Elenco Electronics RS-400/K-37 Assembly And Instruction Manual

RESISTANCE SUBSTITUTION BOX
MODEL RS-400 / K-37
Assembly and Instruction Manual
ElencoTMElectronics, Inc.
Copyright © 1990 ElencoTMElectronics, Inc. Revised 2003 REV-G 753RS400
The Resistance Substitution Box is a convenient instrument in determining the desired resistance values in circuits under design or test. The values selected for your resistance substitution box were determined to be the most commonly used in modern solid-state circuits. The values are from 10W to 1,000kW (1 meg) in 24 steps. All resistors are 5% tolerance 1/2 watt.
PARTS LIST
If you are a student, and any parts are missing or damaged, please see instructor or bookstore. If you purchased this resistance substitution box kit from a distributor, catalog, etc., please contact Elenco Electronics (address/phone/e-mail is at the back of this manual) for additional assistance, if needed.
RESISTORS
Qty. Symbol Description Color Code Part #
1 R1 10W 5% 1/2W brown-black-black-gold 121001 1 R2 22W 5% 1/2W red-red-black-gold 122201 1 R3 47W 5% 1/2W yellow-violet-black-gold 124701 1 R4 100W 5% 1/2W brown-black-brown-gold 131001 1 R5 220W 5% 1/2W red-red-brown-gold 132201 1 R6 330W 5% 1/2W orange-orange-brown-gold 133301 1 R7 470W 5% 1/2W yellow-violet-brown-gold 134701 1 R8 680W 5% 1/2W blue-gray-brown-gold 136801 1 R9 1kW 5% 1/2W brown-black-red-gold 141001 1 R10 2.2kW 5% 1/2W red-red-red-gold 142201 1 R11 3.3kW 5% 1/2W orange-orange-red-gold 143301 1 R12 4.7kW 5% 1/2W yellow-violet-red-gold 144701 1 R13 6.8kW 5% 1/2W blue-gray-red-gold 146801 1 R14 10kW 5% 1/2W brown-black-orange-gold 151001 1 R15 22kW 5% 1/2W red-red-orange-gold 152201 1 R16 33kW 5% 1/2W orange-orange-orange-gold 153301 1 R17 47kW 5% 1/2W yellow-violet-orange-gold 154701 1 R18 68kW 5% 1/2W blue-gray-orange-gold 156801 1 R19 100kW 5% 1/2W brown-black-yellow-gold 161001 1 R20 220kW 5% 1/2W red-red-yellow-gold 162201 1 R21 330kW 5% 1/2W orange-orange-yellow-gold 163301 1 R22 470kW 5% 1/2W yellow-violet-yellow-gold 164701 1 R23 680kW 5% 1/2W blue-gray-yellow-gold 166801 1 R24 1MW 5% 1/2W brown-black-green-gold 171001
TM
Qty. Description Part #
1 PC Board 517007 1 Switch SPDT PC Mount 541103 2 Switch 12 Position 542013 2 Knob 622009 1 Case with Cover 62RS400 4 Screw 4 x 1/2” Phil A 642465 2 Nut 9mm 644102 2 Washer 9mm x 15mm 645103 1 Alligator Clip Black 680001 1 Alligator Clip Red 680002 1 Wire Black Stranded 12” 814210 1 Wire Red Stranded 12” 814215 1 Solder 9ST4
MISCELLANEOUS
-1-
PARTS IDENTIFICATION
Switch PC Mount
Switch 12 Position
9mm Nut
PC Board
Resistor
Washer
Alligator Clip
IDENTIFYING RESISTOR VALUES
Use the following information as a guide in properly identifying the value of resistors.
BAND 1
1st Digit
Color Digit Black 0 Brown 1 Red 2 Orange 3 Yellow 4 Green 5 Blue 6 Violet 7 Gray 8 White 9
BAND 2
2nd Digit
Color Digit Black 0 Brown 1 Red 2 Orange 3 Yellow 4 Green 5 Blue 6 Violet 7 Gray 8 White 9
2 Multiplier Tolerance
1
Multiplier
Color Multiplier Black 1 Brown 10 Red 100 Orange 1,000 Yellow 10,000 Green 100,000 Blue 1,000,000 Silver 0.01 Gold 0.1
BANDS
Resistance
Tolerance
Color Tolerance Silver +10% Gold +5% Brown + Red +2% Orange +3% Green + Blue +.25% Violet +.1%
1%
.5%
-2-
CONSTRUCTION
Introduction
The most important factor in assembling your RS-400 Resistance Substitution Box Kit is good soldering techniques. Using the proper soldering iron is of prime importance. A small pencil type soldering iron of 25 ­40 watts is recommended. The tip of the iron must be kept clean at all times and well tinned.
Safety Procedures
• Wear eye protection when soldering. Locate soldering iron in an area where you do not have to go around it or reach over it.
Do not hold solder in your mouth. Solder contains lead and is a toxic substance. Wash your hands thoroughly after handling solder.
• Be sure that there is adequate ventilation present.
Assemble Components
In all of the following assembly steps, the components must be installed on the top side of the PC board unless otherwise indicated. The top legend shows where each component goes. The leads pass through the corresponding holes in the board and are soldered on the foil side.
Use only rosin core solder of 63/37 alloy. DO NOT USE ACID CORE SOLDER!
What Good Soldering Looks Like
A good solder connection should be bright, shiny, smooth, and uniformly flowed over all surfaces.
1. Solder all components from
the copper foil side only. Push the soldering iron tip against both the lead and the circuit board foil.
2. Apply a small amount of
solder to the iron tip. This allows the heat to leave the iron and onto the foil. Immediately apply solder to the opposite side of the connection, away from the iron. Allow the heated component and the circuit foil to melt the solder.
3. Allow the solder to flow
around the connection. Then, remove the solder and the iron and let the connection cool. The solder should have flowed smoothly and not lump around the wire lead.
4.
Here is what a good solder connection looks like.
Component Lead
Foil
Solder
Foil
Solder
Foil
Soldering Iron
Circuit Board
Soldering Iron
Soldering Iron
Types of Poor Soldering Connections
1. Insufficient heat - the
solder will not flow onto the lead as shown.
2. Insufficient solder - let the
solder flow over the connection until it is covered. Use just enough solder to cover the connection.
3. Excessive solder - could
make connections that you did not intend to between adjacent foil areas or terminals.
4. Solder bridges - occur
when solder runs between circuit paths and creates a short circuit. This is usually caused by using too much solder. To correct this, simply drag your soldering iron across the solder bridge as shown.
Rosin
Soldering iron positioned incorrectly.
Solder
Component Lead
Solder
Soldering Iron
Foil
Gap
Drag
-3-
ASSEMBLY INSTRUCTIONS
Begin the PC board assembly with resistor R12. Be sure to identify the correct value by reading the color code. Place the resistor into the PC board with the leads coming out on the copper foil side. Solder in place and clip off the excess leads, close to the connection.
R12 - 4.7kW 5% 1/2W Resistor
(yellow-violet-red-gold)
R11 - 3.3kW 5% 1/2W Resistor
(orange-orange-red-gold)
R10 - 2.2kW 5% 1/2W Resistor
(red-red-red-gold)
R8 - 680W 5% 1/2W Resistor
(blue-gray-brown-gold)
R7 - 470W 5% 1/2W Resistor
(yellow-violet-brown-gold)
R9 - 1kW 5% 1/2W Resistor
(brown-black-red-gold)
R1 - 10W 5% 1/2W Resistor
(brown-black-black-gold)
R2 - 22W 5% 1/2W Resistor
(red-red-black-gold)
R3 - 47W 5% 1/2W Resistor
(yellow-violet-black-gold)
R5 - 220W 5% 1/2W Resistor
(red-red-brown-gold)
R19 - 100kW 5% 1/2W Resistor
(brown-black-yellow-gold)
R20 - 220kW 5% 1/2W Resistor
(red-red-yellow-gold)
R21 - 330kW 5% 1/2W Resistor
(orange-orange-yellow-gold)
R23 - 680kW 5% 1/2W Resistor
(blue-gray-yellow-gold)
R24 - 1MW 5% 1/2W Resistor
(brown-black-green-gold)
R22 - 470kW 5% 1/2W Resistor
(yellow-violet-yellow-gold)
R18 - 68kW 5% 1/2W Resistor
(blue-gray-orange-gold)
R17 - 47kW 5% 1/2W Resistor
(yellow-violet-orange-gold)
R16 - 33kW 5% 1/2W Resistor (orange-orange-orange-gold)
R14 - 10kW 5% 1/2W Resistor
(brown-black-orange-gold)
R6 - 330W 5% 1/2W Resistor
(orange-orange-brown-gold)
R4 - 100W 5% 1/2W Resistor
(brown-black-brown-gold)
R13 - 6.8kW 5% 1/2W Resistor
(blue-gray-red-gold)
R15 - 22kW 5% 1/2W Resistor
(red-red-orange-gold)
-4-
SW3 - PC Mount Switch
SW1
Mount SW3 in the place shown on the PC board. Solder into place.
Red Test Lead Black Test Lead
Cut off 1 1/2” of wire off of both the red and black wires (SAVE them for later use). Strip 1/4” of insulation off both ends of the 10 1/2” red and black wires and insert them into the holes as marked on the PC board. Solder into place. Tie a knot with both wires 1 1/2” from the surface of the PC board as shown in Figure 1. Pull the wires through the hole in the cover. Slide the alligator boots onto the wires. Solder the wires to the alligator clips. Then, slide the boots onto the clips.
SW2
Bend the tab on the switches down (see Figure 2). Attach the two switches loosely to the front panel with the 9mm nuts and washers. Line up the holes of the PC board with the switch lugs, as shown in Figure 3. Be sure that the board lays flat, then solder the lugs into place. Tighten down the 9mm nuts.
Washer
9mm Nut
Figure 3
Bend Tab Over
Figure 2
PC Board
Cover
Bend Tabs
Figure 1
Wiper Pin
Over Wire
Jumper wire from SW1 Jumper wire from SW2
Strip 1/4” of insulation off of both ends of the 1 1/2” red and black wires. Solder one end of the wire to the wiper pin on the 12 position switches and the other to the pad without a hole, as shown in Figure 4.
Installation of Knobs if an Ohm Meter is Available
Place the knobs loosely on the switch posts. Push the slide switch to the “W” position. Connect an ohm meter to the output. Line up the pointer of the knob with the value shown on your meter, then push the knob onto the shaft. Push the slide switch to the “KW” position and repeat the same procedure.
Jumper Wires
Wiper Pin
SW2
SW1
Figure 4
-5-
Installation of Knobs without an Ohm Meter
If an ohm meter is not available, turn both switches so that the wiper contact is in the position shown in Figure 5. Start with switch SW1, follow the copper run on the PC board from the lug in contact with the wiper to the 470W (R7) resistor, to be sure that the switch is set in the proper position. Align the knob on the SW1 (W) switch to the 470 position, push the knob onto the shaft. Follow the same procedure for switch SW2 (KW), except follow the copper run to the 6.8KW (R13) resistor. Align the knob on the SW2 (KW) switch to the 6.8 position.
LugPC Board
Wiper Contact
Figure 5
TESTING THE CIRCUIT
The following test is to be made with your meter to determine that the resistors are in their correct circuit positions. The resistors used in your circuit are gold banded with a tolerance of +5%. That means that a 10kW resistor could measure between 9,500W and 10,500W and be correct. Each of the 24 resistance value positions will be tested and recorded in the chart below.
SW1
Value Position Meter Reading
10W 22W
47W 100W 220W 330W 470W 680W
1000W 2200W 3300W 4700W
SCHEMATIC DIAGRAM
W
W
POSITION
W
SW2 K
Value Position Meter Reading
6.8KW 10KW 22KW 33KW 47KW 68KW
100KW 220KW 330KW 470KW 680KW
1MW
W
POSITION
-6-
ElencoTMElectronics, Inc.
150 W. Carpenter Avenue
Wheeling, IL 60090
(847) 541-3800
http://www.elenco.com
e-mail: elenco@elenco.com
Loading...