Page 1
Key Features:
• Integrated QuickSAMTM Heavy-Duty Strong-Arm Mounting
Bracket Included
• Indoor/Outdoor Design - Meets IEC 529, IP44 & MIL810
Environmental Specs
• EV8L 8” Weatherized Cone High-Output LF Transducer
• DH2005 1” Exit True Compression Driver
• 100° x 100° Coverage Pattern
• 200W Continuous, 800W Peak Power Handling
• High Sensitivity, 121 dB Maximum SPL
SL8.2
8-Inch Two-Way
Cinema Surround
Loudspeaker System
The Electro-Voice® SL8.2 is the new standard of no compromise audio performance and versatility in an easy to install, compact sound reinforcement package
for a wide array of cinema and theater surround applications.
The high-tech enclosure uses injection-molded high-impact polystyrene to make
the SL8.2 extremely durable. The enclosure geometry has been engineered to
provide maximum rigidity and acoustic performance. The velocity compensated
port design overcomes the limitation of many small cabinet loudspeakers and
enables exceptional low-frequency response without vent noise.
TM
SL8.2 installation is incredibly simple with the included QuickSAM
system. The QuickSAMTM is a unique, integrated mounting bracket which is
virtually foolproof. It allows the installer to simply snap the speaker onto the
bracket, then tighten it to the desired position. For array mounting, there is an
optional array bracket kit available which allows multiple units to be mounted
together for a variety of configurations.
The horn features 100° x 100° coverage for broad even dispersion needed in many
distributed audio applications.
The SL8.2 molded polymer enclosure is inherently water resistant. The addition of
a multilayer grille with hydrophobic cloth and weatherized components enable the
SL8.2 to perform under many environmental conditions. An optional weatherized
input panel cover with a gland nut is available for additional protection.
The SL8.2’s long excursion, high output 8" woofer with a weatherized treated cone
delivers smooth low-frequency performance with exceptional reliability. A sophisticated crossover network integrates it with the DH2005, a 1.25-inch voice coil true
compression driver for maximum output with extended frequency response. Fullbandwidth overload protection is provided for reliable, long term operation without
audible effect.
mounting
Technical Specifications:General Description:
1
esnopseR.qerF
1
egnaR.qerF
1
Half Space Measurement.
2
IEC Pink Noise, 6 dB Crest Factor.
:)Bd3-(zHk02-zH06
:)Bd01-(zHk02-zH84
:ycneuqerFssapiH.ceRzH04
1
ytivitisneSlaixA
:)m1/W1(Bd29
:LPSdetaluclaCxaMBd121
:egarevoClatnoziroH°001
:egarevoClacitreV°001
:rewoPmetsySdetaR.tnoCW002
:recudsnarTFLrevirD)mm302(ni8,L8VE
:recudsnarTFHtixE)mm4.52(.ni1,5002HD
moC
:ycneuqerFrevossorCzHk7.1
:ecnadepmIlanimoNsmhO8
:ecnadepmImuminiMsmhO6
:srotcennoCrotcennoCxineohPniP-4
:
lairetaMerusolcnEremyloPtcapmIhgiH
:noisnepsuSMASkciuQdetargetnI
:ellirGAG81,detaoCredwoPretseyloP
:)DxWxH(miDmm362xmm2
:thgieWteN)sbl5.81(gk4.8
:thgieWgnippihS)sbl5.22(gk2.01
2
revirDnoisserp
MT
leetSdezinavlaG
82xmm154
)"53.01x"21.11x"57.71(
kaePW008,.gorPW004,
ytuD-yvaeH
tekcarBgnitnuoMmrA-gnortS
Page 2
SL8.2 Full Range Loudspeaker
Frequency Response & Impedance:
Beamwidth:
Horizontal Off Axis Frequency Response:
Vertical Off Axis Frequency Response
(Up):
Block Diagram: Vertical Off Axis Frequency Response
(Down):
Page 3
Engineering Data Sheet
Horizontal 1/3 Octave Polars: Vertical 1/3 Octave Polars:
Page 4
Dimension Drawings:
Top View
Front View
Architectural and Engineering Specs:
The loudspeaker shall be a two-way system consisting of one 8"” (102mm) lowfrequency transducer, 1.25" titanium diaphragm true high-frequency compression
driver, and frequency dividing network installed in a vented enclosure. The network
shall include a full-range passive limiter for protection of both the low frequency and
high frequency transducers. The high frequency compression transducer shall drive
a horn to evenly cover a pattern of 100° by 100°. The enclosure shall be molded of
high impact polystyrene.
The finish shall be a paintable black. The grille shall be zinc plated, powder coated for
corrosion resistance, and equipped with both hydrophobic cloth and acoustic foam.
The loudspeaker position shall be adjustable over a range of 100° horizontally and 35°
vertically.
The support bracket shall be low profile and integral with the enclosure. The bracket
shall allow for a quick snap fit mounting of the speaker enclosure for placement
before securing. The speaker terminals shall include a 4 pin removable phoenix style
connector to allow for signal pass through. The system shall be weather resistant to
MIL Spec 810 and IEC 529 test conditions.
The loudspeaker system shall meet the following performance criteria: Power handling,
200-Watts long term program using IEC268-5 shaped pink noise; Frequency response,
48 Hz – 20 kHz (-10 dB from rated sensitivity); Pressure sensitivity, 92 dB at one
watt, 60 Hz – 20 kHz at one meter; Impedance, 8 ohms nominal, 6 ohms minimum.
The enclosure shall be 17.75" (451mm) high, 11.12" (282mm) wide, 10.35" (263mm)
deep. Net weight shall be 18.5 lbs (8.4 kg).
Right View
CAUTION
This SL8.2 Loudspeaker should be suspended overhead
only in accordance with the procedures and limitations
specified in the
update notices. This system should be suspended with
certified rigging hardware by an authorized rigging profes-
sional and in compliance with local, state, and federal
SL8.2 Part Number
• 301853-003 - SL8.2, 100° x 100° Horn, Black Finish
Performance Match
• D170261 CPS2.8, 120V Power Amplifier, 2 x 800W
Accessories
• 301918-001 AB-ZX1i, Array Bracket Kit for 2 or 4 Systems,
• 301955-001 TC-ZX1i, T erminal Cover with Gland Nut
ZX1 Users Manual
and possible manual
overhead suspension ordinances.
Black
12000 Portland Avenue South, Burnsville, MN 55337
Phone: 952/884-4051, Fax: 952/884-0043
www.electrovoice.com
© Telex Communications, Inc. 9/2005
Part Number 38110-471 Rev. A
U.S.A. and Canada only. For customer orders, contact Customer Service at:
800/392-3497 Fax: 800/955-6831
Europe, Africa, and Middle East only. For customer orders, contact Customer Service at:
+ 49 9421-706 0 Fax: + 49 9421-706 265
Other International locations. For customer orders, contact Customer Service at:
+ 1 952 884-4051 Fax: + 1 952 736-4212
For warranty repair or service information, contact the Service Repair department at:
800/685-2606
For technical assistance, contact Technical Support at: 866/78AUDIO
Specifications subject to change without notice.
Loading...