eLine Technology ANPTZ-Controller User Manual
IR Remote Controller
1
Installation
485 B/-
485 A/+
Connect485porttoPTZdome485cable,
Connect DC12V to power port.
After power on, controller will display
P001
or
A
means address of command, 001 is
address number.
means preset point, 001 is preset number.
P
Protocol :Pelco-D
Protocol :Pelco-D
Bitrate:2400bps
Bitrate:2400bps
A001
ESC
PATTERN
DISP
PRSET
A
RUN
HOME
-/--
C
SHOT
SPEED
FOCUS+
FOCUS+
OPEN
ZOOM+
IRIS
FOCUS-
ZOOM-
CLOSE
S3S2
S1
F1
F3F2
P3
P1
P2
P7P6
P5
2
Set target camera addressSet target camera address
Press button go to address command mode.
CAM
It is a command of selecting your target camera,
3
Preset PointPreset Point
Press button go to preset selecting mode.
SHOT
It is a command of selecting preset of your
target camera,
Atthismode,youcaninputanumberbypress
Atthismode,youcaninputanumberbypress
keyboard numeric key, this is preset number
keyboard numeric key,
Ifyouwantinputanumbermorethan10,
-/--
ENTER
C
Ifyouwantinputanumbermorethan10,
You need press button change to plus 10
-/--
mode.Youcaninput3numberatthismode.
After enter you need input button
confirm it.Press button do backspace.
C
ENTER
You need press button change to plus 10
mode.Youcaninput3numberatthismode.
After enter you need input button
confirm it. Press button do backspace.
Ifyouwantsetapresetnumber,youneed
SETUP
DELETE
B
At any mode, if you press button, system will
ESC
go to address input mode.
will display , at this time you can input a
number, if you need input a number more
than 10, you need press button at first.
After input number, need press key
press button 3 seconds, and controller
PRSET
SET-
-/-ENTER
confirm it.
CAM
Ifyouonlywantchangeaaddressnumberbelow
10, you only need press one time.numeric key
AUTO
Ifyouwantclearapresetnumber,youneed
S4
F4
P4
P8
press button 3 seconds, and controller
will display , You can input number same
as set preset.
DELETE
CLR-
Youcanusesamewayset/clear/goto
and (left limited point) (right limited point)
AB
HOME
IR REMOTE CONTROLLER GUIDE
IR Remote Controller
4
Function ListFunction List
C
-/--
Protocol:Pelco-D
Bitrate:2400bps
UP DOWN LEFT RIGHT
button is controls the
movement of pan
and tilt cameras
ENTER
button is a stop
key at movement,
Anditalsoisaconfirm
key when input a number
Numerickey0-9
is
number input button
button is a backspace
C
for number input
is a button for change
-/--
plus10 mode and normal
mode, in normal mode only
caninputnumber0-9,
in plus10 mode can input
number0-255
5
ESC
CAM
SHOT
HOME
A
B
P1
P5
PRSET
DELETE
AUTO
SPEED
At any mode, if you press button,
ESC
system will go to address input mode.
Press button go to address
CAM
input mode
Press button go to preset
SHOT
selecting mode.
It is a command of selecting preset
of your target camera,
HOMEAB P1-P8
and isshortcutkey
forpresetpoint
P3
P2
PRESET
DELECT
P4
P7P6
P8
issetpresetpoint
is clear preset point
Thistwokeyneedpressmorethan3
seconds to active it.
AUTO
is go to auto cruise mode,
Another auto mode is go to
preset point 99
SPEED
S1 -S4
is set speed of movement
is shortcut key for speed
S1=8,S2=40,S3=51,S4=63
FOCUS+
FOCUS+
FOCUS-
OPEN
IRIS
CLOSE
ZOOM+
ZOOM-
PATTERN
RUN
DISP
F1
SETUP
FOCUS +
FOCUS -
OPEN
CLOSE
ZOOM +
ZOOM -
PATTERN
RUN
a pattern
DISP
F1-F4
display software version
user define shortcut key
F4F3F2
focus far
focus near
Iris open
Iris close
zoom wide
zoom tele
start / stop learn pattern
S1
S3S2
S4
IR REMOTE CONTROLLER GUIDE
Loading...