elektraLite Dazer RGB User Manual

Elektralite LED Pro Line

RGB Dazer

(Version 2).

USER MANUAL

Elektralite (a division of Group One),
70, Sea Lane, Farmingdale, NY11735, U.S.A.
T. [phone]. F. [phone]

WWW.MYELEKTRALITE.COM

1. Unpacking

Thank you for choosing the Elektralite Led Pro Line RGB Dazer fixture. For your own safety, please read this manual before

installing the fixture. This manual covers important information on installation and applications. Please keep this manual for

future reference.

To keep this simple, we are going to refer to the fixture as the Elektralite Led Pro Line RGB Dazer throughout the manual.
The Elektralite Led Pro Line RGB Dazer fixture uses 36 high powered 5 watt leds in a balanced arrangement giving

incredible output. Please unpack it carefully and check whether it was damaged in shipping.

The following items should be in the box with the fixture:-

Color/Gel frame

2. Safety Instructions.

This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe operation, it is

absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual. The

Elektralite Led Pro Line RGB Dazer is a high voltage fixture. Be careful when dealing with high voltages.
Please read this manual. If you do not read this manual and damages occur to the Elektralite Led Pro Line RGB Dazer,
then it could void the warranty.

During shipping, the Elektralite Led Pro Line RGB Dazer may have been exposed to high temperature changes or humidity
changes. So, as a precaution, do not switch the Elektralite Led Pro Line RGB Dazer on immediately. Condensation can
damage the Elektralite Led Pro Line RGB Dazer so leave the Elektralite Led Pro Line RGB Dazer switched off until it has
reached room temperature. The Elektralite Led Pro Line RGB Dazer is an INDOOR operational fixture. Do not operate this
fixture outdoors or anywhere there is high humidity.
The electric connection must carry out by a qualified person and it is absolutely essential that the Elektralite Led Pro Line
RGB Dazer be grounded. So under no circumstances break off the ground pin on the Edison plug or use the fixture where a
ground is not present. A ground pin, like the fuse for the Elektralite Led Pro Line RGB Dazer is there for safety.

Always disconnect the Elektralite Led Pro Line RGB Dazer from the power source, when the fixture is not in use or before
cleaning it. Elektralite Led Pro Line RGB Dazer Never pull out the Edison plug out by just pulling on the power cord itself.

Please keep the Elektralite Led Pro Line RGB Dazer away from children and the general public. Please be intelligent and
use common sense when operating the Elektralite Led Pro Line RGB Dazer.

3. General Guidelines.

Elektralite Led Pro Line RGB Dazer is a lighting fixture for professional use on stages, in clubs, theatres, churches etc.
Elektralite Led Pro Line RGB Dazer should only be operated at between 120 to 240 volts and only indoors.
Elektralite Led Pro Line RGB Dazer should not be operated 24/7 (24 hours a day; 7 days a week). Elektralite Led Pro Line
RGB Dazer needs operation breaks to ensure that it will work for a long time without problems. Please do not shake the
Elektralite Led Pro Line RGB Dazer and avoid using brute force when installing or operating it.

When choosing the location to install the Elektralite Led Pro Line RGB Dazer, please make sure that it is not exposed to

extreme heat, moisture or dust and never install it outdoors. Make sure that the fixture has a good amount of free space

around it for air flow. Do not install it in a confined space or have insulation around the fixture. The minimum distance between

the Elektralite Led Pro Line RGB Dazer and the illuminated surface must be more than 3 feet.
Always mount the Elektralite Led Pro Line RGB Dazer with an appropriate safety cable.
Operate the Elektralite Led Pro Line RGB Dazer only when you are familiar with the features on the fixture. Do not permit

operation by persons not qualified.

All modifications to the Elektralite Led Pro Line RGB Dazer will invalidate the warranty. There are absolutely no
exceptions.
If Elektralite Led Pro Line RGB Dazer is operated in any way different to the one described in this manual, Elektralite Led

Pro Line RGB Dazer maybe damaged and the guarantee will be void

4. Installation

Please ensure that the El ektralite Led Pro Line RGB Dazer is hung using the appropriate "C" clamp or half cheeseboro. A

safety chain or cable should also be used as a secondary point of holding the fixture in case the clamp comes loose. Never

hang the fixture without a safety chain or cable. Make sure the Gel frame (Gel holder) is clipped into position correctly and

cannot come loose.

If you are not qualified or have any doubts about hanging the Elektralite Led Pro Line RGB Dazer then do NOT hang it.

Do not clamp the safety cable to the U bracket or clamp. That is not a secondary safety point.

A secondary safety point is any point that will adequately hold the Elektralite Led Pro Line RGB Dazer if the "C" clamp or
half cheesboro fails. Then the safety cable would be the backup and stop the fixture from falling to the ground. So do NOT fix
the safety cable to the same place that the "C"clamp is attached

5. DMX-512 Control Connection

Ω

Connect an XLR cable to the female 5-pin XLR output of your Elektralite CP 20 or other DMX controller. The other end
should be connected to the male 5-pin XLR input of the Elektralite LED Pro LineRGB Dazer. Then daisy-chain out of the first
Elektralite LED Pro Line RGB Dazer into the next Elektralite LED Pro Line RGB Dazer or other dmx device. Never “Y”

split the DMX connection.

If you need more cable, then it should be two core, screened cable fitted with a 5 pin XLR input and output connector. Please

refer to the diagram below

1

5

4

2

3

DMX-512 connection with DMX terminator

For installations where the DMX cable has to run a long distance or is in an electrically “noisy” environment, it is

recommended that a DMX terminator is used. This helps prevent corruption of the digital control signal. The DMX terminator

is simply a 5 pin XLR plug (male) with a 120 Ω resistor connected between pins 2 and 3. It is then plugged into the output XLR

socket of the last Elektralite RGB Dazer or other dmx device in the chain. Please see illustration below.

5

4

1

2

3

120

6. Menus in the fixture.

Root Menu Sub Menu 1 Sub Menu 2

STAT (STATIC LOOK) R(ED) 0-255

G(REEN) 0-255

B(LUE) 0-255

S(STROBE) 0-255

AU T O (A U TOM AT I C) AT 0 1 TH R O UGH TO AT1 0

PR 01 THROUGH TO PR10

RUN DMX

SLAV(E)

DMX ASSIGN DMX CHANNEL 1-512

PERS (PERSONALITY) STAG(E)

ARC1

AR1 D

AR1 S

HSV

ID ID 01 THROUGH 255

EDIT PR01 SC01 THROUGH TO SC99

(MAKING OWN AUTO PR02 SC01 THROUGH TO SC99

SCENES) PR03 SC01 THROUGH TO SC99

PR04 SC01 THROUGH TO SC99

PR05 SC01 THROUGH TO SC99

PR06 SC01 THROUGH TO SC99

PR07 SC01 THROUGH TO SC99

PR08 SC01 THROUGH TO SC99

PR09 SC01 THROUGH TO SC99

PR10 SC01 THROUGH TO SC99

SET UPLD

DV

RGBW

DIM

ID

REST (RESET)

CAL1 WT01 THROUGH TO WT11

CAL2 RGB

KEY OFF

ON

Password required See 15. KEY