STEALTH WASH
ZOOM
Introduction:
The Stealth Wash Zoom is a unique DMX intelligent moving head unit. The Stealth Wash Zoom has
3 operating modes; sound active mode, show mode, or controlled via DMX controller. The Stealth
Wash Zoom has 2 DMX Channel modes; 5 or 16 channels. The unit can be run as a stand alone unit
or in a Master/Slave set up. This unit has been tested and there is no assembly required. Follow the
instructions on the following pages to operate your fixture. To enhance the beams effects you can
use a fog machine.
CAUTION! Please read and understand these instructions before installing or operating this unit.
CAUTION! Please read and
understand these instructions
before installing or operating
this unit.
Fuse Replacement: Locate and remove
the unit’s power cord. Once the cord
has been removed, the fuse holder is
located inside the power socket. Insert
a flat-head screw driver into the fuse
holder and gently pry out the holder.
Remove the bad fuse and replace with
a new one. The fuse holder has a built-in
second holder for a spare fuse.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
SPECIFICATIONS:
Model: Stealth Wash Zoom
Supply Voltage: 100V-240V 50/60Hz
LED: 7 x 12W RGBW LED’s
Weight: 10lbs./ 4.5 kgs.
Size: 6.22” (L) x 9.4” (W) x 12.63” (H)
Fuse: 2 Amp
Power Consumption: 85W
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 2 DMX Channel Modes:
5 Channel Mode &
16 Channel Mode
Colors: RGBW
Warranty: 1 Year
AXXX: In this menu you can set the DMX address. Press the Up or Down buttons until “AXXX” is displayed. “XXX” is the current displayed DMX address. Press Enter and use the UP or Down buttons to
nd your desired address. When you have found your desired address press the Enter button to set
it.
CHNd: The Stealth Wash Zoom has 2 DMX channel modes; 5 channel mode and 16 channel mode.
In this menu you can select your desired channel mode. Press the Up or Down buttons until “CHNd” is displayed and press ENTER. Either “16CH” or “5CH” will be displayed. Use the Up and Down buttons
to toggle between the two modes and press Enter to make your selection and press Menu to exit.
SPNd (Sound Active Speed): In this menu you can adjust the sound active moving speed. Press
the Up or Down buttons until “SPNd” is displayed and press ENTER. Either “Low” (Low Speed) or
“High” (High Speed) will be displayed. Use the Up and Down buttons to toggle between the two
speeds and press Enter to make your selection. Press the Menu button to exit.
SLNd (Master/Slave): In this menu you can designate the xture as either a Master or Slave in a
master-slave set up. Press the Up or Down buttons until “SLNd” is displayed and press Enter. Either
“Mast” or “SL 1 will be displayed. Use the Up and Down buttons to nd your desired setting and
press Enter to make your selection. Press the Menu button to exit
SHNd (Show Mode): In this menu you can activate 1 of the 8 show mode’s. Press the Up or Down
buttons until “SHNd” is displayed and press Enter. 1 of 8 shows will be displayed. Use the Up and
Down buttons nd your desired show and press Enter to make your selection. Press the Menu button
to exit
Soun (Sound Active): In this menu you can activate Sound Active mode. Press the Up or Down buttons
until “Soun” is displayed and press Enter. Either “On” or “O” will be displayed. Use the Up and
Down buttons toggle between the choices and press Enter to make your selection. Press the Menu
button to exit.
PAn (Reverse Pan): In this menu you can reverse the Pan function. Press the Up or Down buttons
until “PAn” is displayed and press Enter. Press the Up or Downs buttons until “On” is displayed, and
press Enter. Press the Menu button to exit. This function works better when you have two units connected in a Master/Slave setup. Have one unit set to reverse Pan and the other unit in normal Pan.
tIL ( Reverse Tilt): In this menu you can reverse the Tilt function. Press the Up or Down buttons until
“tIL” is displayed and press Enter. Press the Up or Downs buttons until “On” is displayed, and press
Enter. Press the Menu button to exit. This function works better when you have two units connected
in a Master/Slave setup. Have one unit set to reverse Tilt and the other unit in normal Tilt.
dISP (Display): In this menu you can “ip” the display 180°. Press the Up or Down buttons until
“dISP” is displayed and press Enter. Either “ON” or “OFF” will now be displayed. If you want to “ip”
the display press the Up button so that “ON” is displayed, and press Enter. Press the Menu button to
exit.
rFAC (Default Setting): In this menu you can reset the unit to it default settings. Press the Up or
Down buttons until “rFAC” is displayed and press Enter. Select “On” and press Enter to revert to
default settings. Press the Menu button to exit without any changes.
rSt (Reset): In this menu you can activate reset function. Press the Press the Up of Down buttons
until “rSt” is displayed and press Enter. The unit will now begin to reset. Press the Menu button to
exit.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Ad t (OFFSET MENU) -
To enter the Oset Menu, press the Up or Down buttons until “Ad t” is displayed and press Enter. “P000” will
now be displayed. Press the Up button so that the display reads “P018” and press Enter. In this submenu you
are able to adjust the home positions of the pan and tilt motor’s, and focus motor. If you select delete, it will
reset all home positions to “0000”. Press the Menu button to exit.
Ad t:
(Delt) - Selecting this will default all oset values to “0000”.
(P) - Use the Up and Down buttons to adjust the oset of the Pan motor.
(t) - Use the Up and Down buttons to adjust the oset of the Tilt motor.
(F) - Use the Up and Down buttons to adjust the oset of the Focus motor.
OPERATION:
UNIVERSAL DMX CONTROL: This unit allows you to use any universal DMX-512 controller to control head
movement, LED colors, and the shutter (strobe). A DMX controller allows you to create unique programs tailored to your individual needs. Follow the set-up specifications that are included with your DMX controller.
1. The Stealth Wash Zoom has two DMX channel modes; 5 DMX channels and 16 DMX channels.
2. Press the Up or Down buttons until “Chnd” is displayed, and press Enter.
3. Press the Up or Down buttons until your desired DMX channel mode is displayed, and press Enter.
4. Press the Mode button until “AXXX” is displayed. “XXX” is the current displayed DMX addess.
Press the Enter button.
4. Use the Up and Down buttons to find your desired address and press Enter.
5. Connect your DMX Controller and use the controller’s faders to control the various DMX fixture traits.
6. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.
7. For help operating in DMX mode consult the manual included with your DMX controller.
SOUND ACTIVE MODE:
1. To activate Sound Active mode, press the Up or Down buttons until “SOUN” is displayed, and press Enter.
2. Either “On” or “Off” will be displayed. To activate sound active mode press the Up or Down buttons until
“On” is displayed, and press Enter to select. Press the Menu button to exit
3. To adjust the movement speed in sound active mode press the Up or Down buttons until “SPnd” is
displayed. Either “HISP” (High Speed) or “LoSP” (Low Speed) will be displayed. Use the Up or Down
buttons to switch between the two modes and press Enter to make your selection. Press the Menu button
to exit.
SHOW MODE:
1. To activate Show mode, press the Up or Down buttons until “SHnd” is displayed, and press Enter.
2. 1 of 8 shows will be displayed. Use the Up or Down buttons to scroll through the shows and press Enter
to make your selection. Show 0 runs a random show. Press the Menu button to exit.
MASTER-SLAVE SET UP: This function will allow you to link up to 16 units together and operate without a
controller. The units can be sound active or in show mode. In a Master-Slave set up one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.
1. Using approved DMX data cables, daisy chain your units together via the XLR connector on the rear of the
units. Remember the Male XLR connector is the input and the Female XLR connector is the output. The
rst unit in the chain (master) will use the female XLR connector only - The last unit in the chain will use the
male XLR connector only. For longer cable runs we suggest a terminator at the last fixture.
2. On the Master unit press the Menu button until “SLnd” is displayed, and press Enter. Use the UP and
DOWN buttons to scroll to the “Mast” setting and press Enter. Press the Menu button to exit.
3. After setting the Master unit to the master setting find and set your desired operating mode.
4. On the slave units press the Menu button until “SLnd” is displayed, and press ENTER. Press the Up or
Down buttons until “SL 1” and press Enter. Press the Menu button to exit.
5. The slave units will now follow the Master unit.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
DMX TRAITS: 5 CHANNELS
CHANNEL 1: PAN
CHANNEL 2: TILT
CHANNEL 3: COLORS
0 - 5 = NOTHING
6 - 10 = RED
11 - 15 = GREEN
16 - 20 = BLUE
21 - 25 = WHITE
26 - 30 = RED + GREEN
31 - 35 = GREEN + BLUE
36 - 40 = BLUE + WHITE
41 - 45 = RED + BLUE
46 - 50 = GREEN + WHITE
51 - 55 = RED + WHITE
56 - 60 = RED + GREEN + BLUE
61 - 65 = RED + GREEN + WHITE
66 - 70 = GREEN + BLUE + WHITE
71 - 75 = RED + GREEN + BLUE + WHITE
76 - 127 = COLOR CHANGE SLOW - FAST
128 - 133 = NOTHING
134 - 255 = COLOR FADE SLOW - FAST
CHANNEL 4: INTERNAL PROGRAMS
0 - 20 = NOTHING
21 - 40 = PROGRAM 1
41 - 60 = PROGRAM 2
61 - 80 = PROGRAM 3
81 - 100 = PROGRAM 4
101 - 120 = PROGRAM 5
121 - 140 = PROGRAM 6
141 - 160 = PROGRAM 7
161 - 180 = PROGRAM 8
181 - 200 = NOTHING
201 - 225 = MOTOR RESET
226 - 255 = NOTHING
CHANNEL 5: FOCUS
0 - 255 = FOCUSING NARROW - WIDE
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
DMX TRAITS: 16 CHANNELS
CHANNEL 1: PAN
CHANNEL 2: PAN FINE
CHANNEL 3: TILT
CHANNEL 4: TILT FINE
CHANNEL 14: COLOR FADE
0 - 10 = NOTHING
11 - 194 = COLOR FADE SLOW - FAST
CHANNEL 15: PAN/TILT SPEED
0 - 255 = FAST - SLOW
CHANNEL 5: RED
0 - 255 = 0% - 100%
CHANNEL 6: GREEN
0 - 255 = 0% - 100%
CHANNEL 7: BLUE
0 - 255 = 0% - 100%
CHANNEL 8: WHITE
0 - 255 = 0% - 100%
CHANNEL 9: MASTER DIMMER
0 - 255 = 0% - 100%
CHANNEL 10: SHUTTER/STROBING
0 - 9 = SHUTTER CLOSED
10 - 245 = STROBING SLOW - FAST
246 - 255 = SHUTTER OPEN
CHANNEL 11: FOCUS
0 - 255 = FOCUSING NARROW - WIDE
CHANNEL 12: COLOR TEMPERATURES
0 - 255 = COLOR TEMPERATURES
CHANNEL 16: INTERNAL PROGRAMS
0 - 20 = NOTHING
21 - 40 = PROGRAM 1
41 - 60 = PROGRAM 2
61 - 80 = PROGRAM 3
81 - 100 = PROGRAM 4
101 - 120 = PROGRAM 5
121 - 140 = PROGRAM 6
141 - 160 = PROGRAM 7
161 - 180 = PROGRAM 8
181 - 200 = NOTHING
201 - 225 = MOTOR RESET
226 - 255 = NOTHING
CHANNEL 13: COLOR EFFECT
0 - 10 = NOTHING
11 - 20 = RED
21 - 30 = GREEN
31 - 40 = BLUE
41 - 50 = WHITE
51 - 60 = RED + GREEN
61 - 70 = GREEN + BLUE
71 - 80 = BLUE + WHITE
81 - 90 = RED + BLUE
91 - 100 = GREEN + WHITE
101 - 110 = RED + WHITE
111 - 120 = RED + GREEN + BLUE
121 - 130 = RED + GREEN + WHITE
131 - 140 = GREEN + BLUE + WHITE
141 - 150 = RED + GREEN + BLUE + WHITE
151 - 255 = COLOR CHANGE SLOW - FAST
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Screw one clamp (3) via a M12 screw and nut to the included bracket (1). Attach the bracket using
the provided screws to the bottom of the Stealth Wash Zoom. Attach the included eyehole screw (2)
to the bottom of the xture and and pull the safety-cable through eyehole screw and over the trussing system or a safe xation spot. Insert the end in the carabine and tighten the safety screw.
Dimesnional Drawings
9.4”/239mm
12.63”/321mm
6.7”/170mm
6.22”/158mm
1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our
1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with
dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover
items or parts prone to wear and tear: motors, fuses, brushes and belts. Eliminator Lighting warranty
is only valid with-in the United States.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Loading...