VF1600 EP
User Manual
Caution: Fog machines may set off smoke alarms!
©2023 Eliminator Lighting all rights reserved. Information, specications, diagrams, images, and in-
structions herein are subject to change without notice. Eliminator logo and identifying product names
and numbers herein are trademarks of Eliminator Lighting. Copyright protection claimed includes all
forms and matters of copyrightable materials and information now allowed by statutory or judicial law
or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of their respective companies and are hereby acknowledged. All non-Eliminator brands and
product names are trademarks or registered trademarks of their respective companies.
Eliminator Lighting and all afliated companies hereby disclaim any and all liabilities for property,
equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as a
result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and opera-tion
of this product.
Eliminator Lighting
6122 S. Eastern Ave. Los Angeles, CA. 90040
323-582-2650 | Fax 323-532-2941 | www.adj.com | info@adj.com
ADJ SUPPLY Europe B.V
Junostraat 2 6468 EW Kerkrade, The Netherlands
+31 (0)45 546 85 00 | Fax +31 45 546 85 99
www.adj.eu | info@adj.eu
ADJ PRODUCTS GROUP Mexico
AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
+52 (728) 282-7070
DOCUMENT VERSION
Due to additional product features and/or enhancements, an updated version of this
document may be available online.
Please check www.adj.com for the latest revision/update of this manual before
beginning installation and/or programming.
Date
11/01/23 1.0 N/A 1 Ch Initial release
Document
Version
Software
Version >
DMX Channel Mode Notes
2
CONTENTS
General Information 4
Limited Warranty (USA Only) 5
Warranty Registration | Features 6
Safety Guidelines 7
Overview 8
Installation Guidelines 9
DMX Setup 12
DMX Traits 14
Remote Operation 15
Fuse Replacement | Storage and Maintenance | Trouble Shooting 17
Dimensional Drawings 18
Specications 19
3
GENERAL INFORMATION
INTRODUCTION
Congratulations on your purchase of one of the most reliable fog machines on the market today!
The VF1600 EP commercial fog machine has been designed to perform reliably for years when the
guidelines in this booklet are followed. Please read and understand the instructions in this manual
carefully and thoroughly before attempting to operate this unit. These instructions contain important
information regarding safety during usage and maintenance.
CUSTOMER SUPPORT
Tel: (323) 213-4592 | Fax: (323) 582-2941
www.adj.com | support@eliminatorlighting.com
Warning! To prevent or reduce the risk of electrical shock or re, do not expose this unit to rain or moisture.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, as doing
so will void your manufacturer’s warranty. In the event that your unit requires service, please contact Elimi-
nator Lighting for assistance.
SAFETY NOTICE! NEVER POINT OR AIM A FOG MACHINE TOWARDS PEOPLE OR THEIR CLOTHING. THIS UNIT EMITS HOT VAPOR AND SHOULD BE USED WITH THE SAME CARE THAT WOULD
BE OBSERVED WHEN USING AN ELECTRIC KETTLE OR AN IRON.
PLEASE recycle the shipping carton whenever possible.
4
LIMITED WARRANTY (USA ONLY)
A. Eliminator Lighting, an ADJ Products, LLC brand, hereby warrants, to the original purchaser, Eliminator
Lighting products to be free of manufacturing defects in material and workmanship for a prescribed
period from the date of purchase (see specic warranty period on reverse). This warranty shall be
valid only if the product is purchased within the United States of America, including possessions and
territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable
evidence, at the time service is sought.
B. For warranty service, you must obtain a Return Authorization number (RA#) before sending back the
product-please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the Eliminator Lighting factory. All shipping charges must be pre-paid. If the requested repairs
or service (including parts replacement) are within the terms of this warranty, Eliminator Lighting
will pay return shipping charges only to a designated point within the United States. If the entire
instrument is sent, it must be shipped in its original package. No accessories should be shipped
with the product. If any accessories are shipped with the product, Eliminator Lighting shall have no
liability whatsoever for loss of or damage to any such accessories, or for the safe return thereof.
C. This warranty is void of the serial number has been altered or removed; if the product is modied
in any manner which Eliminator Lighting concludes, after inspection, affects the reliability of the
product, if the product has been repaired or service by anyone other than ADJ Products, LLC factory
unless prior written authorization was issued to purchaser by Eliminator Lighting; if the product is
damaged because not properly maintained as set forth in the instruction manual.
D. This is not a service contact, and this warranty does not include maintenance, cleaning or periodic
check up. During the period specied above, Eliminator Lighting will replace defective parts at
its expense with new or refurbished parts, and will absorb all expenses for warrant service and
repair labor by reason of defects in material or workmanship. The sole responsibility of Eliminator
Lighting under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of Eliminator Lighting. All products covered by this warranty
were manufactured after August 15, 2012, and bear identifying marks to that effect.
E. Eliminator Lighting reserves the right to make changes in design and/or improvements upon its
products without any obligation to include these changes in any products theretofore manufactured.
F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied
with products described above. Except to the extent prohibited by applicable law, all implied warranties
made by Eliminator Lighting in connection with this product, including warranties of merchantability
or tness, are limited in duration to the warranty period set forth above. And no warranties, whether
expressed or implied, including warranties of merchantability or tness, shall apply to this product
after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or
replacement as is expressly provided above; and under no circumstances shall Eliminator Lighting
be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use,
this product.
G. This warranty is the only written warranty applicable to Eliminator Lighting products and supersedes
all prior warranties and written descriptions of warranty terms and conditions heretofore published.
LIMITED WARRANTY PERIODS
• All Eliminator Lighting products (except laser diodes) = 1-year (365 days) Limited Warranty
(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)
• Laser Products = 1 Year (365 Days) Limited Warranty (excludes laser diodes which have 6
month limited warranty)
• Batteries = 180 Day Limited Warranty (excluding batteries which have a 180 day limited warranty)
5
WARRANTY REGISTRATION
This device carries a one year (365 days) limited warranty. Please fill out the enclosed warranty card
to validate your purchase. All returned service items, whether under warranty or not, must be freight
pre-paid and accompanied by a return authorization (R.A.) number. The R.A. number must be clearly
written on the outside of the return package. A brief description of the problem as well as the R.A. num-
ber must also be written down on a piece of paper included in the shipping carton. If the unit is under
warranty, you must provide a copy of your proof of purchase invoice. You may obtain a R.A. number by
contacting our customer support team on our customer support number. All packages returned to the
service department not displaying a R.A. number on the outside of the package will be returned to the
shipper.
FEATURES
• Special heating element designed to prevent excessive particle buildup
• Wide-angle spray nozzle
• Long-life pump
• High performance fogging output
• Removable remote control included
• DMX control
6
SAFETY GUIDELINES
• In the event that the device needs to be return to Eliminator Lighting for service, use only the original
packaging and materials for shipping.
• To reduce the risk of electrical shock or re, do not expose this unit rain or moisture.
• Do not spill water or other liquids into or on to your unit.
• Ensure that the fog uid is poured only into the uid reservoir. Avoid spilling fog uid into or onto
other internal components.
• Ensure that the voltage of the power source matches the required voltage of the device.
• Do not remove the cover for any reason! There are no user serviceable parts inside this device.
• Disconnect the unit from power during long periods of non-use.
• Never operate this unit with the cover removed.
• Do not attempt to operate this unit if the power cord has been frayed or broken.
• Do not attempt to remove or break off the ground prong from the electrical cord. This prong is used
to reduce the risk of electrical shock and re in the event of an internal short.
• Disconnect from main power before attempting to make any type of connection.
• Never block the ventilation holes, and always be sure to mount this unit in an area that will allow
proper ventilation. Allow at least 6” (15cm) clearance between this device and a wall.
• This unit is intended for indoor use only, and use of this product outdoors voids all warranties.
• Follow proper storage guidelines when storing for extended periods. See the Proper Storage and
Maintenance section of this manual for details.
• Always mount this unit in a safe and stable manner.
• Always route your power cord out of the path of foot trafc. Power cords should be routed so that
they are not likely to be walked on or pinched by items placed upon or against them.
• The xture should be serviced by qualied service personnel when:
A. The power-supply cord or the plug has been damaged.
B. Objects have fallen onto, or liquid has been spilled into, the unit.
C. The unit has been exposed to rain or water.
D. The unit does not appear to operate normally or exhibits a marked change in performance.
7
OVERVIEW
Fluid
Level
Mounting
Bracket
Window
Bracket
Adjustment
Knob
Power
Safety
Cable
Loop
Nozzle
Fluid
Reservoir
DMX In
(behind
handle)
DMX
Out
Dip
Switches
Switch
Manual
Input
Fog
Button
Wireless
Power
Port
Input
Fuse
10A @ 230V
15A @ 120V
8
INSTALLATION GUIDELINES
ELECTRICAL CONNECTIONS
A qualied electrician should be used for all electrical connections and/or
installations.
DO NOT INSTALL THE FIXTURE IF YOU ARE NOT QUALIFIED TO DO SO!
Fixture MUST be installed following all local, national, and country commercial electrical and construction
codes and regulations. Before rigging/mounting the xture to any metal truss/structure or placing the
xture on any surface, a professional equipment installer MUST be consulted to determine if the metal
truss/structure or surface is properly certied to safely hold the combined weight of the xture, clamps,
cables, and accessories.
Overhead xture installation must always be secured with a secondary safety attachment, such as an
appropriately rated safety cable that meets all local, national, and country codes and regulations.
Fixture should be installed away from walking paths, seating areas, or areas where unauthorized
personnel might reach the xture by hand.
NEVER stand directly below the xture when rigging, removing, or servicing.
If the unit is installed in a suspended or hanging conguration, it should be mounted using a mounting
clamp (not provided), and afxing it to the mounting bracket that is provided with the unit. Always
ensure that the unit is rmly xed to avoid vibration and slipping during operation. Always ensure that
the structure that you are attaching the unit to is secure and is able to support at least 10 times the
unit’s weight. Also, always use a safety cable that can hold 12 times the unit’s weight when installing
the xture. The equipment must be installed by a professional, and it must be installed in a place where
it is out of the reach of people’s grasp.
GENERAL SET UP
1. Open the shipping carton and carefully remove the unit from the shipping carton. Remove all the
packing material from the device, paying special attention to the area around the nozzle.
2. Set the fog machine on a at, dry surface. Locate the included bracket from the package and attach
it to the sides of the fog machine using the supplied hardware. Please note: The bracket is an
optional accessory, and its usage is required when the fog machine is being installed in a
suspended or hanging conguration.
3. Fill the fog uid reservoir with ADJ brand fog juice only and then tighten the cap.
4. Firmly attach the remote control unit to the remote control socket on the rear of the unit.
5. Plug the unit in to a compatible power supply. At this time, the uid reservoir will glow red, indicating
that the unit is warming up. Allow approximately eight minutes for the fogger to reach normal
operating temperature. When it has reached sufcient temperature, the reservoir will glow green to
indicate that the device is ready to emit fog.
6. To emit fog, either press the remote button, use the timer function, or use the manual button on the
rear of the unit. See the Timer Remote Operation section of this manual for operating instructions.
9
INSTALLATION GUIDELINES
CLAMP MOUNTING
To install this device in a suspended environment, insert a bolt of the proper weight rating through
the bottom of an appropriately rated mounting clamp as well as the mounting surface of the mounting
bracket, then fasten in place with a bolt of the appropriate rating. When installing this device suspended
from a truss, make sure that the device hangs in a level position in order to prevent leakage from the
uid reservoir. Be sure this xture is kept at least 0.2m (7.9in.) away from any ammable materials
(decoration etc.). This device also includes a safety cable attachment point on the top surface, near the
uid reservoir cap. Always use and install a properly rated supplied safety cable as a safety measure
to prevent accidental damage and/or injury in the event the clamp fails. Never use the carrying handles
for secondary attachment.
MOUNTING
CLAMP
MOUNTING
BRACKET
SAFETY
CABLE
LOOP
ALWAYS ATTACH A SAFETY CABLE WHENEVER INSTALLING THIS FIXTURE IN
A SUSPENDED ENVIRONMENT TO ENSURE THE FIXTURE WILL NOT FALL IF
THE CLAMP FAILS.
10
INSTALLATION GUIDELINES
RIGGING
Overhead rigging requires extensive experience, including but not limited to: calculating working
load limits, understanding the installation material being used, and periodic safety inspection of all
installation material and the fixture itself. If you lack these qualifications, do not attempt to perform the
installation yourself. Improper installation can result in bodily injury.
FIXTURE INSTALLATION
This device is fully operational in two different mounting positions: hanging in a level position from a
truss, or set on a at level surface. Regardless of conguration, the device should be in a level
position in order to prevent leakage from the uid reservoir. Be sure this xture is kept at least
0.2m (7.9in.) away from any ammable materials (decoration etc.). Always use and install the supplied
safety cable as a safety measure to prevent accidental damage and/or injury in the event the clamp
fails. Never use the carrying handles for secondary attachment.
FALLING FIXTURES CAN CAUSE SEVERE INJURY OR SERIOUS EQUIPMENT
DAMAGE! FOR THIS REASON, FIXTURES SHOULD BE INSTALLED AND INSPECTED
ONLY BY QUALIFIED PERSONNEL. DO NOT INSTALL THE UNIT IF YOU LACK THE
QUALIFICATIONS TO DO SO, OR IF YOU HAVE DOUBTS ABOUT THE SAFETY AND
SECURITY OF THE INSTALLATION SETUP OR LOCATION!
11
DMX SETUP
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol that is used as a form of
communication between intelligent xtures and controllers. A DMX controller sends DMX data instructions from the controller to the xture. DMX data is sent as serial data that travels from xture to
xture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX xtures (most controllers
only have a DATA “OUT” terminal).
DMX Linking: DMX is a language allowing all makes and models of different manufacturers to be
linked together and operate from a single controller, as long as all xtures and the controller are
DMX compliant. To ensure proper DMX data transmission, try to use the shortest cable path possible
when linking several DMX xtures together. The order in which xtures are connected in a DMX line
does not inuence the DMX addressing. For example, a xture assigned a DMX address of 1 may
be placed anywhere in a DMX line: at the beginning, at the end, or anywhere in the middle. When a
xture is assigned a DMX address of 1, the DMX controller knows to send DATA assigned to address
1 to that unit, no matter where it is located in the DMX chain.
Data Cable (DMX Cable) Requirements (For DMX Operation): This device can be controlled via
DMX-512 protocol, and is a 1-channel DMX unit. The DMX address is set using the dip switches on
the back panel of the unit. Your unit and your DMX controller require an approved DMX-512 110-ohm
data cable for data input and output (Figure 1). We recommend Accu-Cable DMX cables. If you are
making your own cables, be sure to use standard 110-120 Ohm shielded cable (This cable may be
purchased at almost all professional lighting stores). Your cables should be made with a male XLR
connector at one end and a female XLR connector at the other. Also remember that DMX cable must
be daisy chained and cannot be split.
12
DMX SETUP
Notice: Be sure to follow gures two and three when making your own cables. Do not use the ground
lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the
shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a
short circuit and erratic behavior.
Special Note: Line Termination. When longer runs of cable are used, you may need to use a termi-
nator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which
is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable
terminator (ADJ part number Z-DMX/T) will decrease the chances of erratic behavior.
5-Pin XLR DMX Connectors. Some manufacturers use 5-pin DMX-512 data cables for DATA transmission in place of 3-pin. 5-pin DMX xtures may be implemented in a 3-pin DMX line by using a
cable adapter, which can readily be found at most electronics stores. The chart below details a proper
cable conversion.
13
DMX TRAITS
This device features a single DMX channel to control fog output. This allows you to control each individual fixture’s traits with a standard DMX 512 controller.
1. To run your fixture in DMX mode, set the DMX address using the dipswitches located on the rear
panel of the unit.
2. Connect the fixture to any standard DMX controller using the fixture’s XLR connectors. Follow the
set-up specifications that come with your DMX controller.
CHANNEL
1
DMX
VALUES
000 No Fog
001 - 255 Fog Output, 0% to 100%
FUNCTION
Fog Output
14
REMOTE OPERATION
Always be sure to maintain an adequate supply of fog juice in the uid reservoir. Running the
fog machine dry will result in pump failure and/or clogging, and is the most common cause of
failure in fog and haze machines. We recommend use of ADJ brand fog juice only!
VFTR Timer Remote: Connect the remote to the fog machine, using the “Manual Input” port.
WIRED REMOTE
PORT
The remote features three (3) L.E.D.s that illuminate to indicate different functions.
• The YELLOW LED on the left indicates that the timer is turned on and is activated. The timer func-
tion allows fog to be emitted at designated intervals. Please note that the timer function is inactive
when DMX mode is activated.
• The RED LED indicates that continuous fogging is active.
• The GREEN LED on the right is for manual fogging. Wait for the GREEN LED to light up, then
press the button for manual fogging.
The remote also features three rotary knobs:
• The Duration knob sets the timer duration (Length of fog output).
• The Interval knob sets the fog output intervals (Length of time between fog output bursts).
• The Output knob sets the amount of fog the machine will output.
Caution: Disconnect the device from power before removing or replacing the remote control
unit.
15
REMOTE OPERATION
VFWR2 Wireless Remote Control: This device can also be operated by wireless remote. Plug the
receiver box into the wireless input, and locate the four numbered dip switches on the side of the
receiver. Se-lect any dip switch and ip it to the ON position. The numbered button on the remote that
corresponds to the selected dip switch will now control fog output. For example, if dip switch #3 is set
to the ON position, then button 3 on the wireless remote will control fog output.
WIRELESS
RECEIVER PORT
DIP
SWITCHES
WIRELESS INSTALLATION GUIDELINES
For best results, position the xture so that the display screen is oriented in the direction of the transmitter
device or remote. Wireless signal can penetrate walls, glass, metal, and most objects. However, there
are many factors that can effect and/or interrupt the wireless signal, including the presence of people.
Therefore, it is highly recommended to position the wireless antenna a minimum of 9.8ft (3m) above
audiences to ensure optimum and reliable wireless operation.
16
FUSE REPLACEMENT
Disconnect the unit from its power source. Remove the power cord from the unit, then nd the fuse
holder located inside the power socket. Insert a at-head screw driver into the power socket and gently
pry out the fuse holder. Remove the bad fuse and replace with a new one of the same rating (10A for
230V power, or 15A for 120V power). Please note that the fuse holder also has a holder for a spare
fuse.
STORAGE AND MAINTENANCE
Store your device in a cool area only, and cover the device to prevent dust buildup. When storing for
long periods of time, it is strongly advised to run the device at least once every 3-4 months, due to the
fact that long periods of inactivity can severely shorten the operational life of the device. Only run water
based fog juice through your device. Never run plain water, vinegar, or any other liquid solution through
your device, as running anything other then water based fog juice will seriously damage your device.
TROUBLE SHOOTING
If you experience low fog output, pump noise, or no fog output at all, disconnect the device from power
and discontinue use immediately. Do not continue to push the remote control’s activation button, as
this may cause damage to the device. Check uid level, the external fuse or breaker, and remote con-
nection, and verify that the wall outlet is sending power. If none of these factors prove to be the cause
of the problem, and the unit still fails to operate correctly, the unit may require service. Please contact
customer support for further instructions. Please do not return the unit to your dealer without contacting
customer support rst.
17
DIMENSIONAL DRAWINGS
510mm(20.08in)
293mm(11.54in)
187mm(7.36in)
146mm(5.75in)
262mm(10.31in)
324mm(12.76in)
18
SPECIFICATIONS
• 1500W mobile DMX Fog Machine
• High efciency heater block burns through fog with less residue
• Electronic Thermo Sensing (ETS) for optimum heating levels
• LED heating indicator system in tank: Red = Heating; Green = Ready to use; Flashing = Fog uid tank is
low
• Low fog uid shut off sensor to protect pump
• Warm-up time: 8 minutes
• Reheating Time: 15 Seconds
• Second Fog Shooting Time: Around 12 Seconds
• Output: 20,000 cubic ft. per min
• Fog uid tank: 2.3 Liter (non-removable)
• Includes Eliminator VFWR2 wireless remote control
• Includes Eliminator VFTR wired timer remote control
• Fog output switch on rear panel
• 3-pin DMX In/Out
• Safety Loop
• Only use high quality, water-based fog uid
• Dimensions (LxWxH): 20.8” x 12.76” x 11.54” / 510mm x 324mm x 293mm
• Weight: 22 lbs. / 10 kg.
19
Loading...