Electro-Voice XI-1152A94F EDS User Manual

Key Features:

• Very-Compact/High-Level, Two-Wa y Design

• EVX155 15” Woof er with 4” Voice Coil

• ND6-16 3” Diaphragm HF Compression
Driver

• 90° x 40° Coverage Pattern

• Fully Rotatable HF Section for Vertical or
Horizontal Suspension

• Built-In L-Track Rigging on T op and Bottom

• Ring-Mode Decoupling / RMD

• Integrated Stand Mount

• Available in Blac k and White

TM

Xi-1152A/94F

15-Inch Two-Way,

Full-Range 90° x 40°

Sound Reinforcement System

General Description:

The Electro-Voice® Xi-1152A/94F is a second-generation
loudspeaker system ideal for professional touring or
installation applications requiring accurate, high-level
sound reinforcement from a very compact enclosure.
Because of the unique performance capabilities featured
in this system, the X-Array Install™ Xi-1152A/94F offers
extremely wide-range music reproduction as well as
accurate vocal coverage and maximized intelligibility. The
Xi-1152A/94F and associated controller combinations are
recommended for applications requiring full bandwidth
down to 44 Hz. Where very high levels of deep bass are
required, maximum performance may be achieved with the
addition of the Xi-1191A (single 18-inch subwoofer). The Xi­1 152A/94F features an EVX155 15” transducer and an ND6­16 3” voice coil Neodymium driver on a 1.4” horn throat exit,
providing extended frequency response with even, controlled
coverage. This system has integrated L-track rigging for
flying or arraying multiple enclosures.

Technical Specifications:

1

esnopseR.qerF

1

egnaR.qerF

1

Full Space measurement with a Dx38 Controller.

2

Download at www.electrovoice.com

:)Bd3-(zHk81-zH05
:)Bd01-(zHk02-zH44
:LPSdetaluclaCxaMkaePBd231,.gvA.tnoCBd621
:egarevoC)elbatatoR(°04x°09
:gnildnaHrewoPFLkaePW0042,suounitnoCW006
:gnildnaHrewoPFHkaePW003,suounitnoCW57
:ytivitisneSFLm1/W1,Bd99
:ytivitisneSFHm1/W1,Bd311
:ecnadepmIFL)lanimoN(smho8
:ecnadepmIFH)lanimoN(smho61
:recudsnarTFLsmho8,revirD)mm183("51551XVE
:recudsnarTFH.pmoCmgarhpaiD)mm67("361-6DN

smho61,revirD
:ycneuqerFrevossorCsretemaraPdednemmoceResU
:srotcennoCnokaepSkirtueNowT
:lairetaMerusolcnEdoowylphcriBylp-31
:ellirGleetsAG61
:)DxWxH(miDmm414x554x957

:thgieWteN)sbl08(gk3.63
:thgieWgnippihS)sbl58(gk6.83

2

®

)"3.61x"9.71x"9.92(

delellaraPs'4LN

Xi-1152A/94F Full Range Loudspeaker

Impedance:Frequency Response (Full & Half Space):

Horizontal Off Axis Frequency Response:Beamwidth:

Directivity:

Wiring Diagram:

Vertical Off Axis Frequency Response
(Up):

Vertical Off Axis Frequency Response
(Down):

Engineering Data Sheet

Horizontal 1/3 Octave Polars:

Vertical 1/3 Octave Polars:

Dimension Drawings:

CAUTION

This Xi Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the

X-Array Xi Install Flying Manual

hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.

Architectural & Engineering Specs:

The loudspeaker system shall be a two-way bi-amp system. The system shall have an 15-inch, low-frequency loudspeaker with a
nominal impedance of 8 ohms and a 4-inch aluminum voice coil. The low-frequency driver shall have a power-handling capacity of 600
watts for 8 hours (as per ANSI/EIA RS-426 A & AES 2-1984). The high-frequency section shall employ a compression driver capable of
handling 150 watts, 1,760- to 20,000-Hz when pink noise of a 6-dB crest factor is applied for 2 hours (as per AES 2-1984 and ANSI
S4.26-1984 standards). The loudspeaker shall be constructed of 18-mm, 13-ply birch and shall be trapezoidal in shape. The wedge
angle shall be 30-degrees. The grille shall be constructed from 16 GA powder-coated steel backed by acoustically transparent fabric.
The system shall be capable of very-high level operation with a band width of 48 to 18,000 Hz. The system dimensions shall be 455 mm
(17.90 inches) wide by 759 mm (29.88 inches) high by 414 mm (16.28 inches) deep. The system shall employ flying hardware of a
“track” style, having two tracks on the enclosure top and two tracks on the enclosure bottom. The enclosure shall include a stand mount
on the bottom of the enclosure. Net weight shall be 36.3 kg (80 lbs).

The loudspeaker shall be the Electro-Voice® Xi-1152A/94F.

12000 Portland Avenue South, Burnsville, MN 55337
Phone: [phone], Fax: [phone]

www.electro voice.com

© Telex Communications, Inc. 5/2004

Part Number 38110-273 Rev . A

and possible manual update notices. This system should be suspended with certified rigging

Performance Match

• P3000 (RL) • CPS 2.8 • Dx38

• P1200 (RL) • CPS 2.11

U.S.A. and Canada only. For customer orders, contact Customer Service at:

Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

Other International locations. For customer orders, contact Customer Service at:

For warranty repair or service information, contact the Service Repair department at:

For technical assistance, contact Technical Support at: 866/78AUDIO

Xi-1152A/94F Part Numbers

• 1057-3436 - Black

• 1057-3437- White

800/392-3497 Fax: [phone]

+ 49 9421-706 0 Fax: + 49 9421-706 265

+ 1 952 884-4051 Fax: + 1 952 736-4212

800/685-2606

Specifications subject to change without notice.