Elektra Beckum FB 2200 HVLP, FB 150, SB 200, FB 2200 Operating And Maintenance Instructions Manual

®
115 366 5450 / D/ENG/F/NL/IT/ES/DA/SV / 1001 - 1.2
Betriebs- und Wartungsanleitung für Farbspritzpistole
Operating and Maintenance Instructions Paint Spray
Notice d’utilisation et d’entretien du pistolet à peinture
Gebruikers- en onderhoudshandleiding voor Verfspuitpistool
Manual de servicio y mantenimiento para Pistola pulverizadora
Betjenings- og betjeningsvejledning for sprøjtemalepistol
Anvisningar för drift och skötsel av färgspruta
FB 2200 HVLP FB 2200 FB 150 SB 200
D
FB 2200 HVLP Best.-Nr. 090 105 4460 FB 2200 Best.-Nr. 090 105 4452 FB 150 Best.-Nr. 090 100 3874 SB 200 Best.-Nr. 090 100 3882
ENG
F
NL
IT
ES
DA
SV
FB 2200 HVLP - FB 2200 - FB 150 - SB 200
Item Description
1 Trigger 2 Air inlet 3 Flow cup/siphon cup 4 Fluid regulating screw 5 Air control valve 6 Adjusting screw for round and wide spray pattern 7 Nozzle 8 Quick-release clamp for cup
1
7
3
1
2
3
4
4
8
6
6
2
7
FB 2200 HVLP FB 150 SB 200 FB 2200
6
7
1
2
3
5 4
1. Getting to Know Y our Paint Spray Gun FB 2200 HVLP, FB 2200, FB 150 and SB 200
ENG
Contents
1. Getting to Know Your Paint Spray Gun FB 2200 HVLP , FB 2200, FB 150 and SB 200
2. Please Read First!
3. Specified Conditions of Use
4. Safety Instructions
5. Initial Operation
6. Care and Maintenance
7. Specifications
8. Standard Delivery
9. Accessories
The paint spray gun is not suitable for treatment of foods or medicines.
Do not smoke, strike sparks or light fires.
Ensure good ventilation of the work area.
Wear protective clothing, especially respiratory equipment with activated carbon filter.
Do not use the paint spray gun for any purpose it was not designed for.
Be careful when handling inflammable materials.
Keep air tools out of the reach of children.
Always be rested and concentrated when wor­king with the paint spray gun.
Never direct the paint spray gun against other persons or animals.
Connect to pressurised air supply only with a quick coupler.
Working pressure must be set by means of a filter/ pressure regulator.
Do not use oxygen or fuel gas as energy source.
Disconnect from air source before servicing.
Solvents and residue paint must be disposed of in an environmetally friendly manner.
2. Please Read First
3. Specified Conditions of Use
These Paint Spray Guns are handy, air-powered paint spray guns for use in DIY and trade. They are especially suitable for spraying larger objects. The air stream atomises the spraying material into very fine particles, resulting in excellent paint transfer and a high quality finish. The spray pattern is ad­justable from round to wide (item 6) and can be adopted to the object to be sprayed. For larger objects, the nozzle adjusts steplessly from horizontal to vertical pattern. The amount of paint can be proportioned by means of the fluid regulating screw (item
4), making these spray guns very versatile. Special feature of the HVLP version: The HVLP (high volume low pressure) system reduces the paint consump­tion and increases material transfer. Savings of up to 30% in spraying material are possible. When working with the HVLP system it is impor­tant not to exceed the max. pressure of 2.6 bar.
Read instructions before commissioning, especi­ally the safety instructions.
If you notice transport damage while unpacking, notify your supplier im­mediately . Do not operate the air tool!
Dispose of the packing in an environmentally friend­ly manner. Take to a pro­per collecting point.
Keep instructions for future use.
If you lend or sell this air tool be sure to have the instructions to go with it.
4. Safety Instructions
Protect yourself and your en­vironment by suitable pre­cautions against dangers of accident.
5. Initial Operation
Connect the paint spray gun to a suitable pressurised air source by means of a flexible air hose fitted with a quick coupler. Set the filter pres­sure reducer of the pressuri­sed air source to the required working pressure (max. 5 bar). Follow the paint manu­facturer’s instructions for preparing the spraying material. Too much working pressure causes a very fine spraying material atomisa­tion with rapid evaporation, resulting in a rough surface finish and poor bonding. If the air pressure is too low, the spraying material will be insufficiently atomised, resulting in rippled surfaces and drip marks. The paint spray gun is operated by pulling the trigger (item 1). Always hold paint spray gun at even distance to object, distance should be approx. 15 cm.
Spray pattern adjuste­ment:
With the spray pattern adjusting screw (item 6) the spray gun can be set to spray a round or wide pattern. Use a round spray pattern for small areas, corners and edges and the wide horizontal or vertical pattern for large areas. The amount of spraying material is set with the fluid regulating screw (item 4). Open the fluid regulating screw by approx. 2 to 21/2 turns and make a spray test. Additional opening of the fluid regulating screw increases fluid flow and thus the spray speed. Closing the fluid regulating screw reduces the fluid flow and the spray speed. Because of the great variety of spraying materials fluid flow adjustment should always be made when spraying.
Round spray
patterns
Wide (vertical) spray patterns
6. Care and Maintenance
Thoroughly clean and ser­vice the paint spray gun after each use. Do not use solvents con­taining halogenated hydro­carbon (trichlor methyl, ethyl chloride, etc.), which could resolve some of the spray gun’s materials and lead to dangerous reactions. A cleaned spray gun will perform trouble-free when used the next time. Periodically all moving parts should be lightly oiled. If the nozzle is removed for clea­ning, its threads and gasket should be greased before reassembly. Do not use lubricants contai­ning silicone. Caution: Do not immerse complete spray gun in sol­vent! Nozzle and valve needle are wearing parts. It is recom­mended you keep a replace­ment nozzle kit on hand (see chapter 9 „Accessories“). Store your air tools in dry rooms only.
7. Specifications
9. Acessories
Nozzle Kit Ø 1.2 mm FB 2200 Stock-no. 090 105 4649 Nozzle Kit Ø 1.5 mm FB 2200 Stock-no. 090 105 4657 Nozzle Kit Ø 1.8 mm FB 2200 Stock-no. 090 105 4665 Nozzle Kit Ø 2.0 mm FB 2200 Stock-no. 090 105 4673 Nozzle Kit Ø 1.2 mm FB 150 and SB 200 Stock-no. 090 102 6858 Nozzle Kit Ø 1.5 mm FB 150 and SB 200 Stock-no. 090 102 6866 Nozzle Kit Ø 1.8 mm FB 150 and SB 200 Stock-no. 090 102 6874 Nozzle Kit Ø 2.0 mm FB 150 and SB 200 Stock-no. 090 102 6882 Other nozzle kit sizes for FB 2200 HVLP on request
8. Standard Delivery
Paint Spray Gun Instructions
FB 2200 HVLP FB 2200 FB 150 SB 200
Air consumption 100 - 200 l/min 100 - 200 l/min 150 - 260 l/min 150 - 260 l/min Working pressure 2,6 bar 3 - 5 bar 3 - 5 bar 3 - 5 bar Nozzle size Ø 1.5 mm Ø 1.5 mm Ø 1.5 mm Ø 1.5 mm Flow cup 0.5 l 0.5 l 0.5 l Siphon cup - - - 1.0 l Weight 0.6 kg 0.6 kg 0.5 kg 0.7 kg Weight, tool only 0.54 kg 0.54 kg 0.48 kg 0.67 kg Recommend inner air hose diameter 9 mm 9 mm 9 mm 9 mm Spray pattern adjustment round & wide round & wide round & wide round & wide
Pressurised air required: clean, free of oil and condensate
Elektra Beckum AG,
Daimlerstraße 1, D-49716 Meppen
Tel.: +49-1803-333 456, Fax: +49-1803-333 457=Metabo Power Tools Pty. Ltd., 28 Laser Drive,
Rowville, 3178, Victoria, Australia,
Phone: 03 9764 1933, Fax: 03 9764 1958
Metabo UK Ltd., 25 Majestic Road, GB-SO 16 OYT
Tel.: +44-2380-732 000, Fax: +44-2380-747 500Lurem MACHINES à BOIS,
Zone Industriell/BP 1, F-617000 Domfront
Tel.: +33-2-333 757 00, Fax: +33-2-333 720 70Metabo Belgium, t Hofveld 3-5,
B-1702 Groot Bijgaarden
Tél.: +32-2-467 32 10, Fax: +32-2-466 75 28,
e-mail: ldriesmann@metabo.beMetabo Nederland b. v.,
Keulschevaart 8, NL-3621 MX Breukelen,
Postbus 180, NL-3620 AD Breukelen,
Tel.: +31-3462-642 44, Fax: +31-3462-635 54,
e-mail: marianne@metabo.nlMetabo (Schweiz) AG, Kundendienst,
Lindaustrasse 17, 8317 Tagelswangen
Tel.: +41-52-354 34 44, Fax: +41-52-354 34 45,
e-mail: service@metabo.ch
www.elektra-beckum.chCarlo Stechel & Figli S.R.L.,
Via Buozzi 22, I-20097 San Donato Milanese (MI)
Tel.: +39-02-556 001 11, Fax: +39-02-556 003 22,
e-mail: a.casano@stechel.it
Herramientas Metabo, S.A.,
Polígono Ind. N°6, Parcela 16,
E-28935 Móstoles (Madrid)
Tel.: +34-91-616 57 67, Fax: +34-91-616 43 55,
e-mail: metabo-madrid@accesosis.es
Kestra S.A. Soldadura,
Polg. Ind. La Ferreria, C.Del Treball, No. 19,
E- 08110 Montcada I Reixac,
Tel.: +34-935-750 030, Fax: +34-935-753 394Bolas - Máquinas e Ferramentas de Qualidade, S.A.,
Rua 8, Lotes 8, 10, 12, P.O. Box 53,
P-7001 Évora-Codex
Tel.: +351-66-74 93 00, Fax: +351-66-74 93 09,
e-mail: bolas@mail.telepac.ptMetabo Danmark A/S,
Marielundvej 48 C, DK-2730 Herlev
Tel.: +44-84-13 55, Fax: +44-84-86 04,
e-mail: brasmus@post10.tele.dk
Profilma-Import A/S,
Postboks 536 Nanset, Sophus Buggesvei 48,
N-3252 Larvik
Tlf.: +47-33-114 777, Fax: +47-33-114 108!HDF-Paulsson AB,
Box 525, Svaravaregatan 5, S-30180 Halmstad
Tel.: +46-35-154 400, Fax: +46-35-121 780Nofa OY, P.O.Box 28,
Hannuksentie 1, FIN-02270 Espoo
Tel.: +358-9-804 851, Fax: +358-9-809 4858EB- Polska,
Spółka z o.o.J.V., ul. Gdyńska 28,
PL-73110 Stargard Szczeciński
Tel.: +48-91-578 47 72, Fax: +48
-
91-578 47 72
0
EB Nefro KFT,
Futo U. 70, HU-3508 Miskolc
Tel.: +36-46-362 264; +36-46-366 363,
+36-30-450 618, Fax: +36-46-362 761)Extra Industrial Goods,
Rr. Fadil Rada 88, AL-Tirana
Tel.: +355-42-330 62, Fax: +355-42-330 63-AS Mecro,
Peterburi tee 44, EST-11415 Tallinn
Tel.: +372-6-201 101, Fax: +372-6-201 112:ITA Ltd.,
Balakirevskij Pereulok 19, str. 1, RUS-Moscow
Tel.: +7-95-737 93 11; +7-95-737 93 12,
+7-95-737 93 13, Fax: +7-95-737 93 14,
e-mail: ita1@online.ru+Metabo s.r.o.,
Kralovicka 544, CZ-25001 Brandys nad Labem
Tel.: +42-202-804 458, Fax: +42-202-804 456,
e-mail: Miranda@metabo.cz,
Internet: http://www.metabo.cz
;
Remtech Spol. S.R.O.,
Vinice 293, SK-90021 Svaty Jur
Tel.: +42-1-744 971 981, Fax: +42-1-744 971 291
Agent Trade, S. C., S.R.L.,
Aleea Bran Nr. 2, BL. 92, P., Ap. 47,
RO- 751552 Bucuresli 4
Tel.: +40
-
13-217 445, Fax: +40-13-214 505
Dilex d.o.o.,
Orginceva ut. 17, SLO-51113 Ljublijana
Tel.: +386-61-168 16 20, Fax: +386-61-168 16 16
EB_Adr3B.fm
EB_Adr3B.fm Seite 2 Mittwoch, 21. März 2001 3:16 15
Loading...