elektraLite Warm White Dazer Users Manual

Elektralite

Dazer Downlight

Warm White

(Version 2.01)

USER MANUAL

(From serial number 24130).

Elektralite (a division of Group One),
70, Sea Lane, Farmingdale, NY11735, U.S.A.
T. [phone]. F. [phone]

WWW.MYELEKTRALITE.COM

1. Unpacking

Thank you for choosing the Elektralite Warm Whit e Dazer fixture. For your own safety, please read this manual before

installing the fixture. This manual covers important information on installation and applications. Please keep this manual for

future reference.

To keep this simple, we are going to refer to the fixture as the Elektralite Dazer Downlight throughout the manual.
The Elektralite Dazer Downlight fixture uses 36 high powered 5 watt leds in a balanced arrangement giving incredible output.

Please unpack it carefully and check whether it was damaged in shipping.

2. Safety Instructions.

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is

absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. The

Elektralite Dazer Downlight is a high voltage fixture. Be careful when dealing with high voltages.
Please read this manual. If you do not read this manual a nd da mages occ ur to the Elektralite Dazer Downlight, then it
could void the warranty.

During shipping, Elektralite Dazer Downlight may have been exposed to high temperature changes or humidity changes. So,
as a precaution, do not switch Elektral ite Dazer Downli ght on immediately. Condensation can damage Elektralite Dazer
Downlight so leave it switched off, until it has reached room temperature.
The electric connection must be carry out by a qualified person and it is absolutely essential that the Elektralite Dazer

Downlight be grounded. This is imperative and is a safety issue.

Always disconnect the Elektralite Dazer Downlight from the power source, when the device is not in use or before cleaning it.
Only unplug Elektralite Dazer Downlight from the power cord. Never pull out the plug out by pulling on the power cord.
Please keep the Elektralite Dazer Downlight away from children and the general public. Please be intelligent and use
common sense when operating the Elektralite Dazer Downlight.

3. General Guidelines.

The Elektralite Dazer Downlight is a lighting fixture for professional use on stages, in churches, theatres, etc.
The Elektralite Dazer Downlight should only be operated at between 120 to 240 volts and only indoors.
The Elektralite Dazer Downlight should not be operated 24/7 (24 hours a day; 7 days a week). The Elektralite Dazer

Downlight needs operation breaks to ensure that it will work for a long time without problems. Please do not shake the
Elektralite Dazer Downlight and avoid using brute force when installing or operating it.

When choosing the location to install the Elektralite Dazer Downlight, please make sure that it is not exposed to extreme
heat, moisture or dust. The minimum distance between the Elektralite Dazer Downlight and the illuminated surface must be

more than 3 feet.

Always mount the Elektralite Dazer Downlight with an appropriate safety cable/chain.
Operate the Elektralite Dazer Downlight only when you are familiar with the features on the fixture. Do not permit operation

by persons not qualified to operate it.

All modifications to the Elektralite Dazer Downlight will invalidate the warranty. There are absolutely no exceptions.
If Elektralite Dazer Downlight is operated in any way different to the one described in this manual, the Elektralite Dazer

Downlight maybe damaged and the guarantee will be void.

4. Changing Lenses.

The Elektralite Dazer Downlight comes with a set of different lenses. They are marked in a boxes. When replacing the lens

plate great care has to be taken to not damage the leds themselves. First undo the four screws holding the lens in place and

gently lift the whole lens plate off the leds. Place the new lens plate over the leds making sure the orientation of the lens plate

is correct and the lens plate fits on top of the leds. Use the four screws to attach the plate to the fixture. Take GREAT care not

to screw the screws down tightly as this will crush the leds and possibly damage the leds. Do not use any electrical

screwdriver at any torque setting. Screwing the lens plate down too tightly may not break the leds but could damage the led

terminals so that they will fail at a later date. The screw should be tightened like a car wheel but be no tighter than hand tight

plus a quarter turn. It cannot be said strongly enough to be careful and NOT tighten the screws. Led damage by interchanging

lenses is not covered under warranty in any circumstances. There is also a video on the website showing how to change lens.

5. Installation

Please ensure that the Elektr alite Dazer Downlight is hung using the appropriate "C" clamp, half cheeseboro or threaded

rod. A safety chain or cable should also be used as a secondary point of holding the fixture in case the clamp comes loose.

Never hang the fixture without a safety chain or cable. There is a ring bolt on the rear panel for the safety.

If you are not qualified or have any doubts about hanging the Elektralite Dazer Downlight then do NOT hang it.

Do not clamp the cable to the U bracket or clamp. That is not a secondary safety point.

A secondary safety point is any point that will adequately hold the Elektralite Dazer Downlight if the "C" clamp, half

cheesboro or threaded rod fails. Then the safety cable would be the backup and stop the fixture from falling to the ground. So

do NOT fix the safety to the same place that the primary point of holding is attached.

Installation during construction.

Many times fixtures are installed during the construction phase of a building. It is imperative that the fixture is protected during

this phase. A lot of dust is usually created. This dust can adversely affect the fixture. Specifically, of course, in coating the

lenses and therefore reducing the output. However much more seriously, dust, like sheetrock dust, can get inside the fan

bearings especially if the fixture is being operated during construction. Sheetrock dust, mixed with the grease of the fan motor,

will result in the fan’s premature failure and that is not covered under the fixture’s warranty. It is therefore strongly advised to

keep the fixtures covered up during the construction phase and not used.

6. Grounding.

Always make sure that there is sufficient grounding (earth) for the fixture. This is not only imperative within the circuit that the

fixture is being connected to, but also make sure there is sufficient grounding into the building. All fixtures regardless of

manufacturer have a surge at initial “turn-on”. Once initial “turn-on” is complete, the surge current (per fixture) will travel down

the ground. While each 20 Amp circuit may have the correct size of ground wire, the ground input to the building and/or

electrical panel may not be sufficient for the job. Please review this with the electrical contractor. The Elektralite Dazer
Downlight has a surge current over and above its operating current of approximately 2 Amp at 120 volts. If an installation has

100 Dazers that means 200 Amps needs to be dissipated through the GROUND WIRING. If there is a lack of a sufficiently big

enough ground cable into the building or on the individual circuits it can cause severe damage to the fixture and this is not

covered under the warranty.

One further check : the ground to neutral voltage for each circuit. In a lot of buildings, voltages across these can damage

fixtures or cause operational problems both for the fixture and DMX.

Please review these two important points with a qualified electrical contractor. If in any doubt, have an independent qualified

third party electrical contractor check the installation, well before commencing installation.

Circuit Limitation :-

There should be no more than 5 Dazer Downlights on a 20 amp 120 volt circuit, having no other load on it. That means to
say a, maximum of 5 Dazer Downlights are on a 20 amp 120 volt circuit with nothing else plugged into that circuit.

7. DMX-512 Control and Power input Connections

Once the cover plates have been removed from the rear panel, there are two terminal blocks.

Please refer to the picture above for wiring layout.

DMX signal consists of three wires. Those are Data+, Data- and screen.

Power Input consists of three wires Ground (G), Neutral (N) and Live (L).

Note :- We strongly advise you take one of the Elektralite Dazer Downlights

many multiple units. This way the correct wiring is achieved and the fixture works on DMX. If you do not do this you are liable

to have all your fixtures up in the ceiling and the DMX wiring is wrong. That is a lot of wasted time. So check the DMX wiring

and make sure the first fixture works from the control console.

The holes in the cover plate are standard 3/8” so the appropriate clamp for the cabling may be purchased at Home Depot,

Lowes or electrical shop.

and check the DMX wiring before hanging

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically “noisy” environment, it is

recommended that a DMX terminator is used. This helps prevent corruption of the digital control signal. The DMX terminator

is simply a 120 Ω resistor connected between Data + and Data -. The terminator is positioned on the DMX output side of the

last fixture in the dmx chain.