Electro-Voice XI-1122MHA-64F User Manual

Key Features:

• Compact/High-Level, T wo-W ay Design

• ND12A 12” Neodymium Mid-Bass Driver
(60° x 40° Coverage)

• Coaxially-Mounted ND6-16 3” Diaphragm HF
Compression Driver for Very High Output

• Fully Rotatable HF Section for Vertical or
Horizontal Suspension

• Ring-Mode Decoupling / RMD

• Built-In L-Track Rigging

• Available in Blac k or White

• Footprint Identical to Xi-1153A, Xi-1183A,
Xi-2153A, Xi-1191A, Xi-2181A, and Xi-2122MHA

TM

Xi-1122MHA/64F

12-Inch Two-Way,

Half-Height, Mid-High 60° x 40°

Sound Reinforcement System

The Electro-V oice® Xi-1122MHA/64F is a mid-high, two-way,
biamp system designed for medium- to long-throw
applications. The ND6-16 high-frequency driver/horn
combination is fully “shrouded” to preserve midbass wave­front detail. The ND12A 12-inch, application-specific mid­bass driver features RMD™ and a 60° x 40° horn. The 60° x
40° coverage pattern offers precise pattern control, and
would be well suited for front-of-house, front-fill, side-fill and
delay applications. When very high levels are desired we
suggest augmenting with the Xi-1191A. Its high-frequency
horn/driver section is rotatable to provide proper coverage
for vertical or horizontal system installations. The Xi­1122MHA/64F is a two-way system that requires an active
electronic crossover. Both the Electro-Voice Dx38 and Klark
Teknik DN9848 digital controllers are recommended for
signal control. The Electro-Voice P3000 amplifier is
recommended for powering the MB, and the P1200 is
recommended for powering the HF of the Xi-1122MHA/46F.

Technical Specifications:General Description:

1

esnopseR.qerF

1

egnaR.qerF

1

Full Space measurement with a Dx38 Controller

2

Max Calculated SPL of MB Section

3

Download at www.electrovoice.com

:)Bd3-(zHk71-zH011
:)Bd01-(zHk91-zH001

2

:Bd931

LPSdetaluclaCxaM

:egarevoC)elbatatoR(°04x°06
:gnildnaHrewoPBMkaePW0021,suounitnoCW003
:gnildnaHrewoPFHkaePW003,suounitnoCW57
:ytivitisneSBMm1/W1,Bd011
:ytivitisneSFHm1/W1,Bd211
:ecnadepmIBM)lanimoN(smho8
:ecnadepmIFH)lanimoN(smho61
:recudsnarTBMsmho8,revirD)mm503("21A21DN
:recudsnarTFH.pmoCmgarhpaiD)mm67("361-6DN

3

:sretemaraPdednemmoceResU

ycneuqerFrevossorC

:srotcennoCnokaepSkirtueNowT

:lairetaMerusolcnEdoowylphcriBylp-31
:ellirGleetsAG61
:)DxWxH(miDmm957x685x695

:thgieWteN)sbl631(gk8.16
:thgieWgnippihS)sbl541(gk8.56

smho61,revirD

®

delellaraP

)"9.92x"1.32x"5.32(

RPM8LN

Xi-1122MHA/64F Full Range Loudspeaker

Impedance:Frequency Response (Full & Half Space):

Horizontal Off Axis Frequency Response:Beamwidth:

Directivity:

Vertical Off Axis Frequency Response
(Up):

Vertical Off Axis Frequency Response
(Down):

Engineering Data Sheet

Horizontal 1/3 Octave Polars:

Vertical 1/3 Octave Polars:

Dimension Drawings:

Wiring/Connection Chart:

CAUTION

This Xi Loudspeaker should be suspended overhead only in accordance with the procedures and limitations specified in the

X-Array Xi Install Flying Manual

hardware by an authorized rigging professional and in compliance with local, state, and federal overhead suspension ordinances.

Architectural & Engineering Specs:

The loudspeaker system shall be a two-way bi-amp system. The system shall have a 12-inch, fully horn-loaded mid-bass driver
with a 2.5-inch voice coil and a nominal impedance of 8 ohms. The mid-bass driver shall have a power-handling capacity of 300
watts for 8 hours (as per ANSI/EIA RS-426 A & AES 2-1984). The high-frequency section shall be coaxially mounted in the mid-bass
horn and shall employ a compression driver capable of handling 75 watts, 1,760- to 20,000-Hz when pink noise of a 6-dB crest
factor is applied for 2 hours (as per AES 2-1984 and ANSI S4.26-1984 standards). The loudspeaker shall be constructed of 18-mm,
13-ply birch and shall be trapezoidal in shape. The wedge angle shall be 18-degrees. The grille shall be constructed from 16 GA
powder-coated steel backed by acoustically transparent fabric. The system shall be capable of very-high level operation with a band
width of 100 to 19,000 Hz. The system dimensions shall be 586 mm (23.07 inches) wide by 596 mm (23.46 inches) high by 759 mm
(29.88 inches) deep. The system shall employ flying hardware of a “track” style and two tracks on the enclosure top and two tracks on
the enclosure bottom. Net weight shall be 61.8 kg (136 lbs).

The loudspeaker shall be the Electro-Voice® Xi-1122MHA/64.

12000 Portland Avenue South, Burnsville, MN 55337
Phone: [phone], Fax: [phone]

www.electro voice.com

© T ele x Communications, Inc. 9/2004

Part Number 38110-367 Rev . A

and possible manual update notices. This system should be suspended with certified rigging

Performance Match

• P3000 (RL) • CPS 2.8 • Dx38

• P1200 (RL) • CPS 2.11

U.S.A. and Canada only. For customer orders, contact Customer Service at:

Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:

Other International locations. For customer orders, contact Customer Service at:

For warranty repair or service information, contact the Service Repair department at:

For technical assistance, contact Technical Support at: 866/78AUDIO

Xi-1122MHA/64F Part Numbers

• 1125-3443 - Black

• 1125-3446 - White

800/392-3497 Fax: [phone]

+ 49 9421-706 0 Fax: + 49 9421-706 265

+ 1 952 884-4051 Fax: + 1 952 736-4212

800/685-2606

Specifications subject to change without notice.