elero Antriebstechnik 28010X9X3 Users Manual

UART-RF-Stick 915

Connection and installation

address

IC: 8929A- 280101X9X3

28 010 0903 - Integration Manual

FCC / IC
FCC ID: YBU28010X9X3

USA (FCC)

Part 15 Statement gem. FCC 15.19/RSS Gen Issue 3
Sect. 7.1.3
This device (elero UART-RF-Stick 915) complies with
Part 15 of the FCC Rules and with Industry Canada
license-exempt RSS standard(s). Operation is subject
to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,

including interference that may cause undesired
operation.

General

Product description

The elero UART RF Stick 915

• is a radio receiver for the elero ProLine 2 radio system.

• serves as a receiver module for devices for home
automation such as drives for roller shutters,
Venetian blinds, curtains or lighting systems and
heater systems.

• is constructed as a PCB device with integrated radio
module and antenna.

• does not have its own housing.

• communicates with the target product via a UART
interface and via the integrated radio module with the
elero ProLine 2 radio system.

• offers the full functionality of an elero ProLine 2 radio
receiver such as automatic functions. The routing
function is also integrated.

Intended use

The elero UART RF Stick 915 can be used in the
intended home automation devices such as drives for
roller shutters, Venetian blinds or lighting systems and
heater systems.
The devices also have a suitable slot for the UART RF
Stick 915.

Exclusion of liability
elero GmbH accepts no liability for injury, damage

or financial losses arising from modifications to the
device, improper use or a failure to observe the operat­ing instructions. Liability for material defects is exclud­ed in such cases.

Technical data

Canada, Industry Canada (IC)

Le présent appareil (elero UART-RF-Stick 915) est
conforme aux CNR d‘Industrie Canada applicables aux
appareils radio exempts de licence. L‘exploitation est
autorisée aux deux conditions suivantes :
(1) l‘appareil ne doit pas produire de brouillage, et
(2) l‘utilisateur de l‘appareil doit accepter tout brouillage

radioélectrique subi, même si le brouillage est sus­ceptible d‘en compromettre le fonctionnement.

Caution:

Changes or modications not expressly approved by

the party responsible for compliance could void the
user’s authority to operate the equipment.

Information:

This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer­ence in a residential installation. This equipment gen­erates, uses and can radiate radio frequency energy
and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment o󰀨 and on, the user is encour­aged to try to correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and
receiver.

• Connect the equipment into an outlet on a circuit dif­ferent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/ TV techni­cian for help

Product designation UART RF Stick 915

Operating voltage [V] DC 2.7 ... 3.0 ... 3.6

Transmission frequency
[MHz]

Transmitting power [dBm] 1 (decibel milliwatt)

Operating temperature range
[°C]

Dimensions [mm] 42.5 x 19.5

Item No. 28 010.0903

Contains FCC ID YBU28010X9X3

Contains IC 8929A-28010X9X3

915 (band)

0 ... 50

See operating manual of the target product.

Manufacturer’s

elero GmbH

72660 Beuren
GERMANY
www.elero.com

Service

If faults should occur despite
proper operation or if the device
is damaged, contact your dealer
or the manufacturer.

138204501_EN_0716

Label requirements for the target device

The target product must be labeled with the following
three specifications:

• Contains FCC ID: YBU28010X9X3

• Contains IC: 8929A-28010X9X3

• This device complies with Part 15 of the FCC Rules
and with Industry Canada license-exempt RSS stan­dard(s). Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference,
and
(2) this device must accept any interference
received, including interference that may cause
undesired operation.