Eliminator EM30 User guide

EM30

User Manual

©2023 Eliminator Lighting all rights reserved. Information, specications, diagrams, images, and in-

structions herein are subject to change without notice. Eliminator logo and identifying product names
and numbers herein are trademarks of Eliminator Lighting. Copyright protection claimed includes all
forms and matters of copyrightable materials and information now allowed by statutory or judicial law

or hereinafter granted. Product names used in this document may be trademarks or registered trade­marks of their respective companies and are hereby acknowledged. All non-Eliminator brands and

product names are trademarks or registered trademarks of their respective companies.

Eliminator Lighting and all afliated companies hereby disclaim any and all liabilities for property,

equipment, building, and electrical damages, injuries to any persons, and direct or indirect economic
loss associated with the use or reliance of any information contained within this document, and/or as a

result of the improper, unsafe, insufcient and negligent assembly, installation, rigging, and opera-tion

of this product.

Eliminator Lighting

6122 S. Eastern Ave. Los Angeles, CA. 90040

323-582-2650 | Fax [phone] | www.adj.com | [e-mail]

ADJ SUPPLY Europe B.V

Junostraat 2 6468 EW Kerkrade, The Netherlands
[phone] | Fax [phone]

www.americandj.eu | [e-mail]

ADJ PRODUCTS GROUP Mexico

AV Santa Ana 30 Parque Industrial Lerma, Lerma, Mexico 52000
[phone]

DOCUMENT VERSION

Due to additional product features and/or enhancements, an updated version of this
document may be available online.

Please check www.adj.com for the latest revision/update of this manual before
beginning installation and/or programming.

Date

07/28/23 1.0 N/A N/A Initial release

Document

Version

Software

Version >

DMX Channel Mode Notes

2

CONTENTS

General Information 4

Limited Warranty (USA Only) 5

Safety Guidelines 6

Maintenance Guidelines 7

Overview 8

Installation Guidelines 9

Frequently Asked Questions 13

Specications | Dimensional Drawings 14

3

GENERAL INFORMATION

INTRODUCTION

Please read and understand all instructions in this manual carefully and thoroughly before attempting

to operate this product. These instructions contain important safety and use information.

UNPACKING

This device has been thoroughly tested and has been shipped in perfect operating condition. Carefully

check the shipping carton for damage that may have occurred during shipping. If the carton appears
to be damaged, carefully inspect the unit for damage and be sure all accessories necessary to operate
the unit have arrived intact. In the event damage has been found or parts are missing, please contact
our customer support team for further instructions. Please do not return this kit to your dealer without

rst contacting customer support at the number listed below. Please do not discard the shipping carton

in the trash. Please recycle whenever possible.

CUSTOMER SUPPORT
Tel: [phone] | Fax: [phone]

www.adj.com | [e-mail]

WARRANTY RETURNS

All returned service items, whether under warranty or not, must be freight pre-paid and accompanied by a
return authorization (R.A.) number. The R.A. number must be clearly written on the outside of the return

package. A brief description of the problem as well as the R.A. number must also be written down on a piece
of paper and included in the shipping container. If the unit is under warranty, you must provide a copy of
your proof of purchase invoice. Items returned without an R.A. number clearly marked on the outside of the

package will be refused and returned at customer’s expense. You may obtain an R.A. number by contacting

customer support.

4

LIMITED WARRANTY (USA ONLY)

A. Eliminator Lighting, an ADJ Products, LLC brand, hereby warrants, to the original purchaser, Eliminator

Lighting products to be free of manufacturing defects in material and workmanship for a prescribed

period from the date of purchase (see specic warranty period on reverse). This warranty shall be

valid only if the product is purchased within the United States of America, including possessions and

territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable

evidence, at the time service is sought.

B. For warranty service, you must obtain a Return Authorization number (RA#) before sending back the

product-please contact ADJ Products, LLC Service Department at 800-322-6337. Send the product
only to the Eliminator Lighting factory. All shipping charges must be pre-paid. If the requested repairs

or service (including parts replacement) are within the terms of this warranty, Eliminator Lighting
will pay return shipping charges only to a designated point within the United States. If the entire

instrument is sent, it must be shipped in its original package. No accessories should be shipped

with the product. If any accessories are shipped with the product, Eliminator Lighting shall have no
liability whatsoever for loss of or damage to any such accessories, or for the safe return thereof.

C. This warranty is void of the serial number has been altered or removed; if the product is modied

in any manner which Eliminator Lighting concludes, after inspection, affects the reliability of the
product, if the product has been repaired or service by anyone other than ADJ Products, LLC factory

unless prior written authorization was issued to purchaser by Eliminator Lighting; if the product is

damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contact, and this warranty does not include maintenance, cleaning or periodic

check up. During the period specied above, Eliminator Lighting will replace defective parts at
its expense with new or refurbished parts, and will absorb all expenses for warrant service and
repair labor by reason of defects in material or workmanship. The sole responsibility of Eliminator

Lighting under this warranty shall be limited to the repair of the product, or replacement thereof,
including parts, at the sole discretion of Eliminator Lighting. All products covered by this warranty

were manufactured after August 15, 2012, and bear identifying marks to that effect.

E. Eliminator Lighting reserves the right to make changes in design and/or improvements upon its

products without any obligation to include these changes in any products theretofore manufactured.

F. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied

with products described above. Except to the extent prohibited by applicable law, all implied warranties

made by Eliminator Lighting in connection with this product, including warranties of merchantability

or tness, are limited in duration to the warranty period set forth above. And no warranties, whether
expressed or implied, including warranties of merchantability or tness, shall apply to this product
after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or
replacement as is expressly provided above; and under no circumstances shall Eliminator Lighting

be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use,
this product.

G. This warranty is the only written warranty applicable to Eliminator Lighting products and supersedes

all prior warranties and written descriptions of warranty terms and conditions heretofore published.

LIMITED WARRANTY PERIODS

• All Eliminator Lighting products (except laser diodes) = 1-year (365 days) Limited Warranty

(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble
Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding LED and lamps)

• Laser Products = 1 Year (365 Days) Limited Warranty (excludes laser diodes which have 6

month limited warranty)

• Batteries = 180 Day Limited Warranty (excluding batteries which have a 180 day limited warranty)

5

SAFETY GUIDELINES

To guarantee a smooth operation, it is important to follow all instructions and guidelines in this man-

ual. ELIMINATOR LIGHTING is not responsible for injury and/or damages resulting from the misuse

of these devices due to the disregard of the information printed in this manual. Only qualied and/
or certied personnel should perform installation of these devices and only the original rigging parts
included with these devices should be used for installation. Any modications to these devices and/or
the included mounting hardware will void the original manufacturer’s warranty and increase the risk of

damage and/or personal injury.

DAMAGES RESULTING FROM MODIFICATIONS TO THIS DEVICE AND/OR THE
DISREGARD OF SAFETY GUIDELINES IN THIS MANUAL VOID THE MANUFACTUR-

ER’S WARRANTY AND ARE NOT SUBJECT TO ANY WARRANTY CLAIMS AND/OR

REPAIRS.

KEEP FLAMMABLE MATERIALS AWAY FROM THIS DEVICE!

INDOOR / DRY LOCATIONS ONLY!
DO NOT EXPOSE TO RAIN AND / OR MOISTURE!

NEVER LOOK DIRECTLY INTO THE REFLECTED LIGHT SOURCE!
RETINA INJURY RISK - MAY INDUCE BLINDNESS!
SENSITIVE PERSONS MAY SUFFER AN EPILEPTIC SHOCK!

• DO NOT position device close to any FLAMMABLE MATERIALS while operating.

• DO NOT attempt installation and/or operation of devices if you lack the relevant knowledge.

• DO NOT permit operation by persons who are not qualied to operate these types of devices.

• DO NOT shake devices, and avoid brute force when installing and/or operating.

• DO NOT remove or disassemble devices, as there are NO user serviceable parts inside.

• ALWAYS disconnect devices from main power source (not included) before performing any clean-
ing.

• ALWAYS wear gloves when handling the mirror ball.

• ALWAYS be careful when handling the mirror ball, as damaged mirror panels can cause cuts and
other injuries.

• Only use recommended rigging hardware as described in this guide.

• Use only the original packaging and materials to transport these devices for service.

6

MAINTENANCE GUIDELINES

CLEANING

Frequent cleaning is recommended to ensure proper function, optimized light output, and an extend­ed life. The frequency of cleaning depends on the environment that the device operates in: damp,
smoky or particularly dirty environments can cause greater accumulation of dirt on the mirrored sur­face. Clean the external surface periodically with a soft, dry cloth to avoid dirt/debris accumulation.

NEVER use alcohol, solvents, or ammonia-based cleaners.

MAINTENANCE

Regular inspections are recommended to ensure proper function and extended life. There are no user

serviceable parts inside these devices. Please refer all other service issues to Eliminator Lighting.
Should you need any spare parts, please order genuine parts from Eliminator Lighting.

Please refer to the following points during routine inspections:

• Be sure all screws and fasteners are securely tightened at all times. Loose screws may fall out
during normal operation, resulting in damage or injury as larger parts could fall.

• Check for any deformations on the mirrored ball, rigging hardware, and rigging points (ceiling,
suspension, trussing. etc.) Damaged rigging points or unsecured rigging could cause the devices
to fall and seriously injure a person(s).

7

OVERVIEW

Mirror

Ball

Primary

Mounting

Loop

Secondary

Mounting

Loop

8

INSTALLATION GUIDELINES

FLAMMABLE MATERIAL WARNING

Keep devices at least 5.0 ft (1.5m) away from ammable materials and/or pyrotechnics.

DO NOT INSTALL THE DEVICE IF YOU LACK THE RELEVANT QUALIFICATIONS!

OVERHEAD RIGGING REQUIRES EXTENSIVE EXPERIENCE, INCLUDING BUT NOT LIMITED
TO CALCULATING WORKING LOAD LIMITS, KNOWLEDGE OF INSTALLATION MATERIAL BE­ING USED, AND PERIODIC SAFETY INSPECTION OF ALL INSTALLATION MATERIAL. IF YOU
LACK THESE QUALIFICATIONS, DO NOT ATTEMPT THE INSTALLATION YOURSELF. IMPROP­ER INSTALLATION CAN RESULT IN BODILY INJURY!

BEFORE RIGGING/MOUNTING DEVICES TO ANY METAL TRUSS/STRUCTURE OR CEILING,
A PROFESSIONAL EQUIPMENT INSTALLER MUST BE CONSULTED TO DETERMINE IF THE
METAL TRUSS/STRUCTURE OR CEILING IS PROPERLY CERTIFIED TO SAFELY HOLD THE
COMBINED WEIGHT OF THE FIXTURE, CLAMPS, CABLES, AND ACCESSORIES.

BEFORE MOUNTING DEVICES TO ANY SURFACE OR STRUCTURE, MAKE SURE THE SUR­FACE OR STRUCTURE CAN HOLD A MINIMUM POINT LOAD OF 10 TIMES THE WEIGHT OF
THE DEVICES.

FOR ADDED PROTECTION, MOUNT DEVICES IN AREAS AWAY FROM WALKING PATHS, SEAT­ING AREAS, OR AREAS WERE UNAUTHORIZED PERSONNEL CAN REACH THE DEVICES.

SECURE FIXTURE WITH A SECONDARY SAFETY ATTACHMENT, SUCH AS AN APPROPRIATE
SAFETY CABLE. (NOT INCLUDED)

NEVER STAND DIRECTLY BELOW THE DEVICES WHEN MOUNTING, REMOVING OR SERVIC­ING.

DEVICES MUST ALL BE INSTALLED FOLLOWING ALL LOCAL, NATIONAL, AND COUNTRY
COMMERICAL ELECTRICAL AND CONSTRUCTION CODES AND REGULATIONS.

9

INSTALLATION GUIDELINES

• The mirror ball unit includes two separate mounting eyelets. The eyelet located at the center of the
top of the mirror ball should be used as the primary mounting point, while the eyelet located slightly
off-center should be used as the secondary mounting point. Please refer to the Overview section of
this manual.

• In order to safeguard against personal injury and material damage, both the primary mounting eyelet
and the secondary mounting eyelet should be utilized.

• Mounting hardware (such as chains, safety cables, or carabiners) should be rated to support 12 times

the weight of the unit. This applies to hardware attached to both the primary and secondary mounting

eyelets.

• When installing the mirror ball in a rotating display, make sure to mount the mirror ball in such a way
that the mounting cables or chains do not become tangled as the mirror ball rotates.

• Installation should NEVER be done using hardware constructed of an abrasive material, as this could

lead to excessive wear on the mounting eyelets.

• Always ensure that the unit is rmly xed to avoid vibration and slipping during operation.

• Always ensure that the structure to which you are attaching the unit is secure and is able to support

at least 10 times the unit’s weight. Additionally, always use a safety cable that can hold 12 times the
weight of the unit when installing the xture.

• The equipment must be installed by a professional and it must be installed in a place where it is out of
the reach of the general public.

• It is strongly advised that installation should be performed by multiple individuals, as the bulky nature
of the unit may require two hands for support during installation.

• Always wear gloves when handling the mirror ball to avoid leaving ngerprints on the mirrors, and to
protect yourself against broken mirror pieces.

• NEVER install a mirror ball with damaged mirror pieces, as these could come loose and fall
during operation and cause serious injury!

10

INSTALLATION GUIDELINES

SAFETY CABLE ATTACHMENT

Use of a secondary safety cable is required. To install, attach a safety cable to the mirror ball eyelet and
the motor safety eyelet or mounting xture.

MAIN CABLE

ATTACHMENT POINTS

SAFETY CABLE

ATTACHMENT POINTS

If installing to a mirror ball motor, power the motor on and conrm that the mirror ball is able to rotate free-

ly and without obstruction.

11

INSTALLATION GUIDELINES

LIGHTING THE MIRROR BALL

Experiment with different angles and distances to achieve the desired result.

12

FREQUENTLY ASKED QUESTIONS

Can the EM30 be mounted to a ceiling?

Yes, it may be installed onto a at ceiling surface that can support 10 times the combined total weight

of the attached mirror ball, motor and any mounting accessories. Careful planning must be used when

calculating the combined weight and determining if the at ceiling surface can support the weight of

the motor and mirror ball. PLEASE CONSULT A PROFESSIONAL FOR CEILING INSTALLATION
GUIDANCE!

Is it necessary to use both of the mounting eyelets when installing this product?

Yes. It is crucial to install the mirror ball using both mounting eyelets in order to provide maximum

protection against personal injury and material damage.

Is a light included with the EM30?

No. However, a variety of lighting xtures, options, and kits are available for purchase at www.adj.com.

What method should be used to clean the mirror ball?

Clean the external of the mirror ball surface periodically with a soft cloth to avoid dirt/debris accumulation.
NEVER use alcohol, solvents, or ammonia-based cleaners.

Is the mirror ball available in other sizes?

Yes, Eliminator offers mirror balls in a variety of sizes. Please visit our website for more details.

ORDERING INFORMATION

SKU (US) SKU (EU) DESCRIPTION

EM30 1900000205 EM30 Mirror Ball
MHD400 1900000215 HD-MB40 Mirror Ball Motor

13

SPECIFICATIONS

Model: EM30
Mirror Ball Body Diameter: 29.7 in (755mm)
Weight: 32.18 lbs / 14.6 kg

DIMENSIONAL DRAWINGS

29.7in (755mm)

14

This page intentionally left blank.

15