Eliminator Lighting Crystal Ray LED User Manual

Crystal Ray

LED

SPECIFICATIONS:

Model: Crystal Ray LED
LEDs: (28 Red, 28 Green, 28

Blue, & 28 White)

Weight: 4.6lbs./ 2.1kgs.
Size: 18” (L) x 13” (W) x

8.5” (H)

Fuse: 1 Amp
Supply Voltage: 100V-240V 50/60Hz
Working Position: Any Safe position
Duty Cycle: None
DMX Channels: 4
Colors: RGBW
Warranty: 1 Year

CAUTION! Please read and

understand these instructions
before installing or operating
this unit.

Operating Instructions:

The Crystal Ray LED has been tested at the factory, there is no assembly required. The unit is ready
to be plugged into a power outlet. This unit is a 4 channel DMX intelligent LED sweeping fixture. It
can be run as a stand-alone unit, DMX controlled unit, or in a Master/Slave configuration. While in
Stand Alone or a Master/Slave configuration, the auto mode and sound active mode will run togeth­er. The fixture will enter Auto Mode when sound is not present. For stand-alone mode, Master/Slave
configuration, and DMX Control see other side.

1 Year Limited Warranty: Eliminator Lighting warranty is valid from the date of purchase. Our

1 year limited warranty covers manufacturing defects only. Serial number, place of purchase with
dated valid receipt must be submitted at time of service. Eliminator Lighting warranty does not cover
items or parts prone to wear and tear: LEDs, fuses, brushes and belts. Eliminator Lighting warranty
is only valid with-in the United States.

Caution! Never open unit when in use.
Always disconnect main power before
replacing fuse. Remember to always
replace with the exact same type fuse.

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com

Stand Alone (Auto Mode and Sound Active mode):

1. Plug the fixture in and put dipswitches 1-9 & dipswitch F2 in the “Off” position, and put the F1 dipswitch
in the “On” position.

Universal DMX Control: This unit allows you to use any universal DMX-512 controller to control the different
DMX traits. A DMX controller allows you to create unique programs tailored to your individual needs.

1. The Crystal Ray LED uses four DMX channels.

2. To control your fixture in DMX mode, follow the set-up specifications that are included with your DMX con­ troller.

3. Set your desired DMX address using dipswitches 1-9.

4. Use the controller’s faders to control the various DMX fixture traits.

5. For longer cable runs (more than a 100 feet) use a terminator on the last fixture.

6. For help operating in DMX mode consult the manual included with your DMX controller.

Master-Slave Operation (Auto Mode or Sound Active): This function will allow you to link up to 16 units
together and operate without a controller. In Master-Slave operation one unit will act as the controlling unit and
the others will react to the controlling units operation. Any unit can act as a Master or as a Slave.

1. Using standard XLR microphone cables, daisy chain your units together via the XLR connector on the rear
of the units. Remember the Male XLR connector is the input and the Female XLR connector is the output.
For longer cable runs we suggest a terminator at the last fixture.

2. The dipswitch settings for Master/Slave mode is as follows. For Sound Active mode the Master unit must
have dipswitches 1-9 in the “Off” position and F1 dipswitch in the “On” position.

3. For the slave units, put dipswitch F1 “On” and F2 “Off” for a synchronous pattern. For a contrasting
pattern put the F2 dipswitch in the “On” position.

DMX TRAITS:

CHANNEL 1: MODES
0 - 15 = MIX AUTO
16 - 127 = MACRO
128 - 239 = SOUND ACTIVE SINGLE SHOW
240 - 255 = SOUND ACTIVE MIX SHOW 1-15

CHANNEL 2: SHOWS
0 - 17 = SHOW 1
18 - 34 = SHOW 2
35 - 51 = SHOW 3
52 - 68 = SHOW 4
69 - 85 = SHOW 5
86 - 102 = SHOW 6
103 - 119 = SHOW 7
120 - 136 = SHOW 8
137 - 153 = SHOW 9

CHANNEL 2: SHOWS CONT.
154 - 170 = SHOW 10
171 - 187 = SHOW 11
188 - 204 = SHOW 12
205 - 221 = SHOW 13
222 - 238 = SHOW 14
239 - 255 = SHOW 15

CHANNEL 3: MACROS & PROGRAM SPEED
0 - 7 = BLACKOUT
8 - 241 = 39 SCENES
242 - 247 = SPEED FLASH
248 - 255 = FULL ON

0 - 255 = PROGRAM SPEED SLOW - FAST

CHANNEL 4: MASTER DIMMER
0 - 255 = INTENSITY 0% - 100%

When Channel 1 is between the values of 0 - 15, channel 3 will control the speed of the auto pro­gram.

©Eliminator® Los Angeles, CA. - www.EliminatorLighting.com