eligent EEPE-DF-FT23-8HCY-UK, EEPE-DF-FT23-8HCY User Manual

We reserve the right for any errors in text or images and any
necessary changes made to technical data. If you have any questions
regarding technical problems please contact us at the following
address.

Vi reserverar oss för ev. text- och bildfel samt ändringar av tekniska
data. Vid tekniska problem eller andra frågor kan du kontakt oss.

Vi tar forbehold om tekst- og fotofeil samt endringer av tekniske
data. Ved tekniske- eller øvrige spørsmål, vennligst kontakt oss.

Teknisten ongelmien ilmetessä, ota meihin yhteyttä.

Emme vastaa mahdollisista kuva- tai tekstivirheistä, emmekä
myöskään teknisten tietojen muutoksista.

SVERIGE KUNDTJÄNST
Tel: [phone]
Fax: [phone]
E-post:
[e-mail]
www.clasohlson.se

NORGE KUNDESENTER
Tel: [phone]
Fax: [phone]
E-Post:
[e-mail]
www.clasohlson.no

ASIAKASPALVELU SUOMI
Puh: 020 111 2222
Faksi: 020 111 2221
Sähköposti: [e-mail]
www.clasohlson.fi

For consumer contact, please
visit www.clasohlson.co.uk and
click on customer service.

Art. No. / Art. Nr. / Artikkelnummer / Tuotenumero:

18-2286 / 36-5000

EEPE-DF-FT23-8HCY-UK

EEPE-DF-FT23-8HCY

TABLE FAN

Model: EEPE-DF-FT23-8HCY-UK / EEPE-DF-FT23-8HCY

ENGLISH

ENGLISH

Read through the entire instruction manual before use and save for future reference. We reserve
the right for any eventual errors in the text or figures and for changes in technical data. For technical
problems or other questions, please contact our customer service (see contact information on
reverse side).

Safety instructions:

· Read all of the instructions carefully before use. Neglecting to follow these safety instructions
may lead to fire, short circuit or life-threatening injury. For this reason, save these instructions
for future reference.

· Make sure that all parts are accounted for and undamaged when unpacking. Never use the
product if the power cord, plug or other part of the product is damaged or functioning incorrectly.
Do not try to personally repair or modify this product. Instead, contact a qualified repairman.

· The table fan may only be used indoors in a dry and clean environment. Never place the fan
close to a bathtub, pool or other water basin where it can fall in.

· Always unplug the fan when not being used.

· Never leave children in the same room as the fan without adult supervision.

· Never expose the fan to water or other liquids.

· Do not plug in the fan before it has been assembled.

· Keep foreign objects from entering the fan since this may lead to short circuit, electrical shock or fire.

· Never turn off the fan by unplugging it. Make sure that the power switch is turned off (set to
[OFF]) and then unplug it.

· Should the power cord become damaged it must immediately be replaced by the manufacturer,
service agent or other qualified person. Replacement may under no circumstances be carried
out by a non-professional.

Assembly:
Warning! The table fans power cord must be unplugged before assembly.

1. Unpack contents of packaging. Remove protective plastic.

2. Assemble the fan onto the base plate (8) and fasten it with included screw at the bottom.

3. Fit the rear guard (4) on the motor hosing and lock it in place with the lock nut (3).

4. Press the fan blade (2) onto the motor shaft (5). Make sure that the metal ring (locking ring)
on the fan blades interior surrounds the plastic and locks the fan blade onto the motor shaft.

5. Hang the front guard (1) on the rear guard. Fasten these guards together securely by using
the two fasteners around the guards.

6. Plug the fan into a suitable wall outlet.

Operation

· The table fan can be set to oscillate sideways or stand stationary. The table fan housing can
be tiled vertically.

· Press down on the knob (6) to start the horizontal oscillation thus spreading the air stream
over a wide area. Pull up the knob (6) to stop the oscillation and therefore focus the air stream.

· The table fan has two speeds. Set desired speed [H] or [L] with buttons (7).

· Press [OFF] to turn off the fan.

Page 1

Cleaning

· Use only a moist cloth when cleaning, never strong cleaning agents or other solvents.

· Use a vacuum cleaner when desired to suck dust from the guard.

Warning!

Should the power cord become damaged it must immediately be replaced by the manufacturer,
service agent or other qualified person. Replacement may under no circumstances be carried out
by a non-professional.

Technical data:

Voltage: 220 - 240 V AC, 50 Hz
Power: 28W
Protection class: IP20

1 234 5 6

1. Front guard

2. Fan blade

3. Lock nut

4. Rear guard

5. Motor shaft

6. Oscillation lever knob

7. Buttons

8. Base plate

Page 2

7

8