SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
AVIS: RISQUE DE CHOC ELECTRIQUE. NE PAS OUVRIR.
WARNING: CONNECT ONLY TO MAINS SOCKET WITH PRO-
TECTIVE EARTHING CONNECTION.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance with the manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the manufacturer.
12. Unplug this apparatus during lightning storms or when unused for long periods of time.
13. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate
normally, or has been dropped
14. To completely disconnect AC power from this apparatus, the power supply cord must be unplugged.
15. Do not expose this apparatus to dripping or splashing and ensure that no objects filled with liquids, such as vases, are placed on this apparatus.
16. The AC plug of the power supply cord shall remain readily operable.
The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral triangle is intended
to alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying the appliance.
The asterisk within an equilateral triangle is intended to inform
the user to necessary installation or removal instructions regarding equipment or hardware use relating to the system.
• Electro-Voice does not recommend use of ZxA1 speakers outdoors in direct exposure environments.
• Electro-Voice ZxA1 loudspeakers are easily capable of generating sound pressure levels sufficient to cause permanent hearing damage to anyone within normal coverage distance. Caution
should be taken to avoid prolonged exposure to sound pressure levels exceeding 90 dB.
• For trouble-free operation, exceeding a maximum ambient temperature of +40°C (104°F) is
not permissable.
This is a Class A product according to FCC rules. In a domestic environment this product may cause
radio interferences in which case the user may be required to take adequate measures.
Management of WEEE (waste electrical and electronic equipment) (applicable in Member
States of the European Union and other European countries with individual national policies
on the management of WEEE) The symbol on the product or on its packaging indicates that
this product may not be treated as regular household waste, but has to be disposed through
returning it at an Electro-Voice dealer.
2
Electro-Voice® ZxA1 Owner’s Manual
Page 3
FCC Information
1. IMPORTANT: Do not modify this unit! Changes or modifications not expressly approved by the manufacturer could void the user’s authority, granted by the FCC, to operate the equipment.
2. NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in
a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Table of Contents
Important Safety Instructions ...........................................................................................................................................2
System Features - ZxA1 ....................................................................................................................................................4
Rotating the 90° Horn ........................................................................................................................................................7
Rotating the Logo ...............................................................................................................................................................7
Frequency Response ...................................................................................................................................................... 11
ZxA1 Models and Accessories Reference Table .....................................................................................................11
Electro-Voice® ZxA1 Owner’s Manual
3
Page 4
Description
Thank you for choosing the Electro-Voice ZxA1 loudspeaker system. Please take time to consult
this manual so that you can understand all the features built into your EV system and fully utilize
all its performance capabilities.
The Electro-Voice ZxA1 powered loudspeaker is a fully integrated audio system with carefully matched
electronics and transducers. This product makes it easy to setup a high quality sound system quickly
with a minimum amount of cables and external electronics.
System Features - ZxA1
• Two-way loudspeaker with EV8L 8” Woofer and DH2005 Titanium Compression Driver
• Rotatable High Frequency Waveguide with Two Coverage Patterns: 90° x 50° or 100° x 100°
• Integrated Amplifier with 800W Total Output
• Biamplified Design with 24 dB/Octave Filter Slopes and Transducer Protection
• Selectable 100 Hz High Pass Filter for use with an External Subwoofer
• XLR and 1/4“ TRS Combo Input
• XLR Microphone Input with Gain Control
• XLR Parallel Output
• LED Indicators for Power On and Limit
Specifications
Freq. Response1 (-3 dB):60 Hz - 20 kHz
Freq. Range1 (-10 dB):48 Hz - 20 kHz
Max. Calculated SPL:123 dB
Horizontal Coverage:90° or 50°100°
Vertical Coverage:50° or 90°100°
Amplifier Power Output:800W
LF Transducer:EV8L, 203mm (8 in) Driver
HF Transducer:DH2005, 25mm (1 in) Exit Compression Driver
Crossover Frequency:1.8 kHz
High Pass Frequency:100 Hz, User Selectable
Power Requirement (120V):95V - 132V, 50 - 60 Hz, 0.6A
Power Requirement (230V):190V - 264V, 50 - 60 Hz, 0.4A
Dimensions (H x W x D):457mm x 282mm x 264mm (17.98” x 11.12” x 10.38”)
Net Weight:19.0 lbs (8.6 kg)
Shipping Weight:22.7 lbs (10.3 kg)
1
4
Full Range Mode.
ZxA1-90ZxA1-100
Electro-Voice® ZxA1 Owner’s Manual
Page 5
Tripod and Floor Monitor Operation
Floor Monitor
Electro-Voice ZxA1 loudspeakers may be used as a floor monitor by placing the speaker on the integral
monitor angle. Make sure to:
• Place the speaker on a level, stable surface that is solid and secure.
• Route cables and position the stand so that performers, production crew and audience members
will not trip over the stand or cables and pull the speaker system over. Secure cables with wire
ties or tape whenever possible.
Tripod
Electro-Voice ZxA1 speakers include 35mm (1-3/8 inch) stand mounts to allow mounting on tripod
stands. Make sure to:
• Check the specifications of the speaker stand to be certain it is capable of supporting the weight of
the speaker.
• Check that the speaker stand is placed on a flat, stable surface and be sure to fully extend the
legs of the stand. Do not try to make the stand “taller” and compromise its structural integrity.
• Route cables and position the stand so that performers, production crew and audience members
will not trip over the stand or cables and pull the speaker system over. Secure cables with wire
ties or tape whenever possible.
• Do not attempt to suspend more than one speaker on a stand designed for a single speaker
• Unless you are confident that you can safely handle lifting the weight of the speaker onto the
stand, ask another person to help you place it.
• Tighten the set screw to minimize rattling and to
prevent the speaker from rotating during use.
Set Screw
Pole Mount Recess
Figure 1:
ZxA1 Monitor Position
Electro-Voice® ZxA1 Owner’s Manual5
ZxA1 Pole Mount Location
Figure 2:
Page 6
Suspending ZxA1 Loudspeakers
Electro-Voice ZxA1 loudspeakers may be safely suspended with single stud fittings by using the MP1
suspension kit, or quickly attached to a truss by using the CA-Zx truss clamp adaptor (both sold seperately). See MP1 or CA-Zx instruction sheets for proper assembly and use.
WARNING: Suspending any object is potentially dangerous and should only be attempted by
individuals who have a thorough knowledge of the techniques and regulations of rigging objects overhead. Electro-Voice strongly recommends that ZxA1 speakers be suspended taking
into account all current national, federal, state and local regulations. It is the responsibility of the
installer to ensure that ZxA1 speakers are safely installed in accordance with all such regulations. If ZxA1 speakers are suspended, Electro-Voice strongly recommends that the system be
inspected at least once a year. If any sign of weakness or damage is detected, remedial action
should be taken immediately. There are instruction sheets for each EV Suspension and Array Kit
that should also be consulted prior to suspending speakers.
Figure 3:
MP1-B Mounting Plate Accessory
6
CA-ZX Truss Clamp Accessory
Figure 4:
Electro-Voice® ZxA1 Owner’s Manual
Page 7
Rotating the 90° Horn
The 90° version of the ZxA1 allows for the horn to be rotated for more effective coverage if desired. The
horn is factory-installed with the 90° coverage in the horizontal plane and the 50° coverage in the vertical
plane. The 100° version of the ZxA1 has the same coverage pattern in both the
horizontal and vertical planes, so rotating the horn will not change the
coverage pattern. To rotate the horn follow the steps below:
1. Remove the grille screws / grille assembly.
2. Remove the horn screws / horn assembly.
3. Rotate the horn assembly 90°.
4. Secure the horn assembly with the
horn mounting screws.
5. Secure the grille assembly
with the grille mounting
screws.
Grille Mount
Screws
90° x 50°
Horn
Horn Mount
Screws
Enclosure
Grille
Assembly
90° x 50°
Horn
Figure 5:
Rotating the ZxA1-90 Horn
Rotating the Logo
All versions of the ZxA1 allow for the logo badge to
be rotated if desired. The logo badge is square and
can be rotated in 90° increments. To rotate the logo
badge, follow the steps below:
1. Using a finger or flat-edge screwdriver (using care
not to scratch grille), grip under the logo badge.
2. Pull the logo badge outwards from the logo recess until it fully clears the front surface of the grille.
3. Rotate the logo badge, in 90° increments, to the
desired orientation.
4. Release the logo badge and let it “spring” back
into the logo recess.
Electro-Voice® ZxA1 Owner’s Manual7
Rotating the ZxA1 Logo
Figure 6:
Page 8
Amplifier Controls
Quick Setup
To get the ZxA1 into operation as quickly as possible, please observe the following steps and precautions:
• Make sure power switch is in the off position before plugging in power cord.
• Plug the 3-terminal IEC-standard AC cable into a grounded line receptacle. Extension cords can be
used to lengthen the AC cable as necessary but make sure that they are 3-conductor cables of the proper
gauge, and that they are properly grounded to avoid electrical hazards and extraneous noise.
• Be sure that the ZxA1 is plugged into an AC power source that is capable of supplying the correct voltage. If the line voltage drops too much, the built-in amplifiers won’t be able to develop their rated power
and sound quality will suffer.
• Under high signal conditions, the 120V ZxA1 amplifier can draw 0.6 amps of current (0.4 amps at
230V). Be cautious of what else is plugged into the same electrical service line to avoid electrical problems and poor performance.
CAUTION: Before turning the power on, make sure that the level controls are down to avoid transients or
unexpected loud sound.
Figure 7:
ZxA1 Amplifier Panel
Electro-Voice® ZxA1 Owner’s Manual8
Page 9
Amplifier Controls (cont’)
MASTER
Level control for adjusting the power amp’s overall amplification. The
level control affects the volume of the line input and microphone input. To
prevent distortion and clipping of pre-linked mixing consoles, the control
should generally be set to a value between 0dB and +6dB.
LIMIT
The LED brief blinking indicates that the power amplifier is operated at
its limits. Short-term blinking is uncritical, because the integrated limiter
keeps distortion under control. Constant lighting of the LED indicates that
the sound is negatively affected. Reducing the output volume is strongly
recommended.
WITH SUB/FULLRANGE
When depressed, activates a 100 Hz highpass for use with a subwoofer,
or if the ZxA1 is used as a floor monitor. A pen or paperclip is needed to
depress the switch to WITH SUB mode.
MASTER OUT
Output connector to send the signal to another speaker or subwoofer.
The output is the sum of both the MIC IN and LINE IN.
LINE IN
Electronically balanced input for the connection of high-level signal sources like mixing consoles or signal processors. Connections can be established using 1/4” TRS or XLR-type connectors.
MIC
Level control for adjusting the microphone input level independent of the
master level.
MIC IN
XLR input for low level signals like microphones. The MIC IN and LINE IN
may both be used at the same time as a 2-channel mixer.
POWER
AC switch for switching the ZxA1’s power ON or OFF. The LED lights
after turning the power ON. If the LED is not lit upon turning the power on,
make sure that the AC cord is correctly connected and the outlet is properly working.
MAINS IN
AC connection is established via an IEC-connector. A 10’ (3m) long AC
cord with fitting IEC-plug is supplied. For 120V operation, the AC voltage
must be 95V - 132V. For 230V operation, the AC voltage must be 190V
Figure 8:
ZxA1 Amplifier Controls
Electro-Voice® ZxA1 Owner’s Manual9
- 264V. Locking IEC power cords may also be used.
Page 10
Dimensions
Top View
Bottom View
Block Diagram
Front View
Right View
Rear View
Electro-Voice® ZxA1 Owner’s Manual10
Page 11
20000
10000
1000
1005020
30
40
50
60
70
80
90
100
110
Frequency (Hz)
Sensitivity (dB)
Full Range Mode
With Sub Mode
20000
10000
1000
1005020
30
40
50
60
70
80
90
100
110
Frequency (Hz)
Sensitivity (dB)
Full Range Mode
With Sub Mode
Frequency Response Graphs
ZxA1-100 Series Frequency ResponseZxA1-90 Series Frequency Response
ZxA1 Models and Accessories Reference Table
System ModelCoverageFinishVoltagePart No.
ZxA1-90B (120V)90° x 50°Black120VPRD000261-001
ZxA1-90W (120V)90° x 50°White120VPRD000261-002
ZxA1-100B (120V)100° x 100°Black120VPRD000261-003
ZxA1-100W (120V)100° x 100°White120VPRD000261-004
ZxA1-90B (230V)90° x 50°Black230VPRD000261-005
ZxA1-90W (230V)90° x 50°White230VPRD000261-006
ZxA1-100B (230V)100° x 100°Black230VPRD000261-007
ZxA1-100W (230V)100° x 100°White230VPRD000261-008
Accessory ModelDescriptionPart No.
MP1-BMounting Plate Kit, Black Finish301916-001
CB1Carrying Bag, Convertible, Black Finish301917-001
SC-ZX1Slip Cover, Black Finish301919-001
CA-ZXTruss Clamp Adapter, Black Finish302023-001
TSS-1Tripod Speaker Stand302053-001
TSP-1(2) TSS-1 Tripod Speaker Stands with Carrying Case302053-000