Page 1
Made in Taiwan
HDMI
TM
EXTENDER
ELE8088
INSTALLATION Manual
7.1 CH
AUDIO
7.1 CH
AUDIO
Page 2
1
Safety and Notice
The ELE8088 HDMI™ EXTENDER has been tested for conformance to safety
regulations and requirements, and has been certied for international use. However, like
all electronic equipments, the ELE8088 should be used with care. Please read and follow
the safety instructions to protect yourself from possible injury and to minimize the risk of
damage to the unit.
● Follow all instructions and warnings marked on this unit.
● Do not attempt to service this unit yourself, except where explained in this manual.
● Provide proper ventilation and air circulation and do not use near water.
● Keep objects that might damage the device and assure that the placement of this unit is
on a stable surface.
● Use only the power adapter and power cords and connection cables designed for this
unit.
● Do not use liquid or aerosol cleaners to clean this unit. Always unplug the power to the
device before cleaning.
Page 3
2
INTRODUCTION
The ELE8088 HDMITM EXTENDER boosts your audio/video transmission distance up to 60m
(200ft) in HDTV 1080i format, 40m (130ft) in HDTV 1080p format, and 20m (65ft) in HDTV
1080p with 36 bit color depth. With two cost effective solid Cat-5/5e/6 UTP/STP cable, users can
readily extend HDTV sources from DVD players, Blu-ray Disc player, PS3, PC, and any other kinds
of sources compliant with TMDS to distant display monitors including HDMITM or DVI enabled TV
sets or LCD PC monitors. The ELE8088 also features with embedded IR input and output on both
transmitting and receiving units so users can control the source device or HDMITM display at romote
site via IR remote in di-directional IR pass-through.
The ELE8088 includes two units: transmitting unit and receiving unit. The transmitting unit sends
the HDMITM or DVI signals received from the source device and receives IR signals from the
receiving unit or sends the received IR signal from the transmitting unit via two low cost Cat5/5e/6 cables. The receiving unit is responsible for equalizing the audio/video data received from
the transmitting unit and sends the IR signals received from the IR receiving to the transmitting
unit or receives IR signals from the transmitting unit . The transmission distance between the
audio/video source and the display can be up to 60m (200ft) at HD resolution (720p/1080i), or
40m (130ft) at Full HD resolution (1080p). With 8-level digital signal equalization control on the
receiving unit, users can adjust the signal level equalization scale to the received audio/video
signals, and therefore optimize the transmission distance between source and display.
Page 4
3
Features
» Support HDMITM Deep Color & full 3D
» Extends the transmission distance up to 60m (200ft) from the sources under 1080i or 720p
» Extends the transmission distance up to 40m (130ft) from the sources under 1080p
» Provides independent DDC channel, fully HDCP compliant
» Minimizes the cable skew by adjustable 8-level equalization rotary control switch
» Support bi-directional full bandwidth of IR signal, 20KHz ~ 60KHz
» Pure unaltered uncompressed 7.1ch digital HDMITM over CAT5/6 cable transmission
» Wall mounting housing design for easy and robust installation
» Only needs power supply at either transmitting or receiving unit
» Perfectly integrated with other HDMITM over Cat.X series products
The claimed transmission distance here is subject to the grade of installed cable(s),
source device and display.
For over Cat.X/COAX transmission, the cable(s) has to be solid, not stranded. Any
keystone jack along the transmission path will kill the transmission performance
signicantly!
Package Contents
» ELE8088 x1 (TX unit & RX unit) » IR blaster x1
» IR receiver x1 » DC 5V 2A wall wart x1
» Installation manual x1
Page 5
4
Specications
Model Name Transmitter Receiver
Technical
HDMITM compliance HDMITM Deep Color & full 3D
HDCP compliance Yes
Video bandwidth Single-link 225MHz [6.75Gbps]
Video support 480i / 480p / 720p / 1080i / 1080p60
HDMITM over UTP
transmission [8-bit]
Full HD (1080p)-40m (130ft) [CAT5e] / 50m (165ft) [CAT6]
HD (720p/1080i)-50m (165ft) [CAT5e] / 60m (200ft) [CAT6]
Audio support Surround sound (up to 7.1ch) or stereo digital audio
Signal equalization 8-level digital rotary switch for signal level control at receiving unit
Input TMDS signal 1.2 Volts [peak-to-peak]
Input DDC signal 5 Volts [peak-to-peak, TTL]
ESD protection
[1] Human body model — 19kV [air-gap discharge] & 12kV [contact discharge]
[2] Core chipset — 8kV
PCB stack-up 4-layer board [impedance control — differential 100Ω ; single 50Ω]
IR pass-through Half-duplex bi-directional
Input 1x HDMITM + 1x 3.5mm 2x RJ45 + 1x 3.5mm
Output 2x RJ45 + 1x 3.5mm 1x HDMITM + 1x 3.5mm
HDMITM source &
display control
Controllable via bi-directiona IR pass-through path
IR remote control Electro-optical characteristics: π = 25° / Carrier frequency: 20-60kHz
HDMITM connector Type A [19-pin female]
RJ-45 connector WE/SS 8P8C with 2 LED indicators
3.5mm connector IR sender and receiver
Rotary control switch None 8-Signal level equalization
Mechanical
Housing Metal enclosure
Dimensions
[L x W x H]
Model 3.3" x 2.9" x 1.0" (83 x 74 x 27mm)
Package 10.6" x 6.9" x 3.1" (270 x 175 x 80mm)
Carton 1'6" x 1'3" x 11.8" (450 x 370 x 300mm)
Weight
Model 14 oz (405g)
Package 2.5 lbs (1132g)
Fixedness Wall-mounting case with screws
Power supply 5V 2A DC at either transmitting or receiving unit
Power consumption 1.5 Watt (max)
Operation temperature 32~104°F (0~40°C)
Storage temperature -4~140°F (-20~60°C)
Relative humidity 20~90% RH (no condensation)
Page 6
5
INPUT/OUTPUT PANELS
Transmitting unit (TX)
Input Panel
IR-in:
3.5mm infrared socket for plugging in the extension cable of IR receiver
IR-out:
3.5mm infrared socket for plugging in the extension cable of IR blaster
HDMI IN:
Connects to a HDMITM source with a HDMITM male-male cable
output Panel
power:
Connect to 5V DC power supply unit either at the transmitting unit or the receiving
unit. Powered at one end is enough to supply the whole extender set
cats-01:
Connect a Cat-5/5e/6 cable to the CATS-01 port on the receiving unit
cats-02:
Connect a Cat-5/5e/6 cable to the CATS-02 port on the receiving unit
Page 7
6
Receiving unit (RX)
input Panel
power:
Connect to 5V DC power supply unit either at the receiving unit or the transmitting
unit. Powered at one end is enough to supply the whole extender set
cats-01:
Connect a Cat-5/5e/6 cable to the CATS-01 port on the transmitting unit
cats-02:
Connect a Cat-5/5e/6 cable to the CATS-02 port on the transmitting unit
output Panel
IR-iN:
3.5mm infrared socket for plugging in the extension cable of IR receiver
IR-OUT:
3.5mm infrared socket for plugging in the extension cable of IR blaster
HDMI OUT:
Connects to a HDMITM display or projector with a HDMITM male-male cable
EQ LEVEL:
Adjust the 8-level signal equalization control to the received HDMITM signals.
The HDMITM signal level varies from 0 (strongest) to 7 (weakest) for respective
transmission length from longest possible range to short distance. Dial the EQ from 7
to 0 and stop turning the rotary switch whenever the audio/video is playing normally.
Inappropriate signal level setting may cause overpowering issues that would shorten
the product's life signicantly!
Page 8
7
IR Extenders
IR Blaster IR Receiver
IR Sockets
IR-OUT:
plug in the IR blaster to emit all IR command signals received from the IR receiver
from the other enf to control the devices corresponding to the IR signals.
IR-IN:
plug in the IR receiver to receive all IR command signals from the IR remote controls
of the corresponding devices.
CAUTION!
Incorrect placement of IR Blaster and Receiver may result in the failure of the
IR extenders. Please check carefully before plugging in the IR extender to the
respective IR sockets. Warranty will not cover the damage.
Denition of IR Earphone Jack
IR Blaster IR Receiver
1. IR Signal [20-60KHz]
2. Grounding
1 2
1
1. IR Signal [20-60 kHz]
2. Grounding
3. Power
2 3
IR PASS-THROUGH
Page 9
8
1. Connect a HDMITM or DVI source (e.g., a Blu-ray Disc player) to the transmitting unit.
2. Connect a HDMITM or DVI display (e.g., a HDTV) to the receiving unit.
3. Connect two solid Cat-5/5e/6 UTP/STP cable between the transmitting and receiving
units.
4. Make sure these two solid Cat-5/5e/6 UTP/STP cable are tightly connected and not
loose.
5. If you want to control the source devices at display side, plug in the IR blaster to the
transmitting unit and the IR receiver to the receiving unit. If you want to control the
display at source side, plug in the IR receiver to the transmitting unit and the IR blaster
to the receiving unit.
6. Plug in the 5V DC power supply unit to the latch-locking power jack on either the
transmitting unit or the receiving unit.
7. If you see ickering or blinking image on the display, adjust the rotary control switch
to improve the cable skew. 0 stands for the strongest HDMITM signal level for longest
possible transmission length while 7 stands for the weakest HDMITM signal level for short
transmission length. Try adjusting the signal level from 7 to 0 to nd the optimal setting
for the HDMITM over CAT5 transmission.
HARDWARE INSTALLATION
PERFORMANCE GUIDE
Performance rating Type of category cable
Wiring Shielding CAT5 CAT5e CAT6
Solid
Unshielded (UTP)
Shielded (STP)
Stranded
Unshielded (UTP)
Shielded (STP)
Termination Please use EIA/TIA-568-B termination (T568B) at any time
Page 10
9
Audio/Video Port
Function
TX0-
TX0+
TX1-
TX2-
TX2+
TX1+
TXC-
TXC+
PIN
1
2
3
4
5
6
7
8
Color
W-O
O
W-G
BL
W-BL
G
W-BR
BR
Data Link TIA/EIA-568-B
W-OOW-G
JACK POSITION
PAIR3
PAIR1PAIR2PAIR4
RJ-45 Jack
G
W-BL
W-BR
BR
BL
Control Channel Port
Function
IR
Power
DDC SCL
DDC SDA
GND
GND
Power
CEC
PIN
1
2
3
4
5
6
7
8
Color
W-O
O
W-G
BL
W-BL
G
W-BR
BR
Data Link TIA/EIA-568-B
W-OOW-G
JACK POSITION
PAIR3
PAIR1PAIR2PAIR4
RJ-45 Jack
G
W-BL
W-BR
BR
BL
RJ45 / CAT5 PIN DEFINITION
Page 11
10
1. When adjusting the signal level on the receiving unit, please dial the rotary control
switch from 7 to 0 and stop turning the rotary switch whenever the audio/video is
playing normally. Inappropriate signal level setting may cause overpowering issue that
would shorten the product life signicantly!
2. Wrongly insert IR blaster and IR receiver to wrong 3.5mm infrared sockets may result in
the failure of the IR extenders. Please check carefully before plugging in the IR extender
to the respective IR sockets.
3. If the DVI or HDMITM device requires the EDID information, please use EDID Reader/
Writer to retrieve and provide DVI or HDMITM display EDID information.
4. All HDMITM over CAT5 transmission distances are measured using Belden 1583A CAT5e
125MHz UTP cable and ASTRODESIGN Video Signal Generator VG-859C & VG-870B.
5. The transmission length is largely affected by the type of Cat-5/5e/6 cables, the type
of HDMITM sources, and the type of HDMITM display. The testing result shows solid UTP
cables (usually in the form of 300m [1,000ft] bulk cables) can transmit a lot longer
signals than stranded UTP cables (usually in the form of fixed length patch cords).
Shielded STP cables are better suited than unshielded UTP cables. A solid UTP Cat5e cable shows longer transmission range than stranded STP Cat-6 cable. For long
extension applications, solid UTP/STP cables are the only viable choice.
6. EIA/TIA-568-B termination (T568B) for Cat-5/5e/6 cables is recommended for better
performance.
7. To reduce the interference among the unshielded twisted pairs of wires in Cat-5/5e/6
cable, one can use shielded STP cables to improve EMI problems, which is worsen in
long transmission.
8. Because the quality of the CAT5/6 cables has the major effect on how long the
transmission limit can achieve and how good is the received picture quality, the
actual transmission range is subject to one's choice of Cat-5/5e/6 cables. For desired
resolutions greater than 1080i or 1280x1024, a Cat-6 cable is recommended.
9. If your HDMI
TM
display has multiple HDMITM inputs, it is found that the rst HDMITM input
[HDMITM input #1] generally can produce better transmission performance among all
HDMITM inputs.
NOTICE
Page 12
11
Designed & Manufactured by
Headquarters: 9390 Veterans Memorial Parkway, O’Fallon, MO 63366
(800) 844 – 9555 / (636) 272 – 8025
(636) 272 – 8214
retailsupport@skywalker.com
Branch Ofce: 4168 North Pecos Rd, Ste 103, Las Vegas, NV 89115
(888) 319 – 3554 / (702) 632 – 3413
(702) 643 – 2379
Branch Ofce: 2445 South 179th St, New Berlin, WI 53146
(800) 444 – 9320 / (262) 786 – 5887
(262) 786 – 9031
www.skywalker.com
Loading...