AN2 Series
CMOS Technology High Resolution Sensor
900tvl
P/N 01.BSM.16.2000030 V1.0
Product Made in China under ISO9001 & ISO1400 standards
Manual Printed in China v1.0
eLineTechnology.com
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK)
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The lightning with an arrowhead symbol, within an equilateral triangle
is intended to alert the users to the presence of un-insulated
“dangerous voltage” within the product’s enclosure that may be
sufcient magnitude to constitute a risk of electric shock to persons.
The exclamation point with an equilateral triangle is intended to alert
the user to the presence of important operating and maintenance
(servicing) instructions in the literature accompanying the appliance.
This equipment has been tested and found to comply with limits for a Class
A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy, if not
installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the
interference at his own expense.
Changes or modications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
To prevent electric shock and risk of re hazards:
• Do NOT use power sources other than that specied.
• Do NOT expose this appliance to rain or moisture.
This installation should be made by a qualied service
person and should conform to all local codes.
Guide
Model Features:
• 1/3” CMOS Sensor
• 900TVL Sensor imaging
• Day/Night / ICR
• Programming via OSD
• BNC Video Output
• Standard 12VDC Operation lower power
• Super ux IR LED for night vision
• 3D Noise reduction
Solution General Specications
General
Power source Regulated 12VDC
Power Consumption 100mA IR LED
IR LED On Power 10pcs Max 275mA 15pcs Max 320mA
Scanning system Progressive Scan Sensor
Scanning frequency NTSC 15.734KHz( H), 59.95Hz (V) / PAL 15.625KHz (H), 50Hz (V)
Effective Pixels 1305(h) x 1049(V)
Resolution 900TVL
OSD Control Optional Control via cable (see OSD Menu Page 7-8)
ACG / BLC On
Noise Reduction 2d/ 3d Enabled
Sync System Internal
Min. Illumination 0.01 Lux (AGC On, IE Off) / 0 Lux with IR LED On
Video output 1.0 Vp-p (75Ω , composite)
S/N Ratio More than 52dB (AGC OFF)
Video output BNC Connector 1.0Vp-p PAL / NTSC
Lens mount Fixed mount
Lens Matching for each model.
Operating temperature -10°C ~ +50°C / -40°F ~ 122°F
Operating humidity 0-90% (non-condensing)
*Specicaons subjected to change without prior noce.
1 2
NOTE: Make sure you don’t have any missing parts before you make the installation.
Incorrect installation could void the warranty if instructions are not followed correctly.
Please call technical for assistance if you are unsure about any procedures.
Identication
Mechanical Drawing
Installation
Installation information (General overview)
194 mm
7 5/8 in
226 mm
62 mm
2 3/8 in
1
2
Locking Screw
8 7/8 in
43
3 in
77 mm
5 6
Rotation lock
Accessories
1 Remove visor from camera to aid simpler installation. (Optional requirement)
2 Use drill template (D) as to guide to drill and attach camera to surface as required.
Holes on bracket are 120 degree apart, so three holes are required.
3 With camera attached you can now connect power, check device working.
(A) Wall Plugs
S7 x 26mm 3pcs
3 4
(B) Fitting Screws
PA4 x 24mm 3pcs
(C) L-Hex tool
54x18mm
(D ) Drill template
4 Using the (C) L-Hex tool you position left-right up/down and lock into place.
The rear position rotation allows turning of angle turn anti-clockwise to loosen.
5 Adjust zoom & focus using small at blade. (Vari-focal model only)
6 Replace the sun visor if removed from step 1.
Check IR LEDs are working by covering the photocell of camera, the IR LEDs will
give a faint red glow.
(Don’t look at IR LEDs for long periods of time, as you could damage your eyes)
4
NOTE: Make sure you don’t have any missing parts before you make the installation.
Incorrect installation could void the warranty if instructions are not followed correctly.
Please call technical for assistance if you are unsure about any procedures.
Identication
Mechanical Drawing
Installation
Installation information (General overview)
99 mm
3 7/8 in
1/2”
1
118 mm
4 5/8 in
2
Vari-Focal Lens Model
43
4 5/8 in
117.5 mm
5 6
152 mm
6 in
1 Use supplied template to drill holes for (A) plugs.
Accessories
(A) Wall Plugs
S7 x 26mm 3pcs
5 6
(B) Fitting Screws
PA4 x 24mm 3pcs
(C) L-Hex tool
58x20mm
(D ) Drill template
2 Remove locking cover using supplied (C) L-key. Optional requirement
3 Attach base part to surface with (B) screws. Use conduit if required.
4 Re-attach Cover and position camera then lock cover screws with L-Key.
5 Adjust the zoom & focus using at blade tool. (Vari-Focal models only)
6 Connect power, feeding through conduit may require this stage to be
completed before adjustment is made. Check IR LEDs are working by
covering the photocell of camera, the IR LEDs will give a faint red glow.
(Don’t look at IR LEDs for long periods of time, as you could damage your eyes)
6
CAMERA ADJUSTMENT (option) CAMERA ADJUSTMENT (option)
The OSD control may differ from show above, OSD buttons
may replace the joystick type. Service cable output maybe
not be available, and maybe optionally supplied with the
product.
MENU TREE SUMMARY
MAINMENU
IMAGE • 3D-NR • ON • OFF
• AE MODE • CENTER • CENTER WEIGHT
• BACK LIGHT • FRONT LIGHT
• WB • AWB-TEMPORAL • AWB-AI • AWB-SZ
• AWB-GW • AWB-CCT • AWB-PEO
• IMAGE ENHANCE
• SHARPNESS • DETAIL • EDGE
• CONTRAST • AUTO • MANUAL
• SATURATION • AUTO • MANUAL 0-15
• MIRROR • FLIP • BRIGHTNESS • ZOOM IN
DAY&NIGHT • AUTO • EXT • BLACK&WHITE • COLOR
ZONE MASK • COLOR • AREA NO.0 - AERA NO.7
• ZONE MASKING
• COLOR • AREA NO.0 - AERA NO.7
• STATUS HORIZON SIZE • VERTICAL SIZE
• HORIZON MOVE • VERTICAL MOVE
MOTION DETECTION• SENSITIVITY • AREA NO.0 - AERA NO.3
• ZONE MASKING
• STATUS •COLOR • HORIZON SIZE • VERTICAL SIZE
• HORIZON MOVE • VERTICAL MOVE
VIDEO STANDARD • PAL • NTSC
LANGUAGE • ENGLISH • CHINESE
LOAD DEFAULT
SOFT VERSION
SAVE&EXIT
EXIT
Highlight boxes below shows the menu path. Value ranges given
in menu below are a guide for setting ranges, the camera osd will
show only single values.
MAINMENU
IMAGE
DAY&NIGHT AUTO
ZONE MASK
MOTION DETECTION
VIDEO STANDARD PAL
LANGUAGE ENGLISH
LOAD DEFAULT
SOFT VERSION
SAVE&EXIT
EXIT
MAINMENU
IMAGE
DAY&NIGHT AUTO
ZONE MASK
MOTION DETECTION
VIDEO STANDARD PAL
LANGUAGE ENGLISH
LOAD DEFAULT
SOFT VERSION
SAVE&EXIT
EXIT
ZONE MASKING
COLOR MAGENTA
AREA NO.0
AREA NO.1
AREA NO.2
AREA NO.3
AREA NO.4
AREA NO.5
AREA NO.6
AREA NO.7
RETURN
ZONE MASKING
STATUS OFF
HORIZON SIZE 0~1280
VERTICAL SIZE 0~720
HORIZON MOVE 0~1280
VERTICAL MOVE 0~720
RETURN
IMAGE
3D-NR ON
AE MODE GLOBAL
WB AWB-TEMPORAL
IMAGE ENHANCE
MIRROR OFF
FLIP OFF
BRIGHTNESS 0~250
ZOOM IN 0~5
RETURN
MAINMENU
IMAGE
DAY&NIGHT AUTO
ZONE MASK
MOTION DETECTION
VIDEO STANDARD PAL
LANGUAGE ENGLISH
LOAD DEFAULT
SOFT VERSION
SAVE&EXIT
EXIT
MOTION DETECTION
SENSITIVITY HIGH
AREA NO.0
AREA NO.1
AREA NO.2
AREA NO.3
RETURN
MOTION DETECTION
STATUS OFF
COLOR WHITE
HORIZON SIZE 0~1280
VERTICAL SIZE 0~720
HORIZON MOVE 0~1280
VERTICAL MOVE 0~720
RETURN
IMAGE ENHANCE
SHARPNESS
CONTRAST
SATURATION
RETURN
SHARPNESS
DETAIL MANUAL
VALUE 0~15
EDGE MANUAL
VALUE 0~15
RETURN
CONTRAST
CONTRAST MANUAL
VALUE 0~255
RETURN
SATURATION
SATURATION MANUAL
VALUE 0~15
RETURN
7 8
TROUBLE SHOOTING NOTES
Follow the steps below if you are experiencing trouble with your
camera, before you contact your Technical Support.
• Nothing appears on the screen.
¤ Check that the power cable is connected properly and that the voltage is correct.
¤ Check that you have properly connected VIDEO cable to the camera VIDEO output jack and to the
monitor/DVR.
• The image on the screen is unclear.
¤ Is the lens or dome cover stained with dirt? Clean lens or dome cover with soft, clean cloth.
¤ Re-position the camera if necessary.
¤ Adjust the Zoom and Focus screws as needed.
• The image on the screen is dark.
¤ If you have an intermediate device, set the impedance to 75Ω / Hi-z.
¤ Adjust the monitor contrast & brightness controls.
• Image quality is poor.
¤ Be sure to check cable for and braid which may be touching the common Coaxial core pin.
¤ Verify that the camera is receiving sufcient power.
• There is interference in the image.
¤ The camera or the cables may be close to a source of high voltage, such as a generator. Re-position
the camera if necessary.
When the resistance value of copper wire is at [20˚C(68˚F)]
Copper wire size (AWG) #24(0.22mm) #22(0.33mm) #20(0.52mm) #18(0.83mm)
Resistance (Ω/m) 0.078 0.050 0.030 0.018
Voltage Drop (V/m) 0.028 0.018 0.011 0.006
As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively
long adapter output line for connection to the camera may affect the performance of the camera.
*Standard voltage for camera operation : DC12V ±10% or
*There may be some deviation in voltage drop depending on the type of wire and the manufacturer.
• Be sure to connect power only after all the installation is complete.
• Use the UL listed, CLASS 2 power transformer for 12v DC adapter.
9 10
Loading...