Elgato Ring Light User manual

Federal Communication Commission Interference Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-Reorient or relocate the receiving antenna.

-Increase the separation between the equipment and receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-Consult the dealer or an experienced radio/TV technician for help.

FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate this equipment. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and a human body.

For questions about Elgato product compliance with FCC regulations, please contact: Compliance Officer, Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA

This device complies with Industry Canada license-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

Le present appareil est conforme aux CNR d‘Industrie Canada applicables aux appareils radio exempts de licence. L‘exploitation est autorisee aux deux conditions suivantes : (1) l‘appareil ne doit pas produire de brouillage, et (2) l‘utilisateur de l‘appareil doit accepter tout brouillage radioelectrique subi, meme si le brouillage est susceptible d‘en compromettre le fonctionnement.

Elgato, a division of:

Corsair Memory Inc., 47100 Bayside Pkwy, Fremont, CA 94538, USA

Corsair Memory, BV Wormerweg 8, 1311 XB, Almere, Netherlands

Part: 51LAC9903

R-R-CSI-20LAC9901

R-R-SXt-A6541304000I

Applicant Name ( ): Corsair Memory, Inc. Product Name ( ): Ring Light

Model No.( ): 20LAC9901

Manufactured Year & Month ( ): Please refer to gift box sticker

Manufacturer & Country of Origin ( ): Corsair Memory, Inc./ Made in Taiwan A/S : ( ) , 1522-1460

/elgato

Quick Start Guide

Guide de prise en main rapide Kurzanleitung

Guía de inicio rápido Guida rapida Snelstartgids Pikaopas

Lynstart guide Hurtigveiledning Kom igång

Guia de Início Rápido

Hızlı Kurulum Rehberi

Σύντομος οδηγός

Skrócona instrukcja

Краткое руководство

عيرسلا ءدبلا ليلد

Set up your Ring Light

Secure Ring Light to the 1/4 inch screw on top of the ball head. Extend Master Mount S to your preferred height.

Tighten	Loosen
Do not overtighten.
Push the button to	Padded and
release and reposition	expandable up
the ratchet lever.	to 6 cm / 2.35 in
Loosen	Tighten
Adjustment Modes
Ring Light is in Brightness mode by default. Press
+ and - simultaneously to enter Color Temperature
mode (Ring Light will flash twice) and repeat to enter
Brightness mode (Ring Light will flash once).
Brightness Adjustment
single press (increase brightness by 10%)
single press (decrease brightness by 10%)
long press (increase brightness to 100%)
long press (decrease brightness to 3%)	Brightness Mode
Color Temperature Adjustment
single press (increase color warmth by 200K)
single press (decrease color warmth by 200K)
long press (increase color warmth to 2900K)
long press (decrease color warmth to 7000K)	Color Temperature Mode

Maximum load 2,00 kg / 4,50 lbs

Minimum 44 cm / 17 in Maximum 74 cm / 29 in

It is normal for Master Mount S to shake when fully extended.

Connect the power supply and plug it into a power outlet.

I = ON

0 = OFF

II = RESET

Installation (Software)

10s

Download and install the Control Center app	Switch on Ring Light. It will take
for Mac, Windows, iOS or Android.	approximately 10 seconds to boot up.
3	4

Launch the Control Center app and pair Ring	Use Control Center to switch Ring Light on/
Light by clicking the + icon.	off, adjust brightness, and fine-tune color
	temperature.

If your PC is not equipped with Wi-Fi, use the Elgato Control Center app on your iOS or Android device to add Ring Light. A Wi-Fi connection is only needed for initial pairing. Once paired, you can control Ring Light via any wired or wireless device in your network.

Reset

10s

RESET will restore Ring Light factory settings and forget all Wi-Fi credentials.

Power off Ring Light. Push and hold the RESET Button (II) for at least 10 seconds until the light flashes 3x. Wait a moment before switching on Ring Light again.

Warning

•Ring Light may become hot during prolonged use. Always handle with care.

•Do not cover Ring Light, especially its ventilation holes.

•Do not place on or near a carpet, curtains, or any other flammable materials.

•Be especially cautious when setting up near children.

•Do not attach items to Ring Light.

•Do not leave Ring Light exposed to direct sunlight.

•Do not set up in areas susceptible to strong air currents. Drafts and breezes can cause movement that may result in damage to the product.

•Keep Ring Light free from dirt and dust. If it becomes dirty, wipe it lightly with a soft cloth moistened with a little water and mild, neutral detergent. Benzene, thinner, and other volatile agents can cause permanent damage and should never be used for cleaning.

•Always secure Ring Light and Master Mount S to a level, stable surface. Uneven or unstable surfaces may cause tipping and result in damage or personal injury.

•Do not use Ring Light or Master Mount S for applications other than those specified in this guide or the packaging.

	FCC	IC	CE
2.4 GHz	2412 - 2462 MHz	2412 - 2462 MHz	2412 - 2472 MHz
5 GHz (Band 1 & 2)	5180 - 5320 MHz	5180 - 5320 MHz	5180 - 5320 MHz
5 GHz (Band 3)	5500 - 5700 MHz	5500 - 5800 MHz	5500 - 5700 MHz
		5660 - 5700 MHz
5 GHz (Band 4)	5745 - 5825 MHz	5745 - 5825 MHz	X

CE Wi-Fi 2.4 GHz Max RF e.i.r.p power < 20dBm, Wi-Fi 5 GHz Max RF e.i.r.p. power < 23dBm, Temperature range: 0 °C - 45 °C

This equipment complies with FCC RF, IC RSS-102 and CE radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. For indoor use only.

Hereby, Corsair Memory Inc. declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EC. The declaration of conformity for Elgato products is available at www.elgato.com/doc

+ 7 hidden pages