate
Type

Recommen
ded Bit

Bit Rate 8192
I Frame 50
Watermark Enable
Watermark

character

Enable Enable
Bit stream

type
Encode

mode
Resolution CIF(352*288/352*240)
Frame

Rate
（FPS）

General

H.264

PAL: 25
NTSC:30

CBR

3584-8192 Kb/S

DigitalCCTV

General

H.264B

PAL: 25
NTSC:30

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

Snapshot

Bit Rate
Type

Recommen
ded Bit

Bit Rate 1024
I Frame 50

Snapshot
Type

Image
Size

Quality 5

CBR

192-1024Kb/S

General

1080P（1920*1080） 720P（1280*720）

5

eLineTechnology.com

Default Setup

Setup Item

Video Overlay

Path

Audio

Main Stream

Sub Stream

Network

TCP/IP

IPC­HF3500

Series

Interval 1s
Privacy

Mask
Channel

Title
Time Title Enable

Snapshot
Path

Record
Path

Enable Enable
Encode

Mode
Enable Disable
Encode

Mode
Host Name IPC
Ethernet

Card
Mode Static
Mac

Address
IP Version IPV4
IP Address 192.168.1.108
Subnet

Mask
Default

Gateway

Disable

Enable

C:\PictureDownload

C:\RecordDownload

G.711A

G.711A

Wire(Default)

Device MAC address when it is shipped out of the factory

255.255.255.0

192.168.1.1

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

Connection

Preferred
DNS

Alternate
DNS

Enable
ARP/Ping
set device
IP address
service

Max
Connection

TCP Port 37777
UDP Port 37778
HTTP Port 80

8.8.8.8

8.8.8.8

Enable

10

6

eLineTechnology.com

Default Setup

Setup Item

PPPoE

DDNS

IPC­HF3500

Series

RTSP Port 554

HTTPs
Port

Enable Disable
Username N/A
Password N/A
Server

Type
Server IP none

Server Port 80
Domain

Name
User none

443

Disable，CN99 DDNS

none

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

IP Filter

SMTP(Email)

Password N/A
Update

Period
Trusted

sites
SMTP

Server
Port 25

Anonymity Disable
User Name anonymity
Password N/A
Sender none
Authenticat

ion
(Encryption
mode)

Title
(Subject)

10 minutes

Disable

none

N/A

IPC Message

Attachment Enable
Mail

Receiver
Send

Interval
Email Test Disable，interval=60 minutes

N/A

0 second

7

eLineTechnology.com

Default Setup

Setup Item

UPnP

SNMP

Bonjour

Multicast

QoS

Event

Video detect

Motion Detect

IPC­HF3500

Series

Enable
UPnP

SNMP v1 Disable
SNMP v2 Disable

SNMP Port 161
Read

Community
Write

Community
Trap

Address
Trap Port 162
SNMP

Enable Enable
Server

Name
Multicast

Address
Port 36666
Real-time

Monitor
Command 0

Wireless
Qos

Enable Disable
Anti-dither 5 seconds
Sensitivity 3
Record

Channel
Record

Delay
Relay out Enable
Alarm

Delay
Send Email Disable
PTZ Disable
Activation

Operation
Address 0
Snapshot Disable

Disable

public

private

N/A

v3 disable

“SN”. It depends on the device.

239.255.42.42

0

Disable

Enable

10 seconds

10 seconds

N/A

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

8

eLineTechnology.com

Default Setup

Setup Item

Alarm

Abnormity

IPC­HF3500

Series

Enable Disable
Record

Channel

Record
Delay

Relay out Enable
Video
Masking

Alarm
Activation

Relay output 1

No SD Card

Capacity
Warning

Record

Delay

Send Email Disable

PTZ Disable

Activation

Operation

Address 0

Snapshot Disable

Enable Disable

Relay in Alarm 1

Anti-dither 0 seconds

Sensor

Type

Record

Channel

Record

Delay

Relay out Enable

Alarm

Delay

Send Email Disable

PTZ Disable

Activation

Operation

Address 0

Snapshot Disable

Enable Disable

Relay out Enable

Relay out

Delay

Send email Disable

Enable Disable

Capacity

Limit

Enable

10 seconds

10 seconds

N/A

NO

Enable

10 seconds

10 seconds

N/A

10 seconds

10%

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

9

eLineTechnology.com

Default Setup

Setup Item

Relay out Enable

Relay out

Delay

Send Email Disable

Enable Disable
SD Card

Error

Disconnectio
n

IP Conflict

Relay out Enable

Relay out

Delay

Send email Disable

Enable Disable

Record Enable

Record

Delay

Relay out Enable

Relay out

Delay

Enable Disable

Record Enable

Record

Delay

Relay out Enable

IPC­HF3500

Series

10 seconds

10 seconds

10 seconds

10 seconds

10 seconds

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

Storage

Period

Setup

Storage

FTP

Record Control

Relay out

Delay

Week Enable

Time 00:00:00 to 24:00:00

Schedule Disable

Motion

Detect

Alarm Enable

Enable

FTP

Server IP N/A

Port 21

Username anonymous

Password N/A

Remote

path

Emergency

(Local)

Pack

Duration

10 seconds

Enable

Disable

share

Disable

8 minutes

10

eLineTechnology.com

Default Setup

Setup Item

System

General

Local Host

IPC­HF3500

Series

Pre-record 5 seconds

Disk Full Overwrite

Record

Mode

Record

Stream

Device No Device factory SN

Language English

Video

Standard

Date

Format

Time

Format

Auto

Main Stream

PAL

Y-M-D

24H

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

Date and
time

PTZ

Time Zone GMT+08:00

System

Time

DST Disable

DST Type Week

Start Time 00:00:00 of the first Sunday of the month

End Time 00:00:00 of the second Monday of the month

NTP Disable

NTP

Server

Port 37

Update

Period

Protocol PELCOD

Address 1

Baud Rate 9600

Data Bit 8

Sync PC

clock.isc.org

10 minutes

Auto Maintenance

Stop bit 1

Parity N/A

Auto

Reboot

Auto

Delete Old

Files

Enable 02:00 each day.

Disable

11

eLineTechnology.com

Default Setup

Setup Item

System Log

IPC­HF3500

Series

End Time Current time

Start Time The previous day

All Types Select all

IPC­HF3300

Series

IPC­HF3200

Series

IPC­HF3100

Series

IPC­HF3110
Series

12

eLineTechnology.com

2 Framework

2.1 Rear Panel

This series IP camera real panel is shown as below. See Figure 2-1.

The rear panel with the network port

Please refer to the following sheet for detail information.

Interface Name Connector Function
VIDEO OUT Video output port BNC Output analog video

The rear panel with the 100M fiber port

Figure 2-1

signal. Can connect to

13

eLineTechnology.com

TV monitor to view
video.

AC 24V/ DC 12V Power port z Power port.

z Input 12V DC or

AC 24V
STATUS
Indication Light

Red light z System boot up-

Green light z Normal working

red light is on

z System

upgrades-red light

flashes

z System resets-

red light flashes.

status-green light

is on.

z Display record

status: Record-

green light

flashes.

Yellow light

3G

WIFI Antenna port Connect to 3G/WIFI

IN Alarm input port I/O port Alarm input port 1. To

z Detect the

wireless device-

yellow light is on.

Connect to 3G card.
Please note it is for
3G series product
only.

antenna to receive the
wireless signal.
Please note this
function is for some
series products only.

receive the signal from

14

eLineTechnology.com

the external alarm

device.
NO
C

G GND Alarm input ground

A RS485_A port, control

B

RX RS232_RX，RS232

Alarm output port Alarm output port. To

output alarm signal to

the alarm device.

z NO: Normal open

alarm output end.

z C: Alarm output

public end.

end.

RS485 port

external PTZ

RS485_B port, control

external PTZ

RS232 port

receive end.
TX

G GND RS232 ground end

NA IR light port External IR light signal

RESET RESET button Restore factory default

RS232_TX，RS232

COM send out end.

control port.

setup.

When system is

running normally,

press the RESET

button for at least 5

seconds, system can

restore factory default

setup.
AUDIO OUT Audio output port Audio output 3.5mm

AUDIO IN Audio input port Audio input 3.5mm Input audio signal

JACK port.

Output audio signal to

the passive device

such as earphone.

15

eLineTechnology.com

JACK port. from devices such as

pick-up.
LAN Network port Ethernet port z Connect to

standard Ethernet
cable.

z Support PoE

function.

OPT 100M fiber port 155M single fiber

dual-direction SFP
fiber module

SD SD card port Connect to SD card.

Transmit 100M

Ethernet data.

Note

z When you install

the SD card,
please make sure
current card is not
in write mode and
then you can
install it to the
camera.

z When you

remove the SD
card, please
make sure current
card is not in write
mode. Otherwise
it may result in
data loss or card
damage.

z Before hot swap,

please stop
record operation.

16

eLineTechnology.com

GND Please make sure the

device is securely

earthed to prevent the

thunderstorm strike.

2.2 Side Panel

Please refer to the following interface for side panel dimension information. The unit is mm. See
Figure 2-2.

Figure 2-2

2.3 Front Panel

Please refer to the following interface for the front panel information. The unit is mm. See Figure
2-3.

17

eLineTechnology.com

Figure 2-3

2.4 Bidirectional talk

2.4.1 Device-end to PC-end
Device Connection

Please connect the speaker or the MIC to the audio input port in the device rear panel. Then
connect the earphone to the audio output port in the PC.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.

Listening Operation

At the device end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the pc-end.

2.4.2 PC-end to the Device-end
Device Connection

Connect the speaker or the MIC to the audio input port in the PC and then connect the earphone
to the audio output port in the device rear panel.
Login the Web and then click the Audio button to enable the bidirectional talk function.
You can see the button becomes orange after you enabled the audio talk function.
Click Audio button again to stop the bidirectional talk function.

Please note the listening operation is null during the bidirectional talk process.

Listening Operation

At the PC-end, speak via the speaker or the pickup, and then you can get the audio from the
earphone or sound box at the device-end.

18

eLineTechnology.com

2.5 Alarm Setup

The alarm setup interface is shown as below. See Figure 2-4.

z Connect the alarm input device to the alarm input port.
z Connect the alarm output device to the alarm output port and alarm output public port. The

alarm output port supports NO (normal open) alarm device only.

z Open the Web, go to the Figure 2-4. Here you can set the alarm input setup and alarm

output setup. Please set the alarm in for the alarm input in the rear panel. Then you can
select the corresponding type (NO/NC) according to the high/low level type when an alarm
occurs.

z Set the WEB alarm output. The alarm output 01 is the alarm output port of the device rear

panel.

Figure 2-4

2.5.1 Alarm Input and Output Connection

Please refer to the following figure for alarm input information. See Figure 2-5.
Alarm input: When the input signal is idle or grounded, the device can collect the different
statuses of the alarm input port. When the input signal is connected to the 5V or is idle, the
device collects the logic “1”. When the input signal is grounded, the device collects the logic “0”.

Figure 2-5

Please refer to the following figure for alarm output information. See Figure 2-6.
Port NO and Port C composes an on-off button to provide the alarm output.
If the type is NO, this button is normal open. The button becomes on when there is an alarm
output.

19

eLineTechnology.com

If the type is NC, this button is normal off. The button becomes off when there is an alarm output.

Figure 2-6

2.5.2 IR Light Connection

Please refer to the following figure for external IR light information. See Figure 2-7.
IR synchronization input signal. When the external IR light is on, the signal cable from the board
outputs the 3.3V/1mA. It outputs the 0V when the IR light is off.

Figure 2-7

20

eLineTechnology.com

3 Installation

3.1 Lens Installation

3.1.1 Auto Aperture Lens

Please follow the steps listed below for auto aperture lens installation. The interface is shown as
in Figure 3-1 and Figure 3-2.
z Remove the CCD protection cap of the device, and then line up the lens to the proper

installation position. Turn clockwise until the lens is fixed firmly.

z Insert the lens cable socket to the auto lens connector in the side panel.

Figure 3-1

3.1.2 Manual Lens

Install C type lens

z Remove the CCD protection cap from the device.
z Install the C/CS adapter to the camera. Turn clockwise to secure against the focusing ring

firmly.

z Line up the C lens to the installation position of the C/CS adapter. Turn clockwise to fix the

lens.

z Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter

clockwise to move the focusing ring out for several millimeters. Now you can focus manually
and check the video is clear or not. If you can not see the clear video, you can adjust via the
flange-back.

z After you completed the focus setup, use the slotted screwdriver to fix the screw firmly.

Fasten the focusing ring. Now the installation completed.

Install CS type lens

z Remove the CCD protection cap from the device.
z Line up the CS lens to the lens installation position of camera focusing ring. Turn clockwise

to fix the lens.

z Use slotted screwdriver to fasten the screw near the focusing ring and then turn counter

clockwise to move the focusing ring out for several millimeters. Now you can focus manually
and check the video is clear or not. If you can not see the clear video, you can adjust via the
flange-back.

z After you completed the focus setup, use the slotted screwdriver to fix the screw firmly.

Fasten the focusing ring. Now the installation completed.

21

eLineTechnology.com

Figure 3-2

3.1.3 Remove Lens

Please follow the steps listed below to remove lens. The interface is shown as in Figure 3-3.

z Turn the lens counter clockwise and then remove it from the camera.
z Unplug the auto lens cable socket from the auto lens connector. If you are using the manual

aperture lens, please skip to the following step.

z If there is no lens, please put the CCD protection cap back to protect the CCD.

Figure 3-3

3.2 SD Card

3.2.1 Installation

Please follow the steps listed below to install SD card. The interface is shown as in Figure 3-4
and Figure 3-5.
z Use the screwdriver to loosen the SD card protection screw in the rear panel, and then

remove the SD card protection cap from the camera.

z Install the SD card to the camera according to the proper installation position.
z Put the SD card protection cap back.
z Use the screwdriver to fix the SD card protection cap screw firmly to secure the SD card

protection cap in the camera.

22

eLineTechnology.com

Figure 3-4

Figure 3-5

3.2.2 Remove

Please follow the steps listed below to remove SD card. The interface is shown as Figure 3-6.
z Use the screwdriver to loosen the screw of SD card protection cap in the rear panel.

Remove the cap from the camera.

z Follow the SD card direction to remove the SD card.
z Insert the SD card protection cap.
z Use the screwdriver to fix the screw to secure the protection cap.

3.3 3G Card

3.3.1 Installation

The 3G card installation is the same with the SD card.
Please follow the steps listed below to install 3G card. The interfaces are shown as Figure 3-7
and Figure 3-8.

Figure 3-6

23

eLineTechnology.com

z Use the screwdriver to loosen the 3G card protection cap screw in the side panel, and then

remove the 3G card protection cap from the camera.

z Install the 3G card to the camera according to the proper installation position.
z Put the 3G card protection cap back.
z Use the screwdriver to fix the 3G card protection cap screw firmly to secure the 3G card

protection cap.

Figure 3-7

Figure 3-8

3.3.2 Remove

Please follow the steps listed below to remove 3G card. The interface is shown as Figure 3-9.
z Use the screwdriver to loosen the screw of 3G card protection cap in the rear panel.

Remove the cap from the camera.

z Follow the 3G card direction to remove the 3G card.
z Insert the 3G card protection cap.
z Use the screwdriver to fix the screw to secure the protection cap.

Figure 3-9

24

eLineTechnology.com

3.4 3G/WIFI Antenna

3.4.1 Installation

Line up the thread of the screw of the 3G/WIFI antenna to the thread of the rear panel. See
Figure 3-10.
Please turn according to the direction in the following figure until antenna is secure firmly. See
Figure 3-11.

Figure 3-10

Figure 3-11

After you fix the 3G/WIFI antenna to the WIFI port of the rear panel, you can adjust the antenna
direction. See Figure 3-12.

Figure 3-12

3.4.2 Remove

25

eLineTechnology.com

Use your hands to hold the 3G/WIFI thread end and then turn according to the following figure.
See Figure 3-13.
Now you can see the antenna is away from the thread. See Figure 3-14.

Figure 3-13

Figure 3-14

Remove the 3G/WIFI antenna from the port of the rear panel. See Figure 3-15.

Figure 3-15

3.5 I/O Port

Install Cable

Please follow the steps listed below to install the cable. See Figure 3-16.

26

eLineTechnology.com

Use the small slotted screwdriver to press the corresponding button of cable groove. Insert the
cable into the groove and then release the screwdriver.

Remove Cable

Please follow the steps listed below to remove the cable.
Use the small slotted screwdriver to press the corresponding button of cable groove. Remove the
cable out of the groove and then release the screwdriver.

Figure 3-16

27

eLineTechnology.com

4 Quick Configuration Tool

4.1 Overview

Quick configuration tool can search current IP address, modify IP address. At the same time, you
can use it to upgrade the device.
Please note the tool only applies to the IP addresses in the same segment.

4.2 Operation

Double click the “ConfigTools.exe”icon, you can see an interface is shown as in Figure 4-1.
In the device list interface, you can view device IP address, port number, subnet mask, default
gateway, MAC address and etc.

Figure 4-1

Select one IP address and then right click mouse, you can see an interface is shown as in Figure
4-2.

Figure 4-2

28

eLineTechnology.com

Select the “Open Device Web” item; you can go to the corresponding web login interface. See
Figure 4-3.

Figure 4-3

If you want to modify the device IP address without logging in the device web interface, you can
go to the configuration tool main interface to set.
In the configuration tool search interface (Figure 4-1), please select a device IP address and then
double click it to open the login interface. Or you can select an IP address and then click the
Login button to go to the login interface. See Figure 4-4.
In Figure 4-4, you can view device IP address, user name, password and port. Please modify the
corresponding information to login.
Please note the port information here shall be identical with the port value you set in TCP port in
Web Network interface. Otherwise, you can not login the device.
If you are use device background upgrade port 3800 to login, other setups are all invalid.

After you logged in, the configuration tool main interface is shown as below. See Figure 4-5.

Figure 4-4

29

eLineTechnology.com

Figure 4-5

For detailed information and operation instruction of the quick configuration tool, please
refer to the Quick Configuration Tool User’s Manual included in the resources CD.

30

eLineTechnology.com

5 Web Operation

This series IPC product support the Web access and management via PC.
Web includes several modules: monitor channel preview, PTZ control, system configuration,
alarm and etc.

5.1 Network Connection

Please follow the steps listed below for network connection.

z Make sure the IPC has connected to the network properly.
z Please set the IP address, subnet mask and gateway of the PC and the IPC respectively.

IPC default IP address is 192.168.1.108. Subnet mask is 255.255.255.0. Gateway is

192.168.1.1.

z Use order ping ***.***.***.***(* IP camera address) to check connection is OK or not.

5.2 Login and Logout

Open IE and input IP camera address in the address bar.
For example, if your camera IP is 192.168.1.108, then please input http:// 192.168.1.108 in IE
address bar. See Figure 5-1.

Figure 5-1

The login interface is shown as below. See Figure 5-2.
Please input your user name and password.
Default factory name is admin and password is admin.

Note: For security reasons, please modify your password after you first login.

Input your IP
address here

31

eLineTechnology.com

Figure 5-2

If it is your first time to login in, system pops up warning information to ask you whether install
control webrec.cab or not after you logged in for one minute. Please click OK button, system can
automatically install the control. When system is upgrading, it can overwrite the previous Web too.
If you can’t download the ActiveX file, please check whether you have installed the plug-in to
disable the control download. Or you can lower the IE security level. See Figure 5-3.

After you logged in, you can see the main window. See Figure 5-4.

Figure 5-3

32

eLineTechnology.com

Figure 5-4

Please refer to the Web Operation Manual included in the resource CD for detailed operation
instruction.

33

eLineTechnology.com

6 FAQ

Bug
I can not boot up

the device or can
not control the
device.

SD card hot swap Before draw out SD card, please stop record or snapshot first and

SD card write
times

I can not use the
disk as the storage
media.

I can not upgrade
the device via
network.

Recommended SD
card brand

Please click RESET button for at least five seconds to restore
factory default setup.

then wait for at least 15 seconds to remove the SD card. All the
operations before is to maintain data integrity. Otherwise you can
lose all the data in the SD card!

Do not set the SD card as the storage media to storage the
schedule record file. It may damage the SD card duration.

When disk information is shown as hibernation or capacity is 0,
please format it first (Via Web).

The status indication light is shown as red when network upgrade
operation failed. You can use port 3800 to continue upgrade.

Kingston 4GB, Kingston 16GB, Kingston32GB, Transcend 16GB,
SanDisk 4GB, SanDisk 32GB.

Usually we recommend the 4GB (or higher) high speed card in case
the slow speed results in data loss.

Audio function Please use active device for the audio monitor input, otherwise there

is no audio in the client-end.

34

eLineTechnology.com

Appendix Toxic or Hazardous Materials or Elements

Toxic or Hazardous Materials or Elements Component Name

Pb Hg Cd Cr VI PBB PBDE

Circuit Board Component ○ ○ ○ ○ ○ ○

Device Construction Material ○ ○ ○ ○ ○ ○

Wire and Cable ○ ○ ○ ○ ○ ○

Power Adapter ○ ○ ○ ○ ○ ○

Packing Components ○ ○ ○ ○ ○ ○

Accessories ○ ○ ○ ○ ○ ○

O: Indicates that the concentration of the hazardous substance in all homogeneous materials in
the parts is below the relevant threshold of the SJ/T11363-2006 standard.

X: Indicates that the concentration of the hazardous substance of at least one of all
homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006
standard. During the environmental-friendly use period (EFUP) period, the toxic or hazardous
substance or elements contained in products will not leak or mutate so that the use of these
(substances or elements) will not result in any severe environmental pollution, any bodily injury or
damage to any assets. The consumer is not authorized to process such kind of substances or
elements, please return to the corresponding local authorities to process according to your local
government statutes.

Note

z This user’s manual is for reference only.
z Slight difference may be found in user interface.
z All the designs and software here are subject to change without prior written notice.
z If there is any uncertainty or controversy, please refer to the final explanation of us.
z Please visit our website for more information.

35