Eliminator Lighting Electro Panel 192 User Manual
Electro
Panel 192
SPECIFICATIONS:
Model: Electro Panel 192
LEDs
& 64 Blue
Weight: 4.6lbs./ 2.1kgs.
Size: 7.12” (H) x 12.41” (W) x
4.5” (D)
Fuse: 7 Amp
Supply Voltage: 120V
Power Cord Daisy Chain: 33 Fixtures Max.
Working Position:
Duty Cycle: None
DMX Channels: 6 DMX Channel Modes:
1, 2, 3, 4, 6, or 7 DMX
Channels
Colors: Multiple Colors
Warranty: 1 Year
: 192 - 64 Red, 64 Green,
Any Safe position
CAUTION! Please read and
understand these instructions
before installing or operating
this unit.
Operating Instructions:
The Electro Panel 192 has been tested at the factory, there is no assembly required. The unit is
ready to be plugged into a power outlet. This unit is a 7 channel DMX intelligent LED par can. It can
be run as a stand-alone, static unit DMX controlled unit, or in a Master/Slave configuration. While
in Stand Alone or a Master/Slave configuration, you can run the auto mode. For stand-alone mode,
and Master/Slave configuration settings, see other side.
Power Cord Daisy Chaining: With this feature you can connect the xtures to one another using the
IEC input and output sockets. The quantity that can be connected is 33 xtures maximum. After 33 xtures you will need to use a new power outlet. They must be the same xtures. DO NOT mix xtures.
1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our
1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with
dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover
items or parts prone to wear and tear: lamps, fuses, brushes and belts. Eliminator Lighting warranty
is only valid with-in the United States.
Caution! Never open unit when in use.
Always disconnect main power before
replacing fuse. Remember to always
replace with the exact same type fuse.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
ADDR - DMX Address Setting.
1. Tap the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER.
2. “1” will now be displayed and ashing. Press the UP or DOWN buttons to nd your desired
address. Press ENTER to set your desired DMX address.
CHND - There are 6 DMX Channel modes to choose from, this will let you switch and select
your DMX Channel mode. You can choose from either 1, 2, 3, 4, 6, or 7 DMX Channels. Please
see the last page of the DMX values and traits for each DMX Channel Mode.
1. Tap the either the MENU button until “CHND” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to scroll through the different DMX Channel modes. Once you have
found your desired DMX Channel mode press ENTER to conm and exit.
SLND - This will let you set unit as a master or slave in a master/slave conguration.
1. Tap the either the MENU button until “SLND” is displayed, press ENTER. “MSTR”, “SL 1” or “SL 2” will
be displayed.
2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to conm and
exit.
SHND - in this mode you can choose and run one of 11 preprogrammed shows.
1. Tap the either the MENU button until “SHND” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to scroll through 11 preprogrammed shows.
3. Select your desired show by pressing the ENTER button to conrm and exit.
DIMM - in this mode you can set the brightness/intensity of the xture.
1. Tap the either the MENU button until “DIMM” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to adjust the brightness (0-255). A setting of 0 will not produce any
light output
3. Select your desired intensity by pressing the ENTER button to conrm and exit.
STRO - in this mode you can activate and set the strobe rate.
1. Tap the either the MENU button until “STRO” is displayed, press ENTER.
2. Tap the UP or DOWN buttons to adjust the stobe rate (0-255). A setting of 0 will deactivate the
strobe feature.
3. Select your desired strobe rate by pressing the ENTER button to conrm and exit.
BLND - Blackout or Stand by mode.
1. Tap the either the MENU button until “BLND” is displayed, press ENTER. Either Yes or No will be
displayed.
©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com
Loading...