Elenco Electronics XK-700K Assembly And Instruction Manual
DIGITAL / ANALOG TRAINER
MODEL XK-700K
A COMPLETE MINI-LAB FOR BUILDING,TESTING
AND PROTOTYPING ANALOG AND DIGITAL CIRCUITS
Elenco Electronics, Inc.
Copyright © 1996 Elenco Electronics, Inc. Revised 2001 REV-E 753029
Tools and meter shown not included.
Assembly & Instruction Manual
-1-
PS-700-B
XK-700K POWER SUPPLY KIT (PS-700-B) PARTS LIST
RESISTORS
Qty. Symbol Value Description Part #
2 R1, R2 120Ω 5% 1/4W (brown-red-brown-gold) 131200
1 VR3 1kΩ Pot PC MNT 192412
2 VR1, VR2 2kΩ Pot PC MNT 192421
1 VR4 100kΩ Pot PC MNT 192612
CAPACITORS
Qty. Symbol Value Description Part #
5 C6 - C10 .1µF 100V Mylar 251017
7 C11 - C17 100µF Electrolytic 281045
4 C1, C2, C4, C5 1000µF 35V Electrolytic 291096
1 C3 2200µF 25V Electrolytic 292225
SEMICONDUCTORS
Qty. Symbol Description Part #
15 D1 - D15 1N4001 Diode 314001
1 U1 LM317 Integrated Circuit 330317
1 U5 LM337 Integrated Circuit 330337
1 U3 LM7805 Integrated Circuit 337805
1 U2 LM7812 Integrated Circuit 337812
1 U4 LM7912 Integrated Circuit 337912
MISCELLANEOUS
Qty. Description Part #
1 Transformer 44K500
1 PC Board 514550
1 Fuse 1.25A 530125
1 Switch Illuminated 541204
2 Connector 3-pin 591032
1 Connector 5-pin 591052
4 Bracket L 4-40 tap 613008
1 Panel Top 614108
1 Panel Side Left 614506
1 Panel Side Right 614507
1 Panel Back 614508
4 Knob 622009
1 Case 623051
1 Strain Relief 624003
1 Spacer Nylon 7/16” x 3/16”Tap 624013
1 Connector Receptacle 626020
1 Connector Plug 626021
1
Screw 4-40 x 1/4” Phillips, Flat Head
641431
9 Screw 4-40 x 1/4” Phillips Truss 641438
6 Screw 6-32 x 5/16” Slotted 641641
2 Screw 8-32 x 3/8” Phillips 641840
2 Screw #4 x 1/4” Phillips AB 642430
4 Screw 4-40 x 1/4” Phillips Thrd Ct 642432
4 Screw #6 x 1/2 Phillips AB 642662
Qty. Description Part #
4 Screw #6 x 3/8” Phillips Thrd Ct 643652
4 Nut 7mm 644101
6 Nut 6-32 644601
2 Nut 8-32 644800
4 Washer 8mm x 14mm (Pot) 645101
4 Washer #6 Black 645400
4 Washer Fiber 645404
2 Lockwasher #8 EXT 646828
1 Fuse Holder 663000
4 Bredblox 4-pin 665204
2 Ter minal Male Crimp 666010
2 Ter minal Female Crimp 666011
1 Manual 753029
5 Insulator Mica 780002
5 Insulator Washer 780101
1 Silicon Grease 790004
6” Wire #20 Red Stranded 813210
2.5’ Wire #22 Bare Wire 845000
1 Line Cord 862105
2” Shrink Tubing 3/16” 890120
1” Shrink Tubing 1/4” 890701
2” Shrink Tubing 1/2” 891101
2” Shrink Tubing 3/4” 899110
1 Solder Tube 9ST4A
Screw Identification
Phillips AB Screw 4-40 / #6 Thread Cutting Screw Standard Screw
(Type 23)
Flat Head Screw
Truss Head Screw
-2-
PARTS VERIFICA TION
Before beginning the assembly process, first familiarize yourself with the components and this instruction book.
Ver ify that all par ts are present. This is done best by checking off each item in the parts list.
IDENTIFYING RESISTOR VALUES
Use the following information as a guide in properly identifying the value of resistors.
BAND 1
1st Digit
Color Digit
Black 0
Brown 1
Red 2
Orange 3
Yellow 4
Green 5
Blue 6
Violet 7
Gray 8
White 9
BAND 2
2nd Digit
Color Digit
Black 0
Brown 1
Red 2
Orange 3
Yellow 4
Green 5
Blue 6
Violet 7
Gray 8
White 9
Multiplier
Color Multiplier
Black 1
Brown 10
Red 100
Orange 1,000
Yellow 10,000
Green 100,000
Blue 1,000,000
Silver 0.01
Gold 0.1
Resistance
Tolerance
Color Tolerance
Silver +10%
Gold +
5%
Brown +
1%
Red +
2%
Orange +
3%
Green +
0.5%
Blue +0.25%
Violet +0.1%
Bands
1 2
Multiplier
Tolerance
Resistors
Capacitors
Electrolytic
(Lytic)
(Radial)
Connectors
Switches
Mylar
PC Mount
Potentiometer
Rotary DPDT
Spacer
Discap
Knob
PC Mount
Trim Pot
3-Pin
4-Pin 5-Pin
Miscellaneous
Illuminated TransformerBredblox
Connector Plug
Connector
Receptacle
Fuse
Assembly
Male Crimp
Terminal
Female Crimp
Terminal
Integrated
Circuit (IC)
IC Socket
Transistor
Integrated
Circuit (IC)
Diode
LED
IDENTIFYING CAPACITOR VALUES
Capacitors will be identified by their capacitance value in pF (picofarads), nF (nanofarads), or µF (microfarads). Most
capacitors will have their actual value printed on them. Some capacitors may have their value printed in the following
manner. The maximum operating voltage may also be printed on the capacitor.
Second Digit
First Digit
Multiplier
Tolerance*
For the No. 01234589
Multiply By 1 10 100 1k 10k 100k .01 0.1
Multiplier
Note: The letter “R”may be used at times to
signify a decimal point; as in 3R3 = 3.3
10µF 16V
103K
100V
The letter M indicates a tolerance of +20%
The letter K indicates a tolerance of +
10%
The letter J indicates a tolerance of +5%
Maximum Working Voltage
The value is 10 x 1,000 =
10,000pF or .01µF 100V
*
Semiconductors
-3-
Introduction
The most important factor in assembling your XK-700K Digital / Analog Trainer Kit is good soldering techniques.
Using the proper soldering iron is of prime impor tance. A small pencil type soldering iron of 25 - 40 watts is
recommended.The tip of the iron must be kept clean at all times and well tinned.
Safety Procedures
• Wear eye protection when soldering.
•
Locate soldering iron in an area where you do not have to go around it or reach over it.
• Do not hold solder in your mouth. Solder contains lead and is a toxic substance. Wash your hands
thoroughly after handling solder.
• Be sure that there is adequate ventilation present.
Assemble Components
In all of the following assembly steps, the components must be installed on the top side of the PC board unless
otherwise indicated. The top legend shows where each component goes. The leads pass through the
corresponding holes in the board and are soldered on the foil side.
Use only rosin core solder of 63/37 alloy.
DO NOT USE ACID CORE SOLDER!
CONSTRUCTION
Solder
Soldering Iron
Foil
Solder
Soldering Iron
Foil
Component Lead
Soldering Iron
Circuit Board
Foil
Rosin
Soldering iron positioned
incorrectly.
Solder
Gap
Component Lead
Solder
Soldering Iron
Drag
Foil
1. Solder all components from
the copper foil side only.
Push the soldering iron tip
against both the lead and
the circuit board foil.
2. Apply a small amount of
solder to the iron tip. This
allows the heat to leave the
iron and onto the foil.
Immediately apply solder to
the opposite side of the
connection, away from the
iron. Allow the heated
component and the circuit
foil to melt the solder.
1. Insufficient heat - the
solder will not flow onto the
lead as shown.
3. Allow the solder to flow
around the connection.
Then, remove the solder
and the iron and let the
connection cool. The
solder should have flowed
smoothly and not lump
around the wire lead.
4.
Here is what a good solder
connection looks like.
2. Insufficient solder - let the
solder flow over the
connection until it is
covered. Use just enough
solder to cover the
connection.
3. Excessive solder - could
make connections that you
did not intend to between
adjacent foil areas or
terminals.
4. Solder bridges - occur
when solder runs between
circuit paths and creates a
short circuit. This is usually
caused by using too much
solder. To correct this,
simply drag your soldering
iron across the solder
bridge as shown.
What Good Soldering Looks Like
A good solder connection should be bright, shiny,
smooth, and uniformly flowed over all surfaces.
Types of Poor Soldering Connections
-4-
INTRODUCTION
The XK-700K Digital/Analog Trainer is divided into four separate kits: BB-700-A, PS-700-B, AN-700-C and DG700D. Each bag of parts is clearly identified. Open only the kit called for in your procedure. DO NOT open any
other bag at this time. The first kit is the BB-700-A which contains only the bredboard. The bredboard will be
assembled to the front panel of the trainer during the assembly of the PS-700-B Power Supply. Read your
instructions carefully.
Power Supply
The XK-700K has five built-in power supplies which will satify most design needs. This includes two variable
power supplies giving up to +20 volts and -20 volts at .5 amp. Below 15V, the current available is 1 amp. Three
fixed power supplies give you +12VDC, –12VDC or +5VDC at 1 amp each. These fixed voltages are the most
commonly used voltages for design work. All supplies are regulated to within 150mV. This means that you can
increase the current draw from no load to 0.5 amp and the voltage will change less than 150mV. All supplies
are also short circuit protected by using integrated circuit regulator devices.
Analog Trainer Section Function Generator
The analog trainer contains a complete function generator capable of producing sine, square and triangle
waveforms. The frequency of the generator is continuously variable from one hertz to over 100,000 hertz in five
steps. A fine tuning control makes the selection of any frequency easy. The output v oltage amplitude is v ariable
between 0 to 15Vpp. The output impedance is approximately 330 ohms.
Digital T rainer Section
The digital trainer has the necessary functions to do your digital experiments. The y consist of a cloc k gener ator,
two no-bounce switches, eight LED indicator lamps and eight data switches.
POWER SUPPLY SPECIFICATIONS
Power Supplies:
• +1.25V to 20VDC @ 0.5 amp (1.25V to 15V @ 1 amp).
• –1.25 to -20VDC @ 0.5 amp (–1.25V to –15V @ 1 amp).
• +12V +
5% @ 1 amp.
• –12V +5% @ 1 amp.
• +5V +5% @ 1 amp.
• 30VAC center tapped @ 1 amp.
• Load regulation - all DC supplies less than 0.2V no load to 0.5A.
• Line regulation - all DC supplies less than0.2V 105 to 135V.
• Hum and ripple - all DC supplies less than 0.01V RMS.
• Short protection - all DC supplies-inter nal IC ther mal cutoff.
• Fuse 1.25A 250V.
Variable Resistance (undedicated):
• 1kΩ Potentiometer
• 100kΩ Potentiometer
USERS DESCRIPTION OF FRONT PANEL CONTROLS
1) On/Off Switch - Allows power to be applied to all outputs. Switch will
light when on.
2) Fuse Holder - Easy access for replacement of 1.25A fuse.
3) Power Output Terminals - This provides 30VAC center tapped at
15 VAC; also provides output terminal for positive and negative
variable voltages.
4) Variable Positive Voltage Control - Var ies positive voltage from 1.25
to 20V at indicated output connector pin.
5) Variable Negative Voltage Control - Varies negative voltage from
–1.25V to –20V at indicated output connector pin.
6) Power Output Bredblox - Output terminals for GND, –12, +12, and +5.
7) Output terminals for 1k and 100k undedicated potentiometers.
8) 1kΩ undedicated potentiometer.
9) 100kΩ undedicated potentiometer.
1
2
3
4
5
7
8 9
6
Figure C
Mount down flush with PC board. The
value may be marked on the on the
back side of pot.
Cut off excess lead length after
soldering.
Figure B
Note: One side of the
bracket is longer. Mount
this side to the PC board.
Mount the bracket to the
top legend side of the PC
board with a 4-40 x 1/4”
screw and fiber washer.
Figure A
Mount the connector as shown and solder the
pins of the connector.
-5-
INSTALL COMPONENTS TO PC BOARD
Start Here
S1 - 5-Pin Connector
(see Figure A)
L-Bracket
(see Figure B)
VR4 - 100kΩ Pot
VR3 - 1kΩ Pot
(see Figure C)
S3 - 3-Pin Connector
S2 - 3-Pin Connector
(see Figure A)
L-Bracket
(see Figure B)
C8 - 0.1µF Mylar (104)
(see Figure D)
Bottom Left Corner of PC Board
Top Left Corner of PC Board
Figure D
Bend the capacitor at a 45
O
angle before soldering.Cut off
excess leads.
Cut off tab
PC Board
4-40 x 1/4”
Screw
Top Legend
Side of
PC Board
Fiber
Washer
Figure G
Diodes have polarity. Mount them
with the band as shown on the top
legend.
-6-
INSTALL COMPONENTS TO PC BOARD
C11 - 100µF 25V
(see Figure E)
R1 - 120Ω 5% 1/4W Resistor
(brown-red-brown-gold)
C6 - .1µF Mylar (104)
(see Figure D)
J28 - Jumper Wire
(see Figure F)
J6 - Jumper Wire
(see Figure F)
D12 - 1N4001 Diode
D11 - 1N4001 Diode
(see Figure G)
C14 - 100µF 25V Lytic
C17 - 100µF 25V Lytic
(see Figure E)
C10 - .1µF Mylar (104)
(see Figure D)
R2 - 120Ω 5% 1/4W Resistor
(brown-red-brown-gold)
J2 - Jumper Wire
(see Figure F)
J3 - Jumper Wire
(see Figure F)
Figure F
Cut a piece of the #22 bare wire
long enough so that 1/4” of wire
passes through each hole in the
PC board after the wire is formed.
Band
Bottom Left Corner of PC Board
Figure E
These capacitors are polarized. Be
sure to mount them with the “+”
lead in the correct hole as marked
on the PC board. Mount the
capacitor lying flat on the PC board
as shown below.
(+)
(–)
Start Here
INSTALL COMPONENTS TO PC BOARD
VR1 - 2kΩ Pot
VR2 - 2kΩ Pot
(see Figure C)
B1 - 4-Pin Bredblox
B2 - 4-Pin Bredblox
B3 - 4-Pin Bredblox
B4 - 4-Pin Bredblox
(see Figure H)
C12 - 100µF 25V Lytic
(see Figure E)
J26 - Jumper Wire
J7 - Jumper Wire
(see Figure F)
D15 - 1N4001 Diode
D14 - 1N4001 Diode
D13 - 1N4001 Diode
(see Figure G)
C15 - 100µF 25V Lytic
C16 - 100µF 25V Lytic
(see Figure E)
J4 - Jumper Wire
J1 - Jumper Wire
(see Figure F)
C13 - 100µF 25V Lytic
(see Figure E)
Bottom Left Corner of PC Board
-7-
Figure H
Hold the bredblock down flush
to the PC board from the top
legend side and solder the
metal pins in place. Then, melt
the plastic pins with your
soldering iron to hold the
plastic blocks in place, as
shown.
Start Here
Plastic Pins
Melt Pins
Figure I
Diodes have polarity. Mount them with
the band as shown on the top legend.
Figure J
These lytics must be mounted
horizontal to the PC board. Bend
the leads at right angles and then
insert the leads into the PC board
with the negative (–) lead and the
positive (+) lead in the correct holes
as marked on the PC board.
-8-
INSTALL COMPONENTS TO PC BOARD
C2 - 1000µF 35V Lytic
C4 - 1000µF 35V Lytic
(see Figure J)
Continue
L-Bracket
(see Figure B)
C7 - .1µF Mylar (104)
(see Figure D)
J5 - Jumper Wire *
(see Figure F)
C9 - .1µF (104) Mylar
(see Figure D)
L-Bracket
(see Figure B)
C1 - 1,000µF 35V Lytic
C5 - 1,000µF 35V Lytic
(see Figure J)
D1 - 1N4001 Diode
D2 - 1N4001 Diode
D3 - 1N4001 Diode
D4 - 1N4001 Diode
D5 - 1N4001 Diode
D6 - 1N4001 Diode
D7 - 1N4001 Diode
D8 - 1N4001 Diode
D9 - 1N4001 Diode
D10 - 1N4001 Diode
(see Figure I)
Bottom Right Corner of PC Board
C3 - 2200µF Lytic
Mount on foil side of PC board
Note the polarity
(see Figure J)
Top Right Corner
of PC Board
* Leftover wire will be used in
future sections.
Band
+
Start Here Continue
Start Here
-9-
MOUNTING THE PC BOARD
Note: The holes in the two side panels have been punched differently. Be sure that you have the correct side
panel when mounting them to the PC board.
IMPORTANT: Push the PC board up as far as possible before tightening the screws,as shown in Figure La.
Mount the back panel using four 4-40 x 1/4” thread cutting screws (see Figure K).
Mount the PC board to the side panels with four 4-40 x 1/4” screws (see Figure L).
Do not tighten the screws.
Figure L
4-40 x 1/4”
Screws
4-40 x 1/4”
Screws
Top Legend Side
of PC Board
Note: From the foil side of the PC board,
inspect the edges to be sure that there
are no component leads shorting against
the side panels.
Right Side
Left Side
Adjust the PC board
height with a 4-40 x
1/4” screw
4-40 x 1/4” Thread
Cutting Screws
4-40 x 1/4” Thread
Cutting Screws
Back Panel
Figure K
Right Side
Left Side
MOUNT COMPONENTS TO THE SIDE PANELS
Mount U1, U3 and U5 to the left side panel as shown in Figure N. Insert the pins of each IC into the holes of
the PC board. Then, with the hardware shown in Figure M, attach each IC to the side panel. Solder the pins
of the ICs to the PC board.
U3 - LM7805
U1 - LM317
U5 - LM337
-10-
Place the top panel onto the unit and align the components with the holes in the top panel. Push the PC board up until
the components come through the top panel and tighten the screws.
Figure La
6-23 Nut
IC
* Silicone Grease
Side Panel
Insulator Washer
6-32 x 5/16” Screw
* Take a small amount of silicone grease from the
packet and apply it with a toothpick onto the back of
the ICs.
Figure M
Mica
Figure N
U3
7805
U1
LM317
U5
LM337
Left Side
-11-
WIRE THE TRANSFORMER TO THE PC BOARD
Solder the wires to the PC board starting with the top yellow wire as shown in Figure P.
Yellow wire to point F on the PC board
Blue wire to point A on the PC board
Red wire to point C on the PC board
White wire to point E on the PC board
Red wire to point D on the PC board
Blue wire to point B on the PC board
Yellow wire to point G on the PC board
Mount U2 and U4 to the right side panel as shown in Figure O.
Insert the pins of each IC into the holes in the PC board. Then,
with the hardware shown in Figure MA, attach each IC to the
side panel. Solder the pins of the ICs to the PC board.
U4 - LM7912
U2 - LM7812
Mount the transformer with the black wires as sho wn in Figure O.
Use the two 8-32 x 3/8” screws, #8 lockwashers, and 8-32 nuts.
Transformer mounted
Right Side
Figure O
Note: Make sure that
the transformer does
not touch U4.
#8 Lockwashers
#8-32 x 3/8” Screws
8-32 Nuts
Transformer
Black Wires
U4
7912
U2
7812
Yellow (F)
Blue (A)
Red (C)
White (E)
Red (D)
Blue (B)
Yellow (G)
Figure P
Yellow (G)
Blue (B)
Blue (A)
Red (D)
White (E)
Yellow (F)
Red (C)
6-23 Nut
IC
* Silicone Grease
Side Panel
Insulator Washer
6-32 x 5/16” Screw
* Take a small amount of silicone grease from the packet and
apply it with a toothpick onto the back of the ICs.
Mica
Figure MA
HOW TO INSTALL CONNECTORS ONTO TRANSFORMER WIRES
A connector will be placed onto the primary wires of the transformer. This will allo w y ou to remove the top panel
from the trainer. Follow the procedures below.
Cut a six inch length off of each black primary wire.
Strip the insulation off of each end of the six inch wires to expose 1/4” of bare wire.
Place one wire onto the female pin and crimp the outer crimp tabs with pliers over the insulation as shown
in Figure 1A.
Crimp the inner tabs with pliers onto the bare wire as shown in Figure 1B.
Solder the wire to the pin as shown in Figure 1C.
Connect the other female pin to the other wire using the same procedures above.
Insert the two pin/wire assemblies into the female housing as shown in Figure 2. Pull on the wire to check
that the pin is inserted all the way in. It should not pull out of the housing. The locking tabs should be bent
outward to hold the pin in the housing.
Figure 1 Figure 2
T ransformer Wires
Strip the insulation off of each of the black primary wires to expose 1/4” of bare wire.
Place the wire onto the male pin and crimp the outer crimp tabs with pliers over the insulation as shown in
Figure 3A.
Crimp the inner tabs with pliers onto the bare wire as shown in Figure 3B.
Solder the wire to the pin as shown in Figure 3C.
Connect the other male pin to the other primary wire using the same procedures above.
Insert the two pin/wire assemblies into the male housing as shown in Figure 4. Pull on the wire to check that
the pin is inserted all the way in. It should not pull out of the housing.
Connect the male and female housing as shown in Figure 5. Note that the connector only fits together one way
.
To detach the connector, push down on the end of the lock arm and pull the two apar t.
Figure 3 Figure 4
Locking Tab
Male Pin
SolderOuter
Crimp T ab
Inner
Crimp T ab
Figure 5
-12-
Female Pin
Female Housing
AB
Locking Tab
SolderOuter
Crimp T ab
Inner
Crimp T ab
C
ABC
Male Housing
Lock Arm
MOUNT COMPONENTS TO PANEL
Push the illuminated switch into the hole in the top
panel with the lugs as shown in Figure Q.
Install the fuse holder with the side lug in the position
shown in Figure Q. Fasten the fuse holder in place
with the nut as shown in Figure Q. Unscrew the cap
and insert the fuse into the holder.
There is a raised area on the back side of the top
panel. Screw the spacer to the raised area by
inserting a 4-40 x 1/4” flat head screw into the hole in
the raised area from the top side of the panel (see
Figure R).
When mounting the bredboard, use the holes shown in
Figure S. Mount the bredboard with two #4 x 1/4” AB
black screws from the back side of the top panel as
shown in Figure R. The negative (blue) stripe should
be on top and the numbers reading from left to right
should start with number 1 (see Figure T). CAUTION:
Do not remove the paper backing from the back of
the bredboards. Do not over-tighten the black
screws.
Figure S
-13-
Spacer
4-40 x 1/4”
Flat Head
Screw
Top Panel
Bredboard
#4 x 1/4” AB Screws
Figure R
a
e
b
c
d
f
j
g
hi
1
5
10
ON
30VAC
+5
+12
–12
15VAC
OFF
15VAC
REGULATED
POWER SUPPLY
+
2
0
C
D
–
2
0
C
D
GND
Figure T
V
V
Back Side - Lower
Right Corner
Figure Q
Side Lug
Illuminated Switch
Top Panel
Plastic Washer
Fuse Holder
Nut
WIRE SWITCH AND FUSE HOLDER (see Figure U)
Line Cord
Slide the line cord through the back panel as shown.
Spread the three line cord wires apart 6” from the end.
Fuse
Strip the insulation off of both ends of the 6” red wire to expose 1/4” of bare wire. Pass the wire through the
1/2” diameter shrink tubing. Attach one end to the side lug on the fuse holder and then solder into place.
Pass the smooth edged line cord wire through the 1/2” diameter shr ink tubing and attach to the end lug on
the fuse holder, solder into place.
Slide the shrink tubing over the fuse holder covering both lugs. Shrink the tubing for a snug fit. You may use
a hair dryer, heat gun (at lowest setting or you will melt the tubing) or the heat emitting from your soldering
iron (do not touch the tubing or the wires with the iron).
Mount the solder lug to the side panel using a 6-32 x 5/16” screw and 6-32 nut.
Switch
Disconnect the connector for the transformer.
Pass the 6” strip of red wire (leading from the side lug of the fuse holder), the (A) and (B) black transformer
wire, and the ribbed line cord wire through the 3/4” diameter piece of shr ink tubing.
Cut the 2” section of 3/16” diameter shrink tubing in half to create two 1”sections. Slide a 3/16” diameter
piece of shrink tubing over the loose end of the red wire. Attach the red wire to lug 1 on the switch and
then solder into place.
Pass the black transformer wire labeled (B) through a 3/16” diameter piece of shrink tubing. Attach the wire
to lug 2 on the switch and then solder into place.
Slide the shrink tubing over lug 1 and lug 2 on the switch. Shr ink the tubing into place.
Strip the insulation off of the black transformer wire (A) and the ribbed edged line cord wire to expose 1/2” of
bare wire. Twist the two bare wires together. Pass the wires through the 1/4”diameter piece of shrink tubing.
Attach the wires to lug 3 on the switch and solder into place. Slide the tubing over the lug. Shrink the tubing
into place.
Slide the 3/4” diameter shrink tubing over the switch and shrink into place.
Reconnect the connector for the transformer.
-14-
Fuse Holder
6-32 Nut
Side Lug
6” Red Wire
1/2” Dia.
Shrink Tubing
3/16” Dia.
Shrink Tubing
(B) Black
Transformer Wire
Female Connector
Smooth Line
Cord Wire
Ribbed Line Cord Wire
Green Line
Cord Wire
Solder Lug
3/4” Dia. Shrink Tubing
1/4” Dia. Shrink Tubing
Switch
Figure U
Switch Pin-out
1
2
3
(A) Black
Transformer Wire
6-32 x 5/16”
Screw
-15-
RESISTANCE ANALYSIS OF POWER SUPPLY
Static testing of the power supply circuits. Do not plug the power supply into the 120VAC power supply
source until all resistance readings check out. The values given below are approximate.
See Figure O for locations of testing points.
Resistance
From To Circuit Ohms Measured
1 Right Side Panel Earth Ground less than 1Ω
2 3 On/Off Switch, Fuse Infinite (SW1 Off)
2 3 On/Off, Fuse 7Ω (SW1 On)
4 5 12V Secondary 1.5Ω
6 7 5V Secondary 1.2Ω
8 9 Variable V oltage 1.6Ω
10 GND 5-pin connector +12V Regulator Input greater than 20kΩ
11
(com) GND (VΩ)
(5-pin connector)
–12V Regulator Input greater than 20kΩ
12 GND (B1) +5V Regulator Input greater than 20kΩ
13 GND (B1) +Variable Regulator Input greater than 20kΩ
14
(com) GND (VΩ)
(5-pin connector)
–Variable Regulator Input greater than 20kΩ
25
(com) GND (VΩ)
(5-pin connector)
Voltage ADJ +20V Regulator
CCW <1Ω CW >1.4kΩ
26 GND (VΩ)
(5-pin connector)
Voltage ADJ -20V Regulator greater than 1.4kΩ
27 GND (5-pin connector) +5V Regulator GND less than 1Ω
28 GND (5-pin connector) +12V Regulator GND less than 1Ω
29 GND (5-pin connector) –12V Regulator GND less than 1Ω
10 15 +12V Regulator Input less than 1Ω
11 16 –12V Regulator Input less than 1Ω
12 17 +5V Regulator Input less than 1Ω
13 18 +Variable Regulator Input less than 1Ω
14 19 –Variable Regulator Input less than 1Ω
20 GND (5-pin connector) +Variable Regulator Output CCW 100Ω CW 2.12k
20 +20 (5-pin connector) +Variable Regulator Output less than 1Ω
21 GND (5-pin connector) –Variable Regulator Output CCW 100Ω CW 2.12k
21 –20 (5-pin connector) –Variable Regulator Output less than 1Ω
22 GND (5-pin connector) +5V Regulator Output greater than 5kΩ
22 B4 +5V Regulator Output less than 1Ω
23 GND (5-pin connector) +12V Regulator Output greater than 5kΩ
23 B3 +12V Regulator Output less than 1Ω
24 GND (5-pin connector) –12V Regulator Output greater than 5kΩ
24 B2 –12V Regulator Output less than 1Ω
5
15VAC (5-pin connector right)
15VAC less than 1Ω
4
15VAC (5-pin connector left)
15VAC less than 1Ω
+30% Note: meter lead polarity CCW - Counter Clockwise CW - Clockwise VR1 & VR2 Adjustment
20A
2A COM VΩ
VΩ
COM
Loading...